TS117L

TS117L
Multifunction Telecom Switch
INTEGRATED CIRCUITS DIVISION
Parameter
Blocking Voltage
Load Current
On-Resistance (max)
Rating
350
120
35
Units
VP
mArms / mADC

Features
• Current-Limited Relay
• 3750Vrms Input/Output Isolation
• Low Drive Power Requirements (TTL/CMOS
Compatible)
• FCC Compatible
• VDE Compatible
• No Moving Parts
• High Reliability
• Arc-Free With No Snubbing Circuits
• No EMI/RFI Generation
• Small 8-Pin Package
• Machine Insertable, Wave Solderable
• Surface Mount and Tape & Reel Versions Available
Applications
• Telecommunications
• Telecom Switching
• Tip/Ring Circuits
• Modem Switching (Laptop, Notebook, Pocket
Size)
• Hook Switch
• Dial Pulsing
• Ground Start
• Ringing Injection
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment-Patient/Equipment Isolation
• Security
• Aerospace
• Industrial Controls
Description
The TS117L integrated circuit device combines a
current-limited, 350V, normally open (1-Form-A) relay
and an optocoupler in a single package. The relay
uses optically coupled MOSFET technology to
provide 3750Vrms of input to output isolation.
Its optically coupled relay outputs, which use the
patented OptoMOS architecture, are controlled by a
highly efficient GaAIAs infrared LED.
The TS117L enables telecom circuit designers to
combine two discrete functions in a single component
that uses less space than traditional discrete
component solutions.
Approvals
• UL Recognized Component: File E76270
• CSA Certified Component: Certificate 1175739
• EN/IEC 60950 Certified Component:
TUV Certificate: B 10 05 49410 006
Ordering Information
Part #
TS117L
TS117PL
TS117PLTR
TS117LS
TS117LSTR
Description
8-Pin DIP (50/Tube)
8-Pin Flatpack (50/Tube)
8-Pin Flatpack (1000/Reel)
8-Pin Surface Mount (50/Tube)
8-Pin Surface Mount (1000/Reel)
Pin Configuration
+ LED - Relay
– LED - Relay
Collector - Phototransistor
Emitter - Phototransistor
1
8
2
7
3
6
4
5
Load - Relay (MOSFET Output)
Load - Relay (MOSFET Output)
LED - Phototransistor –/+
LED - Phototransistor +/–
Switching Characteristics of
Normally Open Devices
Form-A
IF
90%
10%
ILOAD
ton
Pb
DS-TS117L-R06
toff
e3
www.ixysic.com
1
INTEGRATED CIRCUITS DIVISION
TS117L
Absolute Maximum Ratings @ 25ºC
Parameter
Blocking Voltage
Input Power Dissipation 1
Input Control Current, Relay
Peak (10ms)
Reverse Input Voltage
Input Control Current, Detector
Total Power Dissipation 2
Isolation Voltage, Input to Output
Operational Temperature
Storage Temperature
1
Derate linearly 1.33 mW / ºC
2
Derate linearly 6.67 mW / ºC
Ratings
350
150
50
1
5
100
800
3750
-40 to +85
-40 to +125
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to the
device. Functional operation of the device at conditions beyond
those indicated in the operational sections of this data sheet is
not implied.
Units
VP
mW
mA
A
V
mA
mW
Vrms
°C
°C
Electrical Characteristics @25ºC: Relay Section
Parameter
Output Characteristics
Load Current, Continuous
Load Current Limit
On-Resistance
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Input Characteristics
Input Control Current to Activate
Input Control Current to Deactivate
Input Voltage Drop
Reverse Input Current
Common Characteristics
Input to Output Capacitance
Conditions
Symbol
Min
Typ
Max
Units
IL=120mA
VL=350V
IL
ICL
RON
ILEAK
130
-
170
30
-
120
210
35
1
mArms / mADC
mA

VL=50V, f=1MHz
ton
toff
COUT
-
25
3
3
-
ms
ms
pF
IL=120mA
IF=5mA
VR=5V
IF
IF
VF
IR
0.4
0.9
-
0.7
1.2
-
2
1.4
10
mA
mA
V
A
-
CI/O
-
3
-
pF
IF=5mA, VL=10V
A
Electrical Characteristics @25ºC: Detector Section
Parameter
Output Characteristics
Phototransistor Blocking Voltage
Phototransistor Dark Current
Saturation Voltage
Current Transfer Ratio
Input Characteristics
Input Control Current
Input Voltage Drop
