Phase Control Using Thyristors

Teccor® brand Thyristors
AN1003
Phase Control Using Thyristors
It is important to note that the circuit current is determined
by the load and power source. For simplification, assume
the load is resistive; that is, both the voltage and current
waveforms are identical.
Introduction
Due to high-volume production techniques, Thyristors
are now priced so that almost any electrical product can
benefit from electronic control. A look at the fundamentals
of SCR and Triac phase controls shows how this is
possible.
Full-wave Rectified Operation
Voltage Applied to Load
Output Power Characteristics
Phase control is the most common form of Thyristor power
control. The Thyristor is held in the off condition -- that is, all
current flow in the circuit is blocked by the Thyristor except
a minute leakage current. Then the Thyristor is triggered
into an “on” condition by the control circuitry.
Delay (Triggering) Angle
Conduction Angle
For full-wave AC control, a single Triac or two SCRs
connected in inverse parallel may be used. One of two
methods may be used for full-wave DC control -- a bridge
rectifier formed by two SCRs or an SCR placed in series
with a diode bridge as shown in Figure AN1003.1.
Control
Circuit
Figure AN1003.2
Different loads respond to different characteristics of
the AC waveform. For example, some are sensitive to
average voltage, some to RMS voltage, and others to peak
voltage. Various voltage characteristics are plotted against
conduction angle for half- and full-wave phase control
circuits in Figure AN1003.3 and Figure AN1003.4.
Control
Circuit
Line
Load
Line
Two SCR AC Control
Sine Wave Showing Principles of Phase
Control
Load
Triac AC Control
θ
HALF WAVE
Line
Line
1.8
Control
Circuit
Control
Circuit
Load
One SCR DC Control
Figure AN1003.1
Normalized Sine Wave RMS Voltage Power
as Fraction of Full Conduction
1.6
Load
Two SCR DC Control
SCR/Triac Connections for Various Methods
of Phase Control
Figure AN1003.2 illustrates voltage waveform and shows
common terms used to describe Thyristor operation. Delay
angle is the time during which the Thyristor blocks the line
voltage. The conduction angle is the time during which the
Thyristor is on.
Peak Voltage
1.4
1.2
1.0
RMS
0.8
Power
0.6
0.4
0.2
AVG
0
0
20
40
60
80
100 120 140 160 180
Conduction Angle (θ)
Figure AN1003.3
Phase Control Using Thyristors
401
Half-Wave Phase Control (Sinusoidal)
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
θ
FULL WAVE
360 180
1.8
320 160
1.6
Peak Voltage
Peak Voltage
280 140
1.4
240 120
1.2
RMS
Output Voltage
Normal Sine Wave RMS Voltage Power
as Fraction of Full Conduction
θ
HALF WAVE
Input
Voltage
230 V 115 V
θ
1.0
Power
0.8
0.6
0.4
200 100
RMS
160
80
120
60
80
40
40
20
0
0
AVG
AVG
0.2
0
0
20
40
60
80
100 120 140 160 180
0
20
40
Figure AN1003.4
60
80
100 120 140 160 180
Conduction Angle (θ)
Conduction Angle (θ)
Symmetrical Full-Wave Phase Control
(Sinusoidal)
Figure AN1003.5
Figure AN1003.3 and Figure AN1003.4 also show the
relative power curve for constant impedance loads such as
heaters. Because the relative impedance of incandescent
lamps and motors change with applied voltage, they do
not follow this curve precisely. To use the curves, find the
full-wave rated power of the load, and then multiply by the
ratio associated with the specific phase angle. Thus, a 180º
conduction angle in a half-wave circuit provides 0.5 x fullwave conduction power.
Output Voltage of Half-wave Phase
θ
FULL WAVE
Input
Voltage
230 V 115 V
360 180
θ
320 160
Peak Voltage
280 140
240 120
Output Voltage
In a full-wave circuit, a conduction angle of 150º provides
97% full power while a conduction angle of 30º provides
only 3% of full power control. Therefore, it is usually
pointless to obtain conduction angles less than 30º or
greater than 150º.
