SIDACtor ® Protection Thyristors SLIC Protection Battrax® Series Single Port Positive/Negative - MS-013 RoHS Pb e3 Description The Single Port Positive/Negative Battrax® Series are programmable SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. This series is designed specifically to protect SLIC devices utilizing positive and negative ringing signals. This one device will protect a single port. Features and Benefits Agency Approvals Agency • Low voltage overshoot • Low capacitance • Low on-state voltage • Positive and negative ringing compatible • Does not degrade surge capability after multiple surge events within limit. Agency File Number E133083 • Fails short circuit when surged in excess of ratings Pinout Designation 1 6 2 5 3 • Single-port protect • Gate trgger tracking device • 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Applicable Global Standards 4 Schematic Symbol • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 • ITU K.20/21 Enhanced Level • YD/T 1082 • YD/T 993 • ITU K.20/21 Basic Level • YD/T 950 • GR 1089 Inter-building 6 (Ground) (T) 1 (-VREF) 2 5 (+VREF) (R) 3 4 (Ground) Electrical Characteristics Part Number Marking VDRM @lDRM=5µA VS @100V/µs V min V max IH IS mA min mA max IT VT @IT=2.2 Amps Capacitance* A max V max pF min pF max B3104UCLxx B3104UC I±VREFI + I±1.2VI I±VREFI + I±10VI 100 100 2.2 4 30 200 B3164UCLxx B3164UC I±VREFI + I±1.2VI I±VREFI + I±10VI 160 100 2.2 4 30 200 B3204UCLxx B3204UC I±VREFI + I±1.2VI I±VREFI + I±10VI 200 100 2.2 4 30 200 - VREF Max Value for the negative Battrax is -200 V. - VREF Max Value for the positive Battrax is +110 V. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional - All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 4 & 6) and Ring (pin 3) to Ground (pin 4 & 6) © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 * Off-state capacitance (CO) is measured across pins 1 & 4,6 and 3 & 4,6 at 1 MHz with a 2V bias. 1 Battrax® Series Single Port Positive/Negative, MS-013 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 200 50 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 C Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC (IPP rating assumes VREF equals +/- 48 V) - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Modified MS-013 6 5 4 Parameter Value Unit TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C 60 °C/W 1 2 R0JA 3 Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform VDRM IH VS IPP VREF -VREF VDRM VT IS -V IDRM IS IT IPP VS IPP – Peak Pulse Current – %IPP +I IDRM +V IH 100 Waveform = tr x td 50 Half Value 0 0 -I Normalized VS Change vs. Junction Temperature tr = rise time to peak value td = decay time to half value Peak Value td tr t – Time (µs) Normalized DC Holding Current vs. Case Temperature IH 8 6 25 °C 4 IH (TC = 25ºC) 10 Ratio of Percent of VS Change – % 2.0 14 12 2 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 25°C 1.2 2 Battrax® Series Single Port Positive/Negative, MS-013 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP Critical Zone TL to TP TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material tP Ramp-up Temperature Reflow Condition UL recognized epoxy meeting flammability classification 94V-0 Battrax Series Single Port Pos-Neg MS-013 Part Numbering.eps For pg. 135 High Temp Voltage Blocking 80% Rated VDRM (VDC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 MS-013 Part Marking Drawing_2009-03-05.eps Part Numbering Part Marking B3 xx 4 U C L xx TYPE B3: Dual (Positive & Negative Battrax SIDACtor) PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXX RoHS COMPLIANT Date Code HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 Part Marking Code (Refer to Electrical Characteristics Table) XXXXX IPP RATING PACKAGE TYPE 3 Battrax® Series Single Port Positive/Negative, MS-013 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7º TYP J 7º TYP A G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F 7º TYP MIN Length of Flat K Detail A B A B C D E F G H J K BSC* Inches Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/07/14 .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A 20.000 ± .030 (508.00 ± 0.76) .110 (2.79) A Dimensions are in inches (and millimeters) 4 Battrax® Series Single Port Positive/Negative, MS-013