Datasheet

Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
1.5KE Series
RoHS
Pb e3
Description
The 1.5KE Series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Uni-directional
Features
Bi-directional
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E230531
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Parameter
Symbol
Value
Unit
PPPM
1500
W
PD
6.5
W
IFSM
200
A
VF
3.5/5.0
V
TJ , TSTG
-55 to 175
°C
Typical Thermal Resistance
Junction to Lead
RθJL
15
°C/W
Typical Thermal Resistance
Junction to Ambient
RθJA
75
°C/W
Peak Pulse Power Dissipation by
10/1000μs Test Waveform (Fig.2)
(Note 1), (Note 4)
Steady State Power Dissipation on
Infinite Heat Sink at TL=75ºC
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave Unidirectional
Only (Note 2)
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional
Only (Note 3)
Operating Junction and Storage
Temperature Range
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3.
2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per
minute maximum.
3.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts.
4. The PPPM of stacked-die parts is 2kW and please contact littelfuse for the detail
stacked-die parts.
• 1500W peak pulse
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
• Glass passivated chip
junction in DO-201
Package
• Fast response time:
typically less than 1.0ps
from 0 Volts to BV min
• Excellent clamping
capability
• Typical failure mode is
short from over-specified
voltage or current
• Whisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
• IEC-61000-4-2 ESD
30kV(Air), 30kV (Contact)
•E
SD protection of data
lines in accordance with
IEC 61000-4-2
•E
FT protection of data
lines in accordance with
IEC 61000-4-4
• Low incremental surge
resistance
• Typical IR less than 1μA
when VBR min>12V
• High temperature
to reflow soldering
guaranteed: 260°C/40sec
/ 0.375”,(9.5mm) lead
length, 5 lbs., (2.3kg)
tension
• VBR @ TJ= VBR@25°C
x (1+αT x (TJ - 25))
(αT:Temperature
Coefficient, typical value
is 0.1%)
• Plastic package is
flammability rated V-0 per
Underwriters Laboratories
• Matte tin lead–free plated
• Halogen free and RoHS
compliant
• Pb-free E3 means 2nd
level interconnect is
Pb-free and the terminal
finish material is tin(Sn)
(IPC/JEDEC J-STD609A.01)
Applications
TVS devices are ideal for the protection of I/O interfaces,
VCC bus and other vulnerable circuits used in telecom,
computer, industrial and consumer electronic applications.
Additional Infomarion
Functional Diagram
Datasheet
Bi-directional
Cathode
Anode
Uni-directional
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Resources
Samples
Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
Electrical Characteristics (T =25°C unless otherwise noted)
A
Test
Current
IT (mA)
Maximum
Clamping
Voltage
VC @ Ipp
(Volts)
Maximum
Peak Pulse
Current Ipp
(A)
Maximum