Input Current (Detector Must be Off)
Isolation, Input to Output
2
Conditions
Symbol
Min
Typ
Max
Units
IC=10A
VCE=5V, IF=0mA
IC=2mA, IF=16mA
IF=6mA, VCE=0.5V
BVCEO
ICEO
VSAT
CTR
20
33
50
50
0.3
100
500
0.5
-
V
nA
V
%
IC=2mA, VCE=0.5V
IF=5mA
IC=1A, VCE=5V
-
IF
VF
IF
VI/O
0.9
5
3750
2
1.2
25
-
6
1.4
-
mA
V
A
Vrms
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
TS117L
RELAY PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
30
30
20
15
10
Device Count (N)
25
20
15
10
5
5
0
25
1.4875
1.6125
1.7375
25
20
15
10
5
0
0
1.3625
1.8625
0.15
0.25
0.35
0.45
0.55
0.65
0.025 0.075 0.125 0.175 0.225 0.275 0.325
0.75
LED Forward Voltage Drop (V)
Turn-On Time (ms)
Turn-Off Time (ms)
Typical IF for Switch Operation
(N=50, IL=120mADC)
Typical IF for Switch Dropout
(N=50, IL=120mADC)
Typical On-Resistance Distribution
(N=50, IF=2mA, IL=120mADC)
25
20
Device Count (N)
Device Count (N)
35
25
Device Count (N)
Device Count (N)
30
Typical Turn-Off Time
(N=50, IF=2mA, IL=120mADC)
Typical Turn-On Time
(N=50, IF=2mA, IL=120mADC)
15
10
5
0
35
30
20
Device Count (N)
35
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
15
10
5
0.75
1.05
1.35
1.65
1.95
20
15
10
5
0
0
0.45
25
0.45
2.25
0.75
1.05
1.35
1.65
1.95
17.0
2.25
17.4
17.8
18.2
18.6
19.0
On-Resistance (:)
LED Current (mA)
LED Current (mA)
Typical Blocking Voltage Distribution
(N=50)
35
Device Count (N)
30
25
20
15
10
5
0
376.25 382.75 389.25 395.75 402.25 408.75 415.25
Blocking Voltage (VP)
Typical Turn-On Time
vs. LED Forward Current
(IL=120mADC)
0.9
1.8
1.4
IF=50mA
IF=30mA
IF=20mA
IF=10mA
IF=5mA
1.2
1.0
0.8
0.35
0.7
Turn-Off Time (ms)
1.6
0.6
0.5
0.4
0.3
0.2
-20
0
20
40
60
Temperature (ºC)
80
100
120
0.30
0.25
0.20
0.15
0.10
0.05
0.1
0
0
-40
Typical Turn-Off Time
vs. LED Forward Current
(IL=120mADC)
0.40
0.8
Turn-On Time (ms)
LED Forward Voltage Drop (V)
Typical LED Forward Voltage Drop
vs. Temperature
0
5
10
15
20
25
30
35
40
LED Forward Current (mA)
45
50
0
5
10
15
20
25
30
35
40
45
50
LED Forward Current (mA)
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R06
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
TS117L
RELAY PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
Typical Turn-On Time
vs. Temperature
(IL=120mADC)
1.2
1.0
0.8
0.6
IF=5mA
IF=10mA
IF=20mA
0.4
0.2
0.5
IF=2mA
0.4
0.3
0.2
IF=5mA
0.1
-40
-20
0
20
40
60
80
100
120
Typical IF for Switch Operation
vs. Temperature
(IL=120mADC)
30
20
-20
0
20
40
60
80
-40
100
100
0.5
Load Current (mA)
150
1.0
2.5
2.0
1.5
1.0
0
-20
0
20
40
60
80
3
4
50
0
-50
-20
0
20
40
60
80
100
-4
-3
-2
-1
0
1
2
Temperature (ºC)
Load Voltage (V)
Maximum Load Current
vs. Temperature
Typical Blocking Voltage
vs. Temperature
Typical Leakage vs. Temperature
Measured across Pins 7&8
Blocking Voltage (VP)
160
140
120
100
IF=10mA
IF=5mA
IF=2mA
80
60
40
20
0
420
0.014
410
0.012
400
390
380
370
0
20
40
60
80
100
-40
120
-20
0
0.008
0.006
20
40
60
80
0.002
-40
100
-20
0
Temperature (ºC)
Temperature (ºC)
40
60
80
100
400
350
300
Current (mA)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10Ps 100Ps 1ms 10ms 100ms
20
Temperature (ºC)
Typical Current Limiting
vs. Temperature
Energy Rating Curve
Load Current (A)
0.010
0.004
360
-20
100
Temperature (ºC)
180
-40
80
-150
-40
100
Leakage (PA)
-40
60
-100
0.5
0
40
Typical Load Current
vs. Load Voltage
(IF=2mA)
3.0
1.5
20
Typical IF for Switch Dropout
vs. Temperature
(IL=120mADC)
3.5
2.0
0
Temperature (ºC)
3.0
2.5
-20
Temperature (ºC)
3.5
LED Current (mA)
LED Current (mA)
40
0
-40
Temperature (ºC)
Load Current (mA)
50
10
0
0
Typical On-Resistance
vs. Temperature
(IF=2mA, IL=120mADC)
60
0.6
Turn-Off Time (ms)
Turn-On Time (ms)
0.7
IF=2mA
1.4
On-Resistance (:)
1.6
Typical Turn-Off Time
vs. Temperature
(IL=120mADC)
250
200
150
100
50
0
1s
10s
100s
-40
