SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) T10A Series - DO-15 RoHS Pb e3 Description T10A Series are SIDACtor® thyristors designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a cost effective through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits • Low voltage overshoot surged in excess of ratings • Low on-state voltage Agency File Number • Does not degrade surge capability after multiple surge events within limit. E128662 (68V-270V) • RoHS Compliant Agency Approvals Agency • Low capacitance • Pb-free means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Fails short circuit when Applicable Global Standards Pinout Designation Not Applicable • TIA-968-A • GR 1089 Intra-building • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21/45 Enhanced Level* Schematic Symbol • YD/T 1082 • ITU K.20/21/45 Basic Level • YD/T 993 • YD/T 950 • GR 1089 Inter-building* *A-rated parts require series resistance Electrical Characteristics Part Number T10A060Bxx T10A060Exx T10A062xx T10A068xx T10A080Bxx T10A080Exx T10A100xx T10A110Bxx T10A110Exx T10A120xx T10A130xx T10A140Bxx T10A140Exx T10A180xx T10A180Bxx T10A180Exx T10A200xx T10A220xx Marking T10A060B T10A060E T10A062 T10A068 T10A080B T10A080E T10A100 T10A110B T10A110E T10A120 T10A130 T10A140B T10A140E T10A180 T10A180B T10A180E T10A200 T10A220 VDRM @lDRM=5µA VS @100V/µs V Min V Max 50 50 56 61 70 70 90 100 100 108 117 120 120 170 170 170 180 200 84 84 86 94 125 125 140 142 142 168 178 178 178 220 220 220 275 275 IH IS mA Min mA Max 120 180 150 150 120 180 150 120 180 150 150 120 180 150 120 180 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT @IT=2.2 Amp Capacitance @ 1MHz, 2V Bias A Max V Max pF Typ 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 50 50 50 50 43 43 43 38 38 38 38 34 34 34 32 32 30 30 Table continues on next page. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/09/16 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) Part Number Marking T10A220Bxx T10A220Exx T10A240xx T10A270xx T10A270Bxx T10A270Exx T10A220B T10A220E T10A240 T10A270 T10A270B T10A270E VDRM @lDRM=5µA VS @100V/µs V Min V Max 200 200 216 245 245 245 275 275 330 370 370 370 IH IS mA Min mA Max 120 180 150 150 120 180 800 800 800 800 800 800 IT VT @IT=2.2 Amp Capacitance @ 1MHz, 2V Bias A Max V Max pF Typ 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 30 30 30 30 30 30 Notes: • Absolute maximum ratings measured at TA= 25ºC. • Components are bi-directional (unless otherwise noted). • XX Part Number Suffis: “RP” (Reel Pack) or Blank (Bulk Pack) Surge Ratings IPP Series A ITSM 50/60 Hz di/dt A min A min A/µs max 50 20 100 8/20 1.2/502 5/3101 10/7002 10/10001 10/10002 A min A min 100 37.5 1 Notes: 1 Current waveform in µs 2 Voltage waveform in µs - Peak pulse current rating (IPP) is repetitive and guaranteed of the product in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Parameter Value Unit DO-15 TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 120 °C/W V-I Characteristics tr x td Pulse Waveform IT IS IH -V IDRM +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/09/16 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 °C 4 1.8 IH (TC = 25ºC) 12 1.6 1.4 2 0 -4 25°C 1.2 1.0 Ratio of Percent of VS Change – % 14 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Lead Material Figure 1 TP TL TS(max) 100% Matte-Tin Plated Body Material UL Recognized epoxy meeting flammability classification V-0 Critical Zone TL to TP tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Copper Alloy Terminal Finish tP Ramp-up Temperature Reflow Condition © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/09/16 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Numbering Part Marking T10A xxx x xx (Refer to Electrical Characteristics Table) T10Axxxx PACKING OPTIONS Blank: Bulk RP: Reel Pack MEDIAN VOLTAGE HOLDING CURRENT: Blank: 150mA B: 120mA Dimensions - DO-15 (Revised 11/14/07) E: 180mA XXXXX TYPE T10A = SIDACtor T10A series Part Marking Code Date Code Dimensions — DO-15 B L Inches Dimension D G L Millimeters MIN MAX MIN MAX B 0.028 0.034 0.711 0.864 D 0.12 0.14 3.048 3.556 G 0.235 0.27 5.969 6.858 L 1 25.4 Packing Options Package Type T10A Description Packaging Quantity Added Suffix Industry Standard DO-15 Tape and Reel Pack 1000 RP EIA-RS-296-D DO-15 Bulk Pack 500 N/A N/A Tape and Reel Specification— DO-15 A Spacing off center, either side 0.039 (1.0) 2.55 (64.8) B TYP C E D Dimensions are in inches (and millimeters). Symbols Description Inches MM A Component Spacing (lead to lead) 0.200 ± 0.020” 5.08 ± 0.508 B C D E F G Inner Tape Pitch Tape Width Max. Off Alignment Reel Dimension Max. Hub Recess Max. Abor Hole 2.062 ± 0.059” 0.250” 0.048” 13” 3” 0.68” 52.37 ± 1.498 6.35 1.219 330.2 76.19 17.27 Additional Information 3.15 (80.0) TYP Datasheet recess depth max 0.75” G F Resources Samples Direction of Feed © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/09/16