Reverse
Leakage IR @
VR (µA)
Agency
Approval
7.14
7.88
8.61
9.50
10.50
11.60
12.60
13.70
15.80
16.80
18.90
21.00
23.10
25.20
28.40
31.50
34.70
37.80
41.00
45.20
49.40
53.60
58.80
65.10
71.40
78.80
86.10
95.50
105.00
116.00
126.00
137.00
158.00
168.00
179.00
189.00
210.00
231.00
263.00
315.00
336.00
368.00
420.00
462.00
504.00
535.00
556.50
567.00
577.50
10
10
10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10.5
11.3
12.1
13.4
14.5
15.6
16.7
18.2
21.2
22.5
25.2
27.7
30.6
33.2
37.5
41.4
45.7
49.9
53.9
59.3
64.8
70.1
77.0
85.0
92.0
103.0
113.0
125.0
137.0
152.0
165.0
179.0
207.0
219.0
234.0
246.0
274.0
328.0
344.0
414.0
441.0
482.0
548.0
602.0
658.0
698.0
725.0
740.0
760.0
144.8
134.5
125.6
113.4
104.8
97.4
91.0
83.5
71.7
67.6
60.3
54.9
49.7
45.8
40.5
36.7
33.3
30.5
28.2
25.6
23.5
21.7
19.7
17.9
16.5
14.8
13.5
12.2
11.1
10.0
9.2
8.5
7.3
6.9
6.5
6.2
5.5
4.6
4.4
3.7
3.5
3.2
2.8
2.5
2.3
2.1
2.1
2.0
2.0
1000
500
200
50
10
5
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
630.00
1
828.0
1.8
1
Part
Number
(Uni)
Part
Number
(Bi)
Reverse
Stand off
Voltage VR
(Volts)
MIN
MAX
1.5KE6.8A
1.5KE7.5A
1.5KE8.2A
1.5KE9.1A
1.5KE10A
1.5KE11A
1.5KE12A
1.5KE13A
1.5KE15A
1.5KE16A
1.5KE18A
1.5KE20A
1.5KE22A
1.5KE24A
1.5KE27A
1.5KE30A
1.5KE33A
1.5KE36A
1.5KE39A
1.5KE43A
1.5KE47A
1.5KE51A
1.5KE56A
1.5KE62A
1.5KE68A
1.5KE75A
1.5KE82A
1.5KE91A
1.5KE100A
1.5KE110A
1.5KE120A
1.5KE130A
1.5KE150A
1.5KE160A
1.5KE170A
1.5KE180A
1.5KE200A
1.5KE220A
1.5KE250A
1.5KE300A
1.5KE320A
1.5KE350A
1.5KE400A
1.5KE440A
1.5KE480A
1.5KE510A
1.5KE530A
1.5KE540A
1.5KE550A
1.5KE6.8CA
1.5KE7.5CA
1.5KE8.2CA
1.5KE9.1CA
1.5KE10CA
1.5KE11CA
1.5KE12CA
1.5KE13CA
1.5KE15CA
1.5KE16CA
1.5KE18CA
1.5KE20CA
1.5KE22CA
1.5KE24CA
1.5KE27CA
1.5KE30CA
1.5KE33CA
1.5KE36CA
1.5KE39CA
1.5KE43CA
1.5KE47CA
1.5KE51CA
1.5KE56CA
1.5KE62CA
1.5KE68CA
1.5KE75CA
1.5KE82CA
1.5KE91CA
1.5KE100CA
1.5KE110CA
1.5KE120CA
1.5KE130CA
1.5KE150CA
1.5KE160CA
1.5KE170CA
1.5KE180CA
1.5KE200CA
1.5KE220CA
1.5KE250CA
1.5KE300CA
1.5KE320CA
1.5KE350CA
1.5KE400CA
1.5KE440CA
1.5KE480CA
1.5KE510CA
1.5KE530CA
1.5KE540CA
1.5KE550CA
5.80
6.40
7.02
7.78
8.55
9.40
10.20
11.10
12.80
13.60
15.30
17.10
18.80
20.50
23.10
25.60
28.20
30.80
33.30
36.80
40.20
43.60
47.80
53.00
58.10
64.10
70.10
77.80
85.50
94.00
102.00
111.00
128.00
136.00
145.00
154.00
171.00
185.00
214.00
256.00
273.00
300.00
342.00
376.00
408.00
434.00
451.00
460.00
468.00
6.45
7.13
7.79
8.65
9.50
10.50
11.40
12.40
14.30
15.20
17.10
19.00
20.90
22.80
25.70
28.50
31.40
34.20
37.10
40.90
44.70
48.50
53.20
58.90
64.60
71.30
77.90
86.50
95.00
105.00
114.00
124.00
143.00
152.00
162.00
171.00
190.00
209.00
237.00
285.00
304.00
332.00
380.00
418.00
456.00
485.00
503.50
513.00
522.50
1.5KE600A
1.5KE600CA
512.00
570.00
Breakdown Voltage VBR
(Volts) @ IT
F
For bidirectional type having VR of 10 volts and less, the IR limit is double.
