CPC1510

CPC1510
Single-Pole, Normally Open Relay
with Integrated Current Limit
INTEGRATED CIRCUITS DIVISION
Parameter
Blocking Voltage
Load Current
On-Resistance (max)
Rating
250
200
15
Units
VP
mArms / mADC

Features
•
•
•
•
•
•
•
•
•
Integrated Active Current-Limit Protection
Thermal Shutdown
Linear AC or DC Operation
Low Power Consumption
Clean, Bounce-free Switching
High Surge Capability
Low Power Drive Requirements
Surface Mount version available
Tape & Reel packaging available
Applications
Approvals
Ordering Information
AC/DC Configuration
– Control
Do Not Use
The relay is constructed using a GaAIAs LED for
actuation control and an integrated monolithic die for
the switch output. The die, fabricated in a
high-voltage dielectrically isolated technology,
comprises a photodiode array, switch control with
active current limiting circuitry, and MOSFET
switches. The active current limit circuitry in the
CPC1510 also provides a thermal shutdown feature
offering excellent power cross immunity for improved
survivability in harsh environments.
• UL Approved Component: File # E76270
• CSA Certified Component: Certificate # 1172007
• EN/IEC 60950-1 Certified Component:
Certificate B10 05 49410 006
Pin Configuration
1
The CPC1510 is a single-pole, normally
open (1-Form-A) Solid State Relay with an
integrated current limit feature that can replace
electromechanical relays while enhancing the
robustness of wireline-interface applications.
These enhancements greatly improve the robustness
of end systems using this device compared to
systems using relays without the integrated current
limit. In addition, the active current limit circuitry
enables the CPC1510 to pass FCC 68.302 and
other regulatory voltage surge requirements when
adequate overvoltage protection is provided. The
CPC1510 relay may be used in both unidirectional
DC applications as well as bi-directional AC
applications.
• General Telecom Switching
• Hook Switch
• Ringing Relay
• Dial Pulsing
• Ground Start
• Ground Fault Protection
• Instrumentation
• Automatic Tuning/Balancing
• Flying Capacitor
• Analog Multiplex
• Peripherals
• Automatic Tuning/Balancing
• Transducer Driver
• Security
• Medical Equipment
+ Control
Description
6
2
5
3
4
Load
Do Not Use
Load
Part #
CPC1510G
CPC1510GS
CPC1510GSTR
Description
6-Pin 0.250" Wide, Through Hole (50/Tube)
6-Pin 0.250" Wide, Surface Mount (50/Tube)
6-Pin 0.250" Wide, Surface Mount (1000/Reel)
Switching Characteristics of
Normally Open Devices
DC Only Configuration
+ Control
– Control
Do Not Use
1
6
2
5
3
4
+ Load
Form-A
– Load
IF
90%
10%
ILOAD
Pb
DS-CPC1510-R03
ton
e3
www.ixysic.com
toff
1
INTEGRATED CIRCUITS DIVISION
CPC1510
Absolute Maximum Ratings @ 25ºC
Parameter
Blocking Voltage
Reverse Input Voltage
Input LED Current
Continuous
Peak (10ms)
Input Control Current
Input Power Dissipation 1
Total Power Dissipation 2
Isolation Voltage, Input to Output
Operational Temperature
Storage Temperature
1
Derate Linearly 1.33 mW/ºC
2
Derate Linearly 1.67 mW/ºC
Ratings
250
5
Units
VP
V
50
1
10
150
800
3750
-40 to +85
-40 to +125
mA
A
mA
mW
mW
Vrms
°C
°C