-20
0
20
40
60
80
100
Temperature (ºC)
Time
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
4
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
TS117L
DETECTOR PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
8
4.0
7
3.5
3.0
2.5
2.0
1.5
1.0
6
5
4
2
1
0
0
4
6
8
10
12
14
Forward Current (mA)
16
18
20
IF=1mA
IF=2mA
IF=5mA
IF=10mA
IF=15mA
IF=20mA
3
0.5
2
12
-40
-20
0
20
40
60
80
Temperature (ºC)
100
120
Collector Current (mA)
4.5
0
Typical Collector Current
vs. Forward Current
(VCE=0.5V)
Typical Normalized CTR
vs. Temperature
(VCE=0.5V)
Normalized CTR (%)
Normalized CTR (%)
Typical Normalized CTR
vs. Forward Current
(VCE=0.5V)
10
8
6
4
2
0
0
2
4
6
8
10
12
14
16
18
20
Forward Current (mA)
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R06
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
TS117L
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the
latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Rating
TS117L / TS117PL / TS117LS
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
Maximum Temperature x Time
TS117L / TS117LS
250ºC for 30 seconds
TS117PL
260ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an
optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a
wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb
6
e3
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
TS117L
Mechanical Dimensions
TS117L
2.540 ± 0.127
(0.100 ± 0.005)
9.652 ± 0.381
(0.380 ± 0.015)
8-0.800 DIA.
(8-0.031 DIA.)
2.540 ± 0.127
(0.100 ± 0.005)
9.144 ± 0.508
(0.360 ± 0.020)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
PCB Hole Pattern
7.620 ± 0.254
(0.300 ± 0.010)
6.350 ± 0.127
(0.250 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
0.457 ± 0.076
(0.018 ± 0.003)
7.620 ± 0.127
(0.300 ± 0.005)
7.239 TYP.
(0.285)
4.064 TYP
(0.160)
7.620 ± 0.127
(0.300 ± 0.005)
0.254 ± 0.0127
(0.010 ± 0.0005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
TS117PL
0 MIN / 0.102 MAX
(0 MIN / 0.004 MAX)
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
7.620 ± 0.254
(0.300 ± 0.010)
9.398 ± 0.127
(0.370 ± 0.005)
Pin 1
2.286 MAX.
(0.090 MAX.)
2.54
(0.10)
0.635 ± 0.127
(0.025 ± 0.005)
8.70
(0.3425)
1.55
(0.0610)
0.203 ± 0.013
(0.008 ± 0.0005)
9.652 ± 0.381
(0.380 ± 0.015)
PCB Land Pattern
0.65
(0.0255)
2.159 ± 0.025
(0.085 ± 0.001)
0.457 ± 0.076
(0.018 ± 0.003)
0.864 ± 0.120
(0.034 ± 0.004)
Dimensions
mm
(inches)
TS117LS
9.652 ± 0.381
(0.380 ± 0.015)
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
0.635 ± 0.127
(0.025 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
9.525 ± 0.254
(0.375 ± 0.010)
0.457 ± 0.076
(0.018 ± 0.003)
PCB Land Pattern
2.54
(0.10)
8.90
(0.3503)
1.65
(0.0649)
7.620 ± 0.254
(0.300 ± 0.010)
0.254 ± 0.0127
(0.010 ± 0.0005)
0.65
(0.0255)
4.445 ± 0.127
(0.175 ± 0.005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
R06
www.ixysic.com
7
INTEGRATED CIRCUITS DIVISION
TS117L
TS117LSTR Tape & Reel
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
W=16.00
(0.63)
Bo=10.30
(0.406)
K0 =4.90
(0.193)
Ao=10.30
(0.406)
K1 =4.20
(0.165)
Embossed Carrier
Embossment
P=12.00
(0.472)
User Direction of Feed
Dimensions
mm
(inches)
NOTES:
1. Dimensions carry tolerances of EIA Standard 481-2
2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
TS117PLTR Tape & Reel
2.00
(0.079)
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
Embossment
W = 16.00
(0.63)
7.50
(0.295)
Bo = 10.30
(0.406)
K0 = 2.70
(0.106)
K1 = 2.00
(0.079)
Embossed Carrier
4.00
(0.157)
P = 12.00
(0.472)
User Direction of Feed
Ao = 10.30
(0.406)
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to
its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
8
Specification: DS-TS117L-R06
©Copyright 2013, IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
6/20/2013