Figure AN1003.5 and Figure AN1003.6 give convenient
direct output voltage readings for 115 V/230 V input voltage.
These curves also apply to current in a resistive circuit.
RMS
200 100
160
80
120
60
80
40
40
20
0
0
AVG
0
20
40
60
80
100 120 140 160 180
Conduction Angle (θ)
Figure AN1003.6
Phase Control Using Thyristors
402
Output Voltage of Full-wave Phase Control
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
charging resistance needed to obtain the desired control
characteristics.
Control Characteristics
A relaxation oscillator is the simplest and most common
control circuit for phase control. Figure AN1003.7 illustrates
this circuit as it would be used with a Thyristor. Turn-on
of the Thyristor occurs when the capacitor is charged
through the resistor from a voltage or current source until
the breakover voltage of the switching device is reached.
Then, the switching device changes to its on state, and the
capacitor is discharged through the Thyristor gate. Trigger
devices used are neon bulbs, unijunction transistors, and
three-, four-, or five-layer semiconductor trigger devices.
Phase control of the output waveform is obtained by
varying the RC time constant of the charging circuit so the
trigger device breakdown occurs at different phase angles
within the controlled half or full cycle.
Many circuits begin each half-cycle with the capacitor
voltage at or near zero. However, most circuits leave a
relatively large residual voltage on the capacitor after
discharge. Therefore, the charging resistor must be
determined on the basis of additional charge necessary to
raise the capacitor to trigger potential.
For example, assume that we want to trigger an S2010L
SCR with a 32 V trigger DIAC. A 0.1 µF capacitor will supply
the necessary SCR gate current with the trigger DIAC.
Assume a 50 V dc power supply, 30º minimum conduction
angle, and 150º maximum conduction angle with a 60
Hz input power source. At approximately 32 V, the DIAC
triggers leaving 0.66 VBO of DIAC voltage on the capacitor.
In order for DIAC to trigger, 22 V must be added to the
capacitor potential, and 40 V additional (50-10) are available.
The capacitor must be charged to 22/40 or 0.55 of the
available charging voltage in the desired time. Looking at
Figure AN1003.8, 0.55 of charging voltage represents 0.8
time constant. The 30º conduction angle required that the
firing pulse be delayed 150º or 6.92 ms. (The period of 1/2
cycle at 60 Hz is 8.33 ms.) To obtain this time delay:
Switching
Device
R
Voltage
or
Current
Source
SCR
Triac
C
Figure AN1003.7
6.92 ms = 0.8 RC
Relaxation Oscillator Thyristor Trigger Circuit
RC = 8.68 ms
Figure AN1003.8 shows the capacitor voltage-time
characteristic if the relaxation oscillator is to be operated
from a pure DC source.
if C = 0.10 µF
8.68 x 10–3
then, R =
= 86,000 Ω
0.1 x 10–6
To obtain the minimum R (150º conduction angle), the
delay is 30º or
1.0
Ratio of
(
Capacitor Voltage
Supply Source Voltage
)
0.9
0.8
(30/180) x 8.33 = 1.39 ms
0.7
1.39 ms = 0.8 RC
0.6
C = 1.74 ms
R
1.74 x 10–3
R=
= 17,400 Ω
0.1 x 10–6
0.5
0.4
0.3
Using practical values, a 100 k potentiometer with up
to 17 k minimum (residual) resistance should be used.
Similar calculations using conduction angles between the
maximum and minimum values will give control resistance
versus power characteristic of this circuit.
0.2
0.1
0
0
1
2
3
4
5
6
Time Constants
Figure AN1003.8
Triac Phase Control
Capacitor Charging from DC Source
The basic full-wave Triac phase control circuit shown
in Figure AN1003.9 requires only four components.
Adjustable resistor R1 and C1 are a single-element phaseshift network. When the voltage across C1 reaches
breakover voltage (VBO) of the DIAC, C1 is partially
discharged by the DIAC into the Triac gate. The Triac is then
triggered into the conduction mode for the remainder of
that half-cycle. In this circuit, triggering is in Quadrants I
and III. The unique simplicity of this circuit makes it suitable
for applications with small control range.
