Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series 3KP Series RoHS Pb e3 Description Uni-directional The 3KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 3000 W PD 7.0 W IFSM 300 A VF 3.5/5.0 V TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RθJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RθJA 40 °C/W Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2) (Note 1), (Note 4) Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 3) Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2.Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. 3.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 4. The PPPM of stacked-die parts is 4kW and please contact littelfuse for the detail stacked-die parts. Functional Diagram • 3000W peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Glass passivated chip junction in P600 package • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) •E SD protection of data lines in accordance with IEC 61000-4-2 •E FT protection of data lines in accordance with IEC 61000-4-4 • Low incremental surge resistance • Typical IR less than 2μA when VBR min>12V • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”, (9.5mm) lead length, 5 lbs., (2.3kg) tension • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Plastic package is flammability rated V-0 per Underwriters Laboratories • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion Datasheet Bi-directional Cathode Resources Samples Anode Uni-directional © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series Electrical Characteristics (T =25°C unless otherwise noted) A Breakdown Voltage VBR (Volts) @ IT Maximum Maximum Clamping Peak Voltage Pulse Current VC @ IPP IPP (A) (V) Maximum Reverse Leakage IR@ VR (µ A) Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) MIN MAX Test Current IT (mA) 3KP5.0A 3KP6.0A 3KP6.5A 3KP7.0A 3KP7.5A 3KP8.0A 3KP8.5A 3KP9.0A 3KP10A 3KP11A 3KP12A 3KP13A 3KP14A 3KP15A 3KP16A 3KP17A 3KP18A 3KP20A 3KP22A 3KP24A 3KP26A 3KP28A 3KP30A 3KP33A 3KP36A 3KP40A 3KP43A 3KP45A 3KP48A 3KP51A 3KP54A 3KP58A 3KP60A 3KP64A 3KP70A 3KP75A 3KP78A 3KP85A 3KP90A 3KP100A 3KP110A 3KP120A 3KP130A 3KP150A 3KP160A 3KP170A 3KP180A 3KP190A 3KP200A 3KP210A 3KP220A 3KP5.0CA 3KP6.0CA 3KP6.5CA 3KP7.0CA 3KP7.5CA 3KP8.0CA 3KP8.5CA 3KP9.0CA 3KP10CA 3KP11CA 3KP12CA 3KP13CA 3KP14CA 3KP15CA 3KP16CA 3KP17CA 3KP18CA 3KP20CA 3KP22CA 3KP24CA 3KP26CA 3KP28CA 3KP30CA 3KP33CA 3KP36CA 3KP40CA 3KP43CA 3KP45CA 3KP48CA 3KP51CA 3KP54CA 3KP58CA 3KP60CA 3KP64CA 3KP70CA 3KP75CA 3KP78CA 3KP85CA 3KP90CA 3KP100CA 3KP110CA 3KP120CA 3KP130CA 3KP150CA 3KP160CA 3KP170CA 3KP180CA 3KP190CA 3KP200CA 3KP210CA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 190.0 200.0 210.0 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 211.00 222.00 233.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 233.00 246.00 258.00 50 50 50 50 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 289.0 310.0 329.2 349.5 326.1 291.3 267.9 250.0 232.6 220.6 208.3 194.8 176.5 164.8 150.8 139.5 129.3 123.0 115.4 108.7 102.7 92.6 84.5 77.1 71.3 66.1 62.0 56.3 51.6 46.5 43.2 41.3 38.8 36.4 34.4 32.1 31.0 29.1 26.5 24.8 23.8 21.9 20.5 18.5 16.9 15.5 14.4 12.3 11.6 10.9 10.4 9.7 9.1 8.6 5000 5000 2000 1000 250 150 50 20 15 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 3KP220CA 220.0 244.00 270.00 5 371.1 8.1 2 X For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts For bidirectional type having VR of 10 volts and less, the IR limit is double. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Agency Approval Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR V IR VF IT IT IR Vc VBR VR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS stacked-die, 4kW at 10x1000µs, 25°C 10 Current Through TVS Single die, 3kW at 10x1000µs, 25°C 1 TJ initial = Tamb 0.1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) continues on next page. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 150 100 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 75 50 25 0 0 25 50 75 100 125 150 175 200 Half Value IPPM IPPM ( ) 2 50 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100000 100 10000 Transient Thermal Impedance (°C/W) Uni-direconal V=0V Bi-direconal V=0V Uni-direconal V=VR 1000 Bi-direconal V=VR 100 10 10 1 0.1 1 1 10 100 0.01 1000 0.1 1 10 100 1000 TP - Pulse Duration (s) VBR - Reverse Breakdown Voltage(V) Figure 7 - Maximum Non-Repetitive Peak Forward 500 Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 450 100 IF- Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 0 TJ - Initial Junction Temperature (ºC) Cj(pF) tr=10µsec 400 350 300 250 200 150 100 50 Single die 10 Stack-die 1 0.1 0 1 10 Number of Cycles at 60 Hz 100 0.01 0.00 1.00 2.00 3.00 4.00 5.00 6.00 VF-Peak Forward Voltage(V) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 7.00 8.00 Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series Soldering Parameters Lead–free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Ramp-up TL Average ramp up rate (Liquidus Temp (TA) to peak 3°C/second max TS(max) to TA - Ramp-up Rate 3°C/second max Reflow tp TP Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C - Temperature (TA) (Liquidus) 217°C - Time (min to max) (ts) 60 – 150 seconds Critical Zone TL to TP t 25˚C to Peak Time (t) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6°C/second max Peak Temperature : 265OC Time 25°C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 260°C Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.07oz., 2.1g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 Dimensions D Cathode Band (for Uni-directional products only) C A A B Dimensions Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 P600 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Transient Voltage Suppression Diodes Axial Leaded – 3000W > 3KP series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band (for Uni-directional products only) TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) F 3KPxxx XX X YYWW Trace Code Marking Littelfuse Logo 3KPXXX VR VOLTAGE Product Type SERIES CODE Packing Options Component Package Quantity Packaging Option 3KPxxxXX P600 800 Tape & Reel EIA STD RS-296 3KPxxxXX-B P600 100 BULK Littelfuse Spec. Part Number YY:Year Code WW: Week Code Packaging Specification Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15 Direction of Feed