Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag Fuse > 215SP Series 215SP Series, 5×20 mm, Time-Lag Fuse RoHS Pb PS E Description 5×20mm Time-Lag surge withstanding ceramic body cartridge fuse designed to IEC specification Features • Designed to International (IEC) Standards for use globally • High breaking capacity • RoHS compliant and lead-free • Meets the IEC 60127-2, Sheet 5 specification for Time-Lag Fuses Applications Agency Approvals AGENCY AGENCY FILE NUMBER AMPERE RANGE PS E NBK080205-E10480B NBK250702-E10480F 1A – 5A 6.3A – 10A CQC10012041490 1A – 6.3A SU05001-2011B SU05001-10001 SU05001-10002 SU05001-2012B 1A – 2.5A 3.15A – 6.3A 8A 10A E10480 1A – 10A 29862 1A – 10A 40013521 1 – 10A J50248091 10A N/A 1A – 10A Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. Electrical Characteristics for Series % of Ampere Rating 210% 275% 400% 1000% Ampere Rating Opening Time 1A - 3.15A 4A - 6.3A 8A - 10A 1A - 3.15A 4A - 6.3A 8A - 10A 1A - 3.15A 4A - 6.3A 8A - 10A 1A - 3.15A 4A - 6.3A 8A - 10A 30 minutes, Maximum 30 minutes, Maximum 30 minutes, Maximum .75 sec. Min.; 80 secs. Max. .75 sec. Min.; 80 secs. Max. .75 sec. Min.; 80 secs. Max. .095 sec. Min.; 5 secs. Max. .150 sec. Min.; 5 secs. Max. .150 sec. Min.; 5 secs. Max. .010 sec. Min.; .150 secs. Max. .010 sec. Min.; .150 secs. Max. .010 sec. Min.; .150 secs. Max. Electrical Characteristic Specifications by Item Nominal Amp Amp Voltage Interrupting Resistance Rating Code Rating Rating Cold Ohms (Ohms) Maximum Nominal Voltage Drop at Melting I2t Rated Current (A2 sec) (mV) Maximum Power Dissapation at 1.5ln (W) Agency Approvals PS E 001 1 250 0.1515 1.52000 350 2.5 x x x x x x x 1.25 1.25 250 0.1074 3.20000 300 2.5 x x x x x x x 01.6 1.6 250 0.0707 6.83000 200 2.5 x x x x x x x 002 2 250 0.0566 11.68000 190 2.5 x x x x x x x 02.5 2.5 250 0.0386 22.29000 180 2.5 x x x x x x x 3.15 3.15 250 0.0283 43.25500 140 4 x x x x x x x 004 4 250 0.0185 46.96000 100 4 x x x x x x x 005 5 250 0.0153 66.09500 100 4 x x x x x x x 06.3 6.3 250 0.0108 128.75000 100 4 x x x x x x x 008 8 250 0.0092 209.88000 100 4 x x x x x 010 10 250 0.0066 333.56500 100 4 x x x x x 1500 A @ 250 VAC x x x I2t test at 10x rated current © 2016 Littelfuse, Inc. Application testing is strongly recommended. Specifications are subject to change without notice. Revised: 01/08/16 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag Fuse > 215SP Series Average Time Current Curves 215001. 2151.25 21501.6 215002. 21502.5 2153.15 215004. 215005. 21506.3. 215008. 215010. Temperature Re-rating Curve 10000 1000 100 Time (seconds) 10 1 0.1 Note: Rerating depicted in this curve is in addition to the standard derating of 25% for continuous operation. 0.01 0.001 0.01 0.1 1 10 100 Amps Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 Wave Parameter 260 Lead-Free Recommendation Preheat: 240 220 (Depends on Flux Activation Temperature) 200 180 160 140 120 100 80 60 (Typical Industry Recommendation) Temperature Minimum: 100°C Temperature Maximum: Preheat Time: 150°C 60-180 seconds Solder Pot Temperature: 260°C Maximum Solder Dwell Time: 2-5 seconds 40 Time (Seconds) Cooling Time Preheat Time Dwell Time 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 0 20 20 10 Temperature (°C) - Measured on bottom side of board 300 Recommended Hand-Solder Parameters: Solder Iron Temperature: 350°C +/- 5°C Heating Time: 5 seconds max. Note: These devices are not recommended for IR or Convection Reflow process. A Different values of A and B available, please contact the Littelfuse sales representative in your region: For the pigtailed fuse, please follow the recommendations B A below for axial lead forming and mounting into PCB: C Lead forming: The distance C between cap flat surface and axial lead shall be greater than 1.0 mm. C PCB mounting: The distance between PCB and fuse cap is recommended to B be a minimum of 1.5 mm. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/08/16 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag Fuse > 215SP Series Product Characteristics Part Numbering System Materials Body: Ceramic Cap: Nickel–plated Brass Leads: Tin–plated Copper Terminal Strength MIL-STD-202, Method 211, Test Condition A Solderability MIL-STD-202 Method 208 Product Marking Cap 1: Brand logo, current and voltage ratings Cap 2: Agency approval marks 0215 xxxx M X E SP P Series Lead-Free Current Rating Code Single-Cap Pigtail Refer to Amp Code column of Electrical Characteristics Table Option Codes Quantity Code Blank : Cartidge Type Fuse E : Axial Leaded Fuse M = 1000 Packaging Code X = Filler Operating Temperature –55ºC to +125ºC Thermal Shock MIL-STD-202, Method 107, Test Condition B (5 cycles, –65ºC to +125ºC) Vibration MIL-STD-202, Method 201 Humidity MIL-STD-202, Method 103, Test Condition A (High RH (95%) and elevated temp (40ºC) for 240 hours) Salt Spray MIL-STD-202, Method 101, Test Condition B Packaging Packaging Option Packaging Specification Quantity Packaging Code Reel Size 215SP Series Bulk N/A 1000 MXE N/A Additional Information Dimensions All dimensions in mm 40 ± 1.0 20 ± 0.5 +0.1 ø5.2 -0.2 Datasheet ø0.65±0.05* 5.1 ± 0.6 Resources Samples 5.1 ± 0.6 Notes: * Ratings 8A and 10A have 0.8 ± 0.05 diameter lead. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/08/16