Usually, the design starting point is the selection of a
capacitance value which will reliably trigger the Thyristor
when the capacitance is discharged. Trigger devices and
Thyristor gate triggering characteristics play a part in the
selection. All the device characteristics are not always
completely specified in applications, so experimental
determination is sometimes needed.
Upon final selection of the capacitor, the curve shown
in Figure AN1003.8 can be used in determining the
Phase Control Using Thyristors
403
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
Load
R1
Load
Quadrac
(Q4010LT)
250 k
R4
100
R2
120 V
(60 Hz)
R2
3.3 k
C1
0.1 µF
Figure AN1003.9
Figure AN1003.11
The hysteresis (snap back) effect is somewhat similar to
the action of a kerosene lantern. That is, when the control
knob is first rotated from the off condition, the lamp can be
lit only at some intermediate level of brightness, similar to
turning up the wick to light the lantern. Brightness can then
be turned down until it finally reaches the extinguishing
point. If this occurs, the lamp can only be relit by turning
up the control knob again to the intermediate level. Figure
AN1003.10 illustrates the hysteresis effect in capacitorDIAC triggering. As R1 is brought down from its maximum
resistance, the voltage across the capacitor increases
until the DIAC first fires at point A, at the end of a halfcycle (conduction angle θi). After the gate pulse, however,
the capacitor voltage drops suddenly to about half the
triggering voltage, giving the capacitor a different initial
condition. The capacitor charges to the DIAC, triggering
voltage at point B in the next half-cycle and giving a steadystate conduction angle shown as θ for the Triac.
AC Line
C1
0.1 µF
(a)
Extended Range Full-wave Phase Control
R2
D1
R3
3.3 k
R1
250 k
C1
0.1 µF
D2
Quadrac
(Q4010LT)
Diac
D1, D2 = 400 V Diodes
Load
(b)
R2
D2
θi
R1 = 250 k POT
R2, R3 = 15 k, 1/2 W
Relationship of AC Line Voltage and
Triggering Voltage
Figure AN1003.12
In the Figure AN1003.11 illustration, the addition of a
second RC phase-shift network extends the range on
control and reduces the hysteresis effect to a negligible
region. This circuit will control from 5% to 95% of full load
power, but is subject to supply voltage variations. When R1
is large, C1 is charged primarily through R3 from the phaseshifted voltage appearing across C2. This action provides
additional range of phase-shift across C1 and enables C2
to partially recharge C1 after the DIAC has triggered, thus
reducing hysteresis. R3 should be adjusted so that the
circuit just drops out of conduction when R1 is brought to
maximum resistance.
R3
D1
[–Diac VBO]
Diac Does Not
Trigger at "A"
R4
Quadrac
(Q4010LT)
R1
120 V
(60 Hz)
B
Phase Control Using Thyristors
15 k
1/2 W
120 V
(60 Hz)
A
Figure AN1003.10
Diac
Load
[+Diac VBO]
Capacitor
Voltage
250 k
By using one of the circuits shown in Figure AN1003.12,
the hysteresis effect can be eliminated entirely. The circuit
(a) resets the timing capacitor to the same level after each
positive half-cycle, providing a uniform initial condition for
the timing capacitor. This circuit is useful only for resistive
loads since the firing angle is not symmetrical throughout
the range. If symmetrical firing is required, use the circuit
(b) shown in Figure AN1003.12.
θ
Diac Triggers at "A"
Quadrac
(Q4010LT)
100 k
Trim
C2
0.1 µF
Basic DIAC-Quadrac Phase Control
R1
R3
0.1 µF
Diac
68 k
120 V
(60 Hz)
(For Inductive
Loads)
3.3 k
D3
C1
0.1 µF
D4
Diac
R4 = 3.3 k
D1, D2, D3, D4 = 400 V Diodes
Wide-range Hysteresis Free Phase Control
For more complex control functions, particularly closed
loop controls, the unijunction transistor may be used for
the triggering device in a ramp and pedestal type of firing
circuit as shown in Figure AN1003.13.