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Recommended Operating Conditions
Parameter
Load Current, Continuous
Input Control Current
Operating Temperature Range
Symbol
IL
IF
TA
Configuration
AC/DC
DC-Only
-
Min
3
-40
Nominal
5
-
Max
200
350
10
+85
Units
mArms / mADC
mADC
mA
ºC
Electrical Characteristics @ 25ºC
Parameter
Output Characteristics
Current Limit
AC/DC Configuration
DC Configuration
On-Resistance
AC/DC Configuration
DC Configuration
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Input Characteristics
Input Control Current to Activate
Input Control Current to Deactivate
LED Forward Voltage
Common Characteristics
Input to Output Capacitance
2
Conditions
Symbol
Min
Typ
Max
Units
IF=5mA, VL=±5V,
t=5ms
ILMT
300
600
366
700
450
920
mAP
IF=5mA, IL=100mA
RON
VL=200V
ILEAK
6
1.5
-
11
2.8
0.02
15
3.75
1
µA
IF=5mA, IL=100mA
ton
toff
-
0.30
0.16
2
ms
IF=0mA, VL=1.0V,
f=1MHz
IF=0mA, VL=50V,
f=1MHz
CO
-
-
pF
IL=100mA
IL=100mA
IF=10mA
IF
IF
VF
0.2
1.15
1.29
2
1.45
mA
mA
V
-
CI/O
-
3
-
pF
www.ixysic.com

205
65
R03
INTEGRATED CIRCUITS DIVISION
CPC1510
PERFORMANCE DATA*
35
25
Device Count (N)
Device Count (N)
30
25
20
15
10
Typical Turn-On Time
(N=50, IF=5mA, IL=100mADC, TA=25ºC)
20
25
Device Count (N)
Typical LED Forward Voltage Drop
(N=50, IF=5mA, TA=25ºC)
15
10
5
5
0
0
LED Forward Voltage Drop (V)
Typical IF for Switch Operation
(N=50, IL=100mADC, TA=25ºC)
Typical IF for Switch Dropout
(N=50, TA=25ºC)
1.23
0.23
1.25
25
20
15
10
5
0
0.26
1.05
1.35
1.65
1.95
35
15
10
5
0.40
1.35
1.65
1.95
20
40
60
80
100
0.12
0.20
0.15
11
12
13
0.08
0.06
0.04
0.02
0
5
10
15
20
25
30
35
40
45
0
50
0
5
10
15
20
25
30
35
40
45
Temperature (ºC)
Forward Current (mA)
LED Forward Current (mA)
Maximum Load Current
vs. Temperature
Typical Turn-On vs. Temperature
(IL=100mADC)
Typical Turn-Off vs. Temperature
(IF=5mA, IL=100mADC)
0.35
400
AC/DC Configuration
300
IF=5mA
IF=10mA
200
IF=5mA
100
0
20
40
60
80
Temperature (ºC)
100
IF=5mA
0.4
0.3
IF=10mA
0.2
0.1
120
0
Turn-Off (ms)
IF=10mA
50
0.30
0.5
500
Turn-On (ms)
Load Current (mA)
10
0.10
0.25
0.6
-20
9
Typical Turn-Off Time
vs. LED Forward Current
(IL=100mADC)
DC Configuration
-40
10
Typical Turn-On Time
vs. LED Forward Current
(IL=100mADC)
0.30
120
600
0
15
On-Resistance (:)
0.00
0
20
8
0.05
-20
25
0.10
0.8
-40
0.37
LED Current (mA)
Turn-Off (ms)
Turn-On (ms)
IF=10mA
IF=5mA
1.0
0.32
Typical On-Resistance Distribution
(N=50, IF=5mA, IL=100mADC, TA=25ºC)
2.25
0.35
IF=50mA
0.22
0.27
Turn-Off (ms)
0
1.05
Typical LED Forward Voltage Drop
vs. Temperature
1.2
0.17
5
LED Current (mA)
1.4
5
30
0.75
1.6
10
0.12
20
2.25
1.8
15
0.38
0
0.75
LED Forward Voltage Drop (V)
0.35
Device Count (N)
1.21
Device Count (N)
Device Count (N)
25
1.19
20
0
0.29
0.32
Turn-On (ms)
1.17
Typical Turn-Off Time
(N=50, IF=5mA, IL=100mADC, TA=25ºC)
0.25
0.20
0.15
0.10
0.05
0
-40 -20
0
20
40
60
80
Temperature (ºC)
100 120
-40
-20
0
20
40
60
80
100
Temperature (ºC)
*The Performance Data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R03
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
CPC1510
PERFORMANCE DATA*
On-Resistance vs. Temperature
AC/DC Configuration
(IL=100mADC)
3.0
15
IF=10mA
10
5
1.5
1.0
-20
0
20
40
