TVS Diodes Axial Leaded – 500W > SA series SA Series RoHS Pb e3 Description The SA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features Uni-directional • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) (αT:Temperature Coefficient) • Low incremental surge • Glass passivated chip resistance junction in DO-15 Package • Typical IR less than 1μA • 500W peak pulse above 13V capability at 10/1000μs waveform, repetition rate • High temperature (duty cycles):0.01% soldering guaranteed: 260°C/40 seconds / • Fast response time: 0.375”,(9.5mm) lead typically less than 1.0ps length, 5 lbs., (2.3kg) from 0 Volts to BV min tension • Excellent clamping • Plastic package has capability underwriters laboratory • Typical failure mode is flammability classification short from over-specified 94V-O voltage or current • Matte tin lead–free plated • Whisker test is conducted • Halogen free and RoHS based on JEDEC compliant JESD201A per its table 4a and 4c • 2nd level interconnect is Pb-free per IPC/JEDEC • IEC-61000-4-2 ESD J-STD-609A.01 15kV(Air), 8kV (Contact). • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • VBR @TJ= VBR@25°C x (1+αT x (TJ - 25)) Agency Approvals AGENCY AGENCY FILE NUMBER E128662/E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 500 W PD 3.0 W IFSM 70 A VF 3.5/5.0 V TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RuJL 20 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2) (Note 1) Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC (Fig. 6) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 35A for Unidirectional Only (Note 3) Operating Junction and Storage Temperature Range Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. _ 200V and VF<5.0V for devices of VBR > _ 201V. 3. VF<3.5V for devices of VBR < Functional Diagram Bi-directional Cathode Anode Uni-directional SA Series 102 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded – 500W > SA series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (V) SA5.0A SA6.0A SA6.5A SA7.0A SA7.5A SA8.0A SA8.5A SA9.0A SA10A SA11A SA12A SA13A SA14A SA15A SA16A SA17A SA18A SA20A SA22A SA24A SA26A SA28A SA30A SA33A SA36A SA40A SA43A SA45A SA48A SA51A SA54A SA58A SA60A SA64A SA70A SA75A SA78A SA85A SA90A SA100A SA110A SA120A SA130A SA150A SA160A SA170A SA180A SA5.0CA SA6.0CA SA6.5CA SA7.0CA SA7.5CA SA8.0CA SA8.5CA SA9.0CA SA10CA SA11CA SA12CA SA13CA SA14CA SA15CA SA16CA SA17CA SA18CA SA20CA SA22CA SA24CA SA26CA SA28CA SA30CA SA33CA SA36CA SA40CA SA43CA SA45CA SA48CA SA51CA SA54CA SA58CA SA60CA SA64CA SA70CA SA75CA SA78CA SA85CA SA90CA SA100CA SA110CA SA120CA SA130CA SA150CA SA160CA SA170CA SA180CA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Breakdown Voltage VBR (Volts) @ IT Maximum Clamping Voltage VC@ IPP (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (µA) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 289.0 55.4 49.5 45.5 42.5 39.5 37.5 35.4 33.1 30.0 28.0 25.6 23.7 22.0 20.9 19.6 18.5 17.5 15.7 14.4 13.1 12.1 11.2 10.5 9.6 8.8 7.9 7.3 7.0 6.6 6.2 5.9 5.4 5.3 5.0 4.5 4.2 4.0 3.7 3.5 3.1 2.9 2.6 2.4 2.1 2.0 1.9 1.7 600 600 400 150 50 25 10 5 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is + 10% and Vc is 5% higher than with A parts. SA Series 103 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded – 500W > SA series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR V IR VF IT IT IR Vc VBR VR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM- Peak Pulse Power (KW) 30 Voltage or Current Voltage Across TVS Current Through TVS Non-repetitive Pulse Waveform Shown in Fig. 3 TA=25ûC 10 1 P P P 0.1 01.µs Exponential Td Td Half SINE Td 1.0µs Square 10µs 100µs 1.0ms 10ms td- Pulse Width (sec.) Time continues on next page. SA Series 104 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded – 500W > SA series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 100 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % Figure 3 - Pulse Derating Curve 75 50 25 0 0 25 50 75 100 125 150 tr=10µsec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 0 175 200 1.0 0 TA- Ambient Temperature (˚C) 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve 10000 3.5 Steady State Power Dissipation (W) Bi-directional V=0V Uni-directional V=0V 1000 Uni-directional @ VR Cj (pF) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 100 Bi-directional @ VR 10 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 10.0 100.0 3 2.5 2 1.5 1 0.5 0 1000.0 VBR - Reverse Breakdown Voltage (V) L = 0.375” (9.5mm) Lead Lengths 0 25 50 75 100 125 150 175 200 TL - Lead Temperature(ºC) Figure 7 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 80 70 60 50 40 30 20 10 0 SA Series 1 10 Number of Cycles at 60 Hz 100 105 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded – 500W > SA series Soldering Parameters Pre Heat Lead–free assembly Ramp-up - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs TL Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow tp TP Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Critical Zone TL to TP t 25˚C to Peak Time (t) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6°C/second max Peak Temperature : 265OC Time 25°C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 280°C Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.015oz., 0.4g High Temp. Storage JESD22-A103 Case JEDEC DO-204AC (DO-15) molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 Dimensions D Dimensions Cathode Band (for Uni-directional products only) C A B A Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.230 0.300 5.80 7.60 C 0.028 0.034 0.71 0.86 D 0.104 0.140 2.60 3.60 DO-204AC (DO-15) SA Series 106 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded – 500W > SA series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) Littelfuse Logo (for Uni-directional products only) VBR VOLTAGE CODE (Refer to the Electrical Characteristics table) F SAxxx XX X YYWW Trace Code Marking SAXXX YY:Year Code WW: Week Code Product Type SERIES CODE Packaging Part Number Component Package Quantity Packaging Option SAxxxXX DO-204AC 4000 Tape & Reel EIA STD RS-296 SAxxxXX-B DO-204AC 1000 Bulk Littelfuse Spec. Packaging Specification Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.197+/-0.020 (5.0+/- 0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) SA Series Direction of Feed 107 ©2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14