404
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
L1
Ramp
UJT Triggering Level
Pedestal
UJT Emitter Voltage
Cool
R2
3.3 k
C1
Hot
0
Load
Time
D1
D2
R6
R2
R3
D3
D5
D4
R5
Temp
R4 T
R1, R2 = 2.2 k, 2 W
R3 = 2.2 k, 1/2 W
R4 = Thermistor, approx. 5 k
at operating temperature
R5 = 10 k Potentiometer
R6 = 5 M Potentiometer
R7 = 100 k, 1/2 W
R8 = 1 k, 1/2 W
Figure AN1003.13
"Gain"
R8
Q1
0.1 µF
C3 *
Diac
100 V
Q2
Triac
Note: L1 and C1 form an
RFI filter that may be eliminated
C1
AC
AC
Input
Load
Voltage Current
T1
Q1 = 2N2646
Q2 = Q4010L5
T1 = Dale PT 10-101
or equivalent
D1-4 = 200 V Diode
D5 = 20 V Zener
D6 = 100 V Diode
C1 = 0.1 µF, 30 V
R1
C1, C3
L1
Q1
12 A
250 k
0.1 µF 200 V
100 µH
Q4010LTH
240 V ac
50/60 Hz
3A
500 k
0.1 µF 400 V
200 µH
Q6006LTH
Figure AN1003.14
Several speed control and light dimming (phase) control
circuits have been presented that give details for a
complete 120 V application circuit but none for 240 V.
Figure AN1003.14 and Figure AN1003.15 show some
standard phase control circuits for 240 V, 60 Hz/50 Hz
operation along with 120 V values for comparison. Even
though there is very little difference, there are a few key
things that must be remembered. First, capacitors and
Triacs connected across the 240 V line must be rated at
400 V. Secondly, the potentiometer (variable resistor) value
must change considerably to obtain the proper timing or
triggering for 180º in each half-cycle.
* dv/dt snubber network
when required
120 V ac
60 Hz
Precision Proportional Temperature Control
Single-time-constant Circuit for Incandescent
Light Dimming, Heat Control, and Motor
Speed Control
The circuit shown in Figure AN1003.15 is a doubletime-constant circuit which has improved performance
compared to the circuit shown in Figure AN1003.14. This
circuit uses an additional RC network to extend the phase
angle so that the Triac can be triggered at small conduction
angles. The additional RC network also minimizes any
hysteresis effect explained and illustrated in Figure
AN1003.10 and Figure AN1003.11.
L1
Load
R1
3.3 k
Figure AN1003.14 shows a simple single-time-constant
light dimmer (phase control) circuit, giving values for both
120 V and 240 V operation.
AC
Input
15 k
1/2 W
0.1 µF
100 V
C3
Note: L1 and C1 form an
RFI filter that may be eliminated
AC
AC
Input
Load
Voltage Current
C4 *
Diac
* dv/dt snubber network
when required
R2
C1, C2, C4
L1
Q1
120 V ac
60 Hz
8A
250 k
0.1 µF 200 V
100 µH
Q4010LTH
240 V ac
50 Hz
6A
500 k
0.1 µF 400 V
200 µH
Q6008LTH
240 V ac
60 Hz
6A
500 k
0.1 µF 400 V
200 µH
Q6008LTH
Figure AN1003.15
405
100
Q1
R3
R2
C1
R4 *
C2
Phase Control Using Thyristors
100
Q1
C2
R7
D6
R3 *
R1
AC
Input
R1
120 V
(60 Hz)
Load
Double-time-constant Circuit for
Incandescent Light Dimming, Heat Control,
and Motor Speed Control
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
Permanent Magnet Motor Control
Load
Figure AN1003.16 illustrates a circuit for phase controlling
a permanent magnet (PM) motor. Since PM motors
are also generators, they have characteristics that
make them difficult for a standard Triac to commutate
properly. Control of a PM motor is easily accomplished
by using an alternistor Triac with enhanced commutating
characteristics.
