Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series 5KP Series RoHS Pb e3 Description Uni-directional The 5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 5000 W PD 8.0 W IFSM 400 A VF 3.5/5.0 V TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RθJA 40 °C/W Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2) (Note 1) Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 3) Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2.Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. 3.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. Functional Diagram • 5000W peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Glass passivated chip junction in P600 package • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) •E SD protection of data lines in accordance with IEC 61000-4-2 •E FT protection of data lines in accordance with IEC 61000-4-4 • Low incremental surge resistance • Typical IR less than 2μA when VBR min>12V • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”, (9.5mm) lead length, 5 lbs., (2.3kg) tension • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Plastic package is flammability rated V-0 per Underwriters Laboratories • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD- Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) 5KP5.0A 5KP6.0A 5KP6.5A 5KP7.0A 5KP7.5A 5KP8.0A 5KP8.5A 5KP9.0A 5KP10A 5KP11A 5KP12A 5KP13A 5KP14A 5KP15A 5KP16A 5KP17A 5KP18A 5KP20A 5KP22A 5KP24A 5KP26A 5KP28A 5KP30A 5KP33A 5KP36A 5KP40A 5KP43A 5KP45A 5KP48A 5KP51A 5KP54A 5KP58A 5KP60A 5KP64A 5KP70A 5KP75A 5KP78A 5KP85A 5KP90A 5KP100A 5KP110A 5KP120A 5KP130A 5KP150A 5KP160A 5KP170A 5KP180A 5KP190A 5KP200A 5KP210A 5KP220A 5KP250A 5KP5.0CA 5KP6.0CA 5KP6.5CA 5KP7.0CA 5KP7.5CA 5KP8.0CA 5KP8.5CA 5KP9.0CA 5KP10CA 5KP11CA 5KP12CA 5KP13CA 5KP14CA 5KP15CA 5KP16CA 5KP17CA 5KP18CA 5KP20CA 5KP22CA 5KP24CA 5KP26CA 5KP28CA 5KP30CA 5KP33CA 5KP36CA 5KP40CA 5KP43CA 5KP45CA 5KP48CA 5KP51CA 5KP54CA 5KP58CA 5KP60CA 5KP64CA 5KP70CA 5KP75CA 5KP78CA 5KP85CA 5KP90CA 5KP100CA 5KP110CA 5KP120CA 5KP130CA 5KP150CA 5KP160CA 5KP170CA 5KP180CA 5KP190CA 5KP200CA 5KP210CA 5KP220CA 5KP250CA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 190.0 200.0 210.0 220.0 250.0 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.00 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 110.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 211.00 222.00 233.00 244.00 277.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 233.00 246.00 258.00 270.00 306.00 50 50 50 50 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Maximum Clamping Voltage VC @ IPP (V) Maximum Peak Pulse Current IPP (A) Maximum Reverse Leakage IR @ VR (µ A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 310.0 329.2 349.5 371.1 425.0 554.3 495.1 455.4 425.0 395.3 375.0 354.2 331.2 300.0 280.2 256.3 237.2 219.8 209.0 196.2 184.8 174.7 157.4 143.7 131.1 121.1 112.3 105.4 95.7 87.8 79.1 73.5 70.2 65.9 61.9 58.6 54.5 52.7 49.5 45.1 42.1 40.5 37.2 34.9 31.5 28.8 26.4 24.4 21.0 19.7 18.5 17.5 16.5 15.5 14.6 13.7 12.0 5000 5000 2000 1000 250 150 50 20 15 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IT IR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 1000 PPPM-Peak Pulse Power (KW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS TJ initial = Tamb 100 5kW at 10x1000µs, 25°C 10 1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 150 100 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 75 50 25 0 0 25 50 75 100 125 150 175 200 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 100000 10000 Transient Thermal Impedance (°C/W) Uni-direconal V=0V Cj (pF) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 0 TJ - Initial Junction Temperature (ºC) Bi-direconal V=0V Uni-direconal V=VR 1000 100 Bi-direconal V=VR 10 1 1 10 100 10 1 0.1 1000 0.01 VBR - Reverse Breakdown Voltage (V) 0.1 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 500 Single die 100 450 IF- Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) tr=10µsec 400 350 300 250 200 150 100 50 10 Stacked-die 1 0.1 0.01 0 1 10 Number of Cycles at 60 Hz © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 100 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 VF-Peak Forward Voltage(V) 8.0 9.0 10.0 Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series Soldering Parameters Lead–free assembly Reflow Condition Pre Heat Ramp-up 150°C TL - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max TS(max) to TA - Ramp-up Rate 3°C/second max Reflow Temperature (T) - Temperature Min (Ts(min)) tp TP tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Critical Zone TL to TP t 25˚C to Peak Time (t) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6°C/second max Peak Temperature : 265OC Time 25°C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 260°C Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.07oz., 2.1g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 Dimensions D Cathode Band (for Uni-directional products only) C A B A Dimensions Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 P600 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 5000W > 5KP series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band (for Uni-directional products only) TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) F 5KPxxx XX X YYWW Trace Code Marking Littelfuse Logo 5KPXXX VR VOLTAGE Product Type SERIES CODE Packing Options Component Package Quantity Packaging Option 5KPxxxXX P600 800 Tape & Reel EIA STD RS-296 5KPxxxXX-B P600 100 BULK Littelfuse Spec. Part Number YY:Year Code WW: Week Code Packaging Specification Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Direction of Feed