60
Temperature (ºC)
80
0
100
On-Resistance vs. Temperature
DC-Only Configuration
(IL=100mADC)
6
150
5
4
3
IF=10mA
2
1
0
-40
-20
0
20
40
60
80
100
Load Current (mA)
IF=5mA
-40
-20
0
20
40
60
Temperature (ºC)
80
1.5
1.0
0
100
-40
-20
0
20
40
60
80
100
Temperature (ºC)
Typical Load Current vs. Load Voltage
(TA=25ºC, IF=5mA)
Typical Leakage vs. Temperature
(Measured Across Pins 4&6)
0.035
0.030
100
50
0
-50
-100
0.025
0.020
0.015
0.010
0.005
-150
-2.5 -2.0 -1.5 -1.0 -0.5
0
0
-40
0.5 1.0 1.5 2.0 2.5
-20
0
Load Voltage (V)
Temperature (ºC)
1000
2.0
0.5
Leakage (PA)
-40
On-Resistance (:)
2.5
2.0
0.5
0
Typical IF for Switch Dropout
vs. Temperature
(IL=100mADC)
3.0
2.5
20
LED Current (mA)
On-Resistance (:)
IF=5mA
LED Current (mA)
25
Typical IF for Switch Operation
vs. Temperature
(IL=100mADC)
Typical Current Limit vs. Temperature
(IF=5mA)
1.2
20
40
60
80
100
Temperature (ºC)
Energy Rating Curve
(IF=5mA)
1.0
800
600
AC/DC Configuration
400
200
0
-40
Load Current (A)
Current Limit (mAP)
DC Configuration
0.8
0.6
0.4
0.2
-20
0
20
40
60
80
Temperature (ºC)
100
120
0
10μs 100μs 1ms 10ms 100ms
1s
10s
100s
Time
*The Performance Data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
4
www.ixysic.com
R03
INTEGRATED CIRCUITS DIVISION
CPC1510
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Rating
CPC1510G / CPC1510GS
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
Maximum Temperature x Time
CPC1510G / CPC1510GS
250ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb
R03
e3
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
CPC1510
Mechanical Dimensions
CPC1510G
8.382 ± 0.381
(0.330 ± 0.015)
PCB Hole Pattern
7.239 TYP
(0.285 TYP)
2.54 ± 0.127
(0.100 ± 0.005)
6 - 0.800 DIA.
(6 - 0.031 DIA.)
9.144 ± 0.508
(0.360 ± 0.020)
6.350 ± 0.127
(0.250 ± 0.005)
2.540 ± 0.127
(0.100 ± 0.005)
7.620 ± 0.127
(0.300 ± 0.005)
Pin 1
7.620 ± 0.254
(0.300 ± 0.010)
1.651 ± 0.254
(0.065 ± 0.010)
3.302 ± 0.051
(0.130 ± 0.002)
0.254 ± 0.0127
(0.010 ± 0.0005)
6.350 ± 0.127
(0.250 ± 0.005)
5.080 ± 0.127
(0.200 ± 0.005)
4.064 TYP
(0.160 TYP)
Dimensions
mm
(inches)
0.457 ± 0.076
(0.018 ± 0.003)
CPC1510GS
8.382 ± 0.381
(0.330 ± 0.015)
9.524 ± 0.508
(0.375 ± 0.020)
Pin 1
0.635 ± 0.127
(0.025 ± 0.005)
PCB Land Pattern
2.54 ± 0.127
(0.100 ± 0.005)
2.54
(0.10)
6.350 ± 0.127
(0.250 ± 0.005)
0.457 ± 0.076
(0.018 ± 0.003)
1.651 ± 0.254
(0.065 ± 0.010)
7.620 ± 0.254
(0.300 ± 0.010)
0.254 ± 0.0127
(0.010 ± 0.0005)
8.90
(0.3503)
1.65
(0.0649)
0.65
(0.0255)
3.302 ± 0.051
(0.130 ± 0.002)
4.445 ± 0.254
(0.175 ± 0.010)
Dimensions
mm
(inches)
1.651 ± 0.254
(0.065 ± 0.010)
6
www.ixysic.com
R03
INTEGRATED CIRCUITS DIVISION
CPC1510
CPC1510GSTR Tape & Reel
330.2 Dia
(13.00 Dia)
Top Cover
Tape Thickness
0.102 Max
(0.004 Max)
W=16.00
(0.63)
B0 = 10.10
(0.398)
K0 = 4.90
(0.19)
K1 = 3.80
(0.15)
P = 12.00
(0.472)
User Direction of Feed
Embossed
Carrier
Embossment
A0 = 10.10
(0.398)
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to
its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
7
Specification: DS-CPC1510-R03
©Copyright 2012, IXYS Integrated Circuits Division
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
12/16/2012