R1
SCR1
2.2 k
R2
AC
Input
CR1
R3
+
DC
MTR
3.3 k
-
100
Q4006LTH
15 k 1/2 W
T
Diac
0.1 µF
400 V
R2
CR1
SCR1
R3
MT2
120 V ac
60 Hz
0.8 A
500 k
IN4003
EC103D
1k
MT1
120 V ac
60 Hz
8.5 A
100 k
IN4003
S4010R
Not
Required
240 V ac
60 Hz
0.8 A
1M
IN4004
EC103D
1k
240 V ac
60 Hz
8.5 A
250 k
IN4004
S6010R
Not
Required
240 V ac
50Hz
2.5 A
1M
IN4004
T106M1
1k
250 k
115 V ac
Input
Figure AN1003.16
AC
AC
Input
Load
Voltage Current
1.5 A
0.1 µF
400 V
0.1 µF
100 V
Circuit for Phase Controlling a Permanent
Magnet Motor
PM motors normally require full-wave DC rectification.
Therefore, the alternistor Triac controller should be
connected in series with the AC input side of the rectifier
bridge. The possible alternative of putting an SCR controller
in series with the motor on the DC side of the rectifier
bridge can be a challenge when it comes to timing
and delayed turn-on near the end of the half cycle. The
alternistor Triac controller shown in Figure AN1003.16
offers a wide range control so that the alternistror Triac
can be triggered at a small conduction angle or low motor
speed; the rectifiers and alternistors should have similar
voltage ratings, with all based on line voltage and actual
motor load requirements.
Figure AN1003.17
Half-wave Control, 0º to 90º Conduction
Figure AN1003.18 shows a half-wave phase control circuit
using an SCR to control a universal motor. This circuit is
better than simple resistance firing circuits because the
phase-shifting characteristics of the RC network permit
the firing of the SCR beyond the peak of the impressed
voltage, resulting in small conduction angles and very slow
speed.
Universal Motor
M
SCR Phase Control
R1
3.3 k
Figure AN1003.17 shows a very simple variable resistance
half-wave circuit. It provides phase retard from essentially
zero (SCR full on) to 90 electrical degrees of the anode
voltage wave (SCR half on). Diode CR1 blocks reverse gate
voltage on the negative half-cycle of anode supply voltage.
This protects the reverse gate junction of sensitive SCRs
and keeps power dissipation low for gate resistors on the
negative half cycle. The diode is rated to block at least
the peak value of the AC supply voltage. The retard angle
cannot be extended beyond the 90-degree point because
the trigger circuit supply voltage and the trigger voltage
producing the gate current to fire are in phase. At the peak
of the AC supply voltage, the SCR can still be triggered
with the maximum value of resistance between anode and
gate. Since the SCR will trigger and latch into conduction
the first time IGT is reached, its conduction cannot be
delayed beyond 90 electrical degrees with this circuit.
Phase Control Using Thyristors
AC
Supply
D-30A
R2
SCR1
CR1
Diac
C1
AC
AC
Input
Load
Voltage Current
CR1
SCR1
C1
120 V ac
60 Hz
8A
150 k
IN4003
S6008L
0.1µF 200 V
240 V ac
60 Hz
6.5 A
200 k
IN4004
S4015L
0.1µF 400 V
240 V ac
50 Hz
6.5 A
200 k
IN4004
S6008L
0.1µF 400 V
Figure AN1003.18
406
R2
Half-wave Motor Control
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
For a circuit to control a heavy-duty inductive load where
an alternistor is not compatible or available, two SCRs can
be driven by an inexpensive TO-92 Triac to make a very high
current Triac or alternistor equivalent, as shown in Figure
AN1003.21. See ”Relationship of IAV, IRMS, and IPK’ in
AN1009 for design calculations.
Phase Control from Logic (DC) Inputs
Triacs can also be phase-controlled from pulsed DC
unidirectional inputs such as those produced by a digital
logic control system. Therefore, a microprocessor can be
interfaced to AC load by using a sensitive gate Triac to
control a lamp’s intensity or a motor’s speed.