For parts without A, the VBR is ± 10% and VC is 5% higher than with A parts.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
I-V Curve Characteristics
Bi-directional
Uni-directional
Ipp
Vc VBR VR
V
IR VF
IT
IT
IR
Vc VBR VR
IR
IT
V
Ipp
Ipp
PPPM
VR
VBR
VC
IR
VF
VR VBR Vc
Peak Pulse Power Dissipation -- Max power dissipation
Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)
Reverse Leakage Current -- Current measured at VR
Forward Voltage Drop for Uni-directional
Ratings and Characteristic Curves (T =25°C unless otherwise noted)
A
Figure 1 - TVS Transients Clamping Waveform
Figure 2 - Peak Pulse Power Rating
100
PPPM-Peak Pulse Power (kW)
Voltage Transients
Voltage or Current
Voltage Across TVS
Current Through TVS
TJ initial = Tamb
1
0.1
0.001
Time
stacked-die, 2kW
at 10x1000µs, 25°C
10
Single die, 1.5kW
at 10x1000µs, 25°C
0.01
0.1
1
10
td-Pulse Width (ms)
continues on next page.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued)
A
Figure 4 - Pulse Waveform
Figure 3 - Peak Pulse Power Derating Curve
IPPM- Peak Pulse Current, % IRSM
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage %
150
100
75
50
25
0
0
25
50
75
100
125
150
175
tr=10µsec
2
50
10/1000µsec. Waveform
as defined by R.E.A
td
1.0
0
2.0
3.0
4.0
Figure 6 - Typical Transient Thermal Impedance
100
Transient Thermal Impedance (°C/W)
100000
Uni-directional V=0V
10000
Bi-directional V=0V
Cj(pF)
( )
t-Time (ms)
Figure 5 - Typical Junction Capacitance
1000
Uni-directional V=VR
100
Bi-directional V=VR
10
1
10
100
10
1
0.1
1000
0.01
VBR - Reverse Breakdown Voltage(V)
0.1
1
10
100
1000
TP - Pulse Duration (s)
Figure 7 - Maximum Non-Repetitive Peak Forward
Surge Current Uni-Directional Only
Figure 8 - Peak Forward Voltage Drop vs Peak Forward
Current (Typical Values)
100.0
200
Single die
180
IF- Peak Forward Current(A)
IFSM - Peak Forward Surge Current (A)
Half Value
IPPM IPPM
0
TJ - Initial Junction Temperature (ºC)
1
Peak Value
IPPM
100
200
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
160
140
120
100
80
60
40
Stacked-die
10.0
1.0
20
0
1
10
Number of Cycles at 60 Hz
100
0.1
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
VF-Peak Forward Voltage(V)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
Soldering Parameters
Lead–free
assembly
Pre Heat
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Ramp-up
TL
Average ramp up rate (Liquidus Temp (TA)
to peak
3°C/second max
TS(max) to TA - Ramp-up Rate
3°C/second max
Reflow
tp
TP
- Temperature (TA) (Liquidus)
217°C
- Time (min to max) (ts)
60 – 150 seconds
Temperature (T)
Reflow Condition
tL
Ts(max)
Ramp-down
Ts(min)
ts
Preheat
25˚C
t 25˚C to Peak
Time (t)
Peak Temperature (TP)
260
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Flow/Wave Soldering (Solder Dipping)
Ramp-down Rate
6°C/second max
Peak Temperature :
265OC
Time 25°C to peak Temperature (TP)
8 minutes Max.
Dipping Time :
10 seconds
Do not exceed
260°C
Soldering :
1 time
+0/-5
Critical Zone
TL to TP
°C
Environmental Specifications
Physical Specifications
Weight
0.045oz., 1.2g
High Temp. Storage
JESD22-A103
Case
JEDEC DO-201 molded plastic body
over passivated junction.
HTRB
JESD22-A108
Polarity
Color band denotes the cathode except
Bipolar.
Temperature Cycling
JESD22-A104
Terminal
Matte Tin axial leads, solderable per
JESD22-B102.
H3TRB
JESD22-A101
RSH
JESD22-B106
Dimensions
D
Cathode Band
(for Uni-directional products only)
A
C
A
Dimensions
B
DO-201
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15
A
Inches
Millimeters
Min
Max
Min
Max
1.000
-
25.40
-
B
0.285
0.375
7.20
9.50
C
0.038
0.042
0.96
1.07
D
0.190
0.210
4.80
5.30
Transient Voltage Suppression Diodes
Axial Leaded – 1500W > 1.5KE series
Part Numbering System
Part Marking System
OPTION CODE:
BLANK Reel Tape
-B Bulk Packaging
Cathode Band
TYPE CODE:
A Uni-Directional (5% VBR Voltage Tolerance)
CA Bi-Directional (5% VBR Voltage Tolerance)
Littelfuse Logo
(for Uni-directional
products only)
F
1.5KE xxx XX X
YYWW
Trace Code Marking
1.5KEXXX
VBR VOLTAGE CODE
(Refer to the Electrical Characteristics table)
YY:Year Code
WW: Week Code
Product Type
SERIES CODE
Packaging
Component
Package
Quantity
Packaging
Option
1.5KExxxXX
DO-201
1200
Tape & Reel
EIA STD RS-296
1.5KExxxXX-B
DO-201
500
BULK
Littelfuse Spec.
Part Number
Packaging Specification
Tape and Reel Specification
Off Center
either side 2.063+0.079/-0.039
(53.0+2.0/-1.0)
0.028(0.7)
2.56
(65.0)
0.047
(1.2)
0.394+/-0.020
(10.0+/-0.5)
13.0
(330.2)
0.236
(6.0)
Dimensions are in
inches/mm
3.0
(76.2)
0.68
(17.27)
2.75
(69.85)
Recess Depth Max. 0.75 (19.05)
Direction of Feed
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 11/20/15