Hot
There are two ways to interface the unidirectional logic
pulse to control a Triac. Figure AN1003.19 illustrates one
easy way if load current is approximately 5 A or less.
The sensitive gate Triac serves as a direct power switch
controlled by HTL, TTL, CMOS, or integrated circuit
operational amplifier. A timed pulse from the system’s
logic can activate the Triac anywhere in the AC sinewave
producing a phase-controlled load.
VDD = 15 VDC
VDD
Sensitive Gate
Triac
OV
16
G
G
OR
A
K
K
A
G Non-sensitive
Gate SCRs
MT1
Gate Pulse
Input
Neutral
Figure AN1003.21
Triac Driving Two Inverse Parallel NonSensitive Gate SCRs
Figure AN1003.22 shows another way to interface a
unidirectional pulse signal and activate AC loads at various
points in the AC sine wave. This circuit has an electricallyisolated input which allows load placement to be flexible
with respect to AC line. In other words, connection
between DC ground and AC neutral is not required.
120 V
60 Hz
MT1
G
8
MT2
Triac
Hot
Load
MT2
Load
Neutral
Rin
Figure AN1003.19
Timed
Input
Pulse
Sensitive Gate Triac Operating in
Quadrants I and IV
1
6
2
4
100
100
0.1 µF
250 V
C1
G
The key to DC pulse control is correct grounding for DC
and AC supply. As shown in Figure AN1003.19, DC ground
and AC ground/neutral must be common plus MT1
must be connected to common ground. MT1 of the Triac
is the return for both main terminal junctions as well as the
gate junction.
Figure AN1003.22 Opto-isolator Driving a Triac or Alternistor Triac
Microcontroller Phase Control
Traditionally, microcontrollers were too large and expensive
to be used in small consumer applications such as a light
dimmer. Microchip Technology Inc. of Chandler, Arizona
has developed a line of 8-pin microcontrollers without
sacrificing the functionality of their larger counterparts.
These devices do not provide high drive outputs, but when
combined with a sensitive Triac can be used in a costeffective light dimmer.
R3
G
T
115 V ac
220 V ac
Z
+
R5
8
C2
7
TRIG VSS
6
R6
5
EXT
SENS
Touch
Plate
LS7631 / LS7632
R1
R2
N
Figure AN1003.23 illustrates a simple circuit using a
transformerless power supply, PIC 12C508 microcontroller,
and a sensitive Triac configured to provide a light dimmer
control. R3 is connected to the hot lead of the AC power
line and to pin GP4. The ESD protection diodes of the input
structure allow this connection without damage. When the
voltage on the AC power line is positive, the protection
diode form the input to VDD is forward biased, and the input
buffer will see approximately VDD + 0.7 V. The software
will read this pin as high. When the voltage on the line is
negative, the protection diode from VSS to the input pin is
forward biased, and the input buffer sees approximately
VSS - 0.7 V. The software will read the pin as low. By polling
GP4 for a change in state, the software can detect zero
crossing.
C5
D1
L
C1
NOTE: As a precaution,
transformer should have
thermal protection.
VDD MODE
CAP
SYNC
1
3
4
2
C3
R4
C4
Halogen
Lamp
115 V ac
C1 = 0.15 µF, 200 V
C2 = 0.22 µF, 200 V
C3 = 0.02 µF, 12 V
C4 = 0.002 µF, 12 V
C5 = 100 µF, 12 V
R1 = 270, ¼ W
R2 = 680 k, ¼ W
220 V ac
R3 = 62, ¼ W
R4 = 1 M to 5 M, ¼ W
(Selected for sensitivity)
R5, R6 = 4.7 M, ¼ W
D1 = 1N4148
Z = 5.6 V, 1 W Zener
T = Q4006LH4 Alternistor
L = 100 µH (RFI Filter)
Figure AN1003.20
C1 = 0.15 µF, 400 V
C2 = 0.1 µF, 400 V
C3 = 0.02 µF, 12 V
C4 = 0.002 µF, 12 V
C5 = 100 µF, 12 V
R1 = 1 k, ¼ W
R2 = 1.5 M, ¼ W
R3 = 62, ¼ W
R4 = 1 M to 5 M, ¼ W
(Selected for sensitivity)
R5, R6 = 4.7 M, ¼ W
D1 = 1N4148
Z = 5.6 V, 1 W Zener
T = Q6006LH4 Alternistor
L = 200 µH (RFI Filter)
Typical Touch Plate Halogen Lamp Dimmer
Phase Control Using Thyristors
Triac or
Alternistor
Triac
Neutral
L
MT2
MT1
Hot
120 V
60 Hz
Load could be here
instead of upper location
Figure AN1003.20 shows an example of a unidirectional
(all negative) pulse furnished from a special I.C. that
is available from LSI Computer Systems in Melville,
New York. Even though the circuit and load is shown to
control a Halogen lamp, it could be applied to a common
incandescent lamp for touch-controlled dimming.
MT1
Load
MT2
407
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
C3
0.1 µF
R1
47
120 V ac
(High)
D1
1N4001
R2
1M
RV1
Varistor
VDD
D1
1N4001
D3
1N5231
C1
220 µF
C2
0.01 µF
AC
(Return)
White
+5 V
150 W
Lamp
R3
20 M
VDD
VSS
GP5
GP0
GP4
GP1
GP3
GP2
Q1
L4008L5
R6
470
12C508
Remote
Switch
Connector
JP1
U1
Dim
S1
R4
470
Bright
S2
R5
470
3
2
1
Figure AN1003.23
Microcontroller Light Dimmer Control
With a zero crossing state detected, software can be
written to turn on the Triac by going from tri-state to a logic
high on the gate and be synchronized with the AC phase
cycles (Quadrants I and IV). Using pull-down switches
connected to the microcontoller inputs, the user can signal
the software to adjust the duty cycle of the Triac.
For higher amperage loads, a small 0.8 A, TO-92 Triac
(operating in Quadrants I and IV) can be used to drive
a 25 A alternistor Triac (operating in Quadrants I and
III) as shown in the heater control illustration in Figure
AN1003.24.
For a complete listing of the software used to control this
circuit, see the Microchip application note PICREF-4. This
application note can be downloaded from Microchip’s Web
site at www.microchip.com.
Phase Control Using Thyristors
408
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13
Teccor® brand Thyristors
AN1003
C3
.1µF
R1
47
120VAC
(HIGH)
D1
1N4001
R2
1M
RV1
VARISTOR
VDD
D1
1N4001
D3
1N5231
C1
220µF
C2
.01µF
AC
(RETURN)
WHITE
+5V
2000 W
R3
20M
U1
VDD
VSS
GP5
GP0
GP4
GP1
GP3
R7
100Ω
Q1
L4X8E5
Q2
Q4025L6
R6
470
GP2
12C508
DECREASE HEAT
S1
S2
R4
470
R5
470
INCREASE HEAT
Figure AN1003.24
Microcontroller Heater Control
Summary
The load currents chosen for the examples in this
application note were strictly arbitrary, and the component
values will be the same regardless of load current except
for the power Triac or SCR. The voltage rating of the power
Thyristor devices must be a minimum of 200 V for 120 V
input voltage and 400 V for 240 V input voltage.
The use of alternistors instead of Triacs may be much more
acceptable in higher current applications and may eliminate
the need for any dv/dt snubber network.
For many electrical products in the consumer market,
competitive Thyristor prices and simplified circuits make
automatic control a possibility. These simple circuits
give the designer a good feel for the nature of Thyristor
circuits and their design. More sophistication, such as
speed and temperature feedback, can be developed as the
control techniques become more familiar. A remarkable
phenomenon is the degree of control obtainable with very
simple circuits using Thyristors. As a result, industrial and
consumer products will greatly benefit both in usability and
marketability.
Phase Control Using Thyristors
409
©2013 Littelfuse, Inc
Specifications are subject to change without notice.
Revised: 09/23/13