SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Series - DO-214 Description Fixed Voltage Series DO-214 are uni-directional SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single line protection using a fixed voltage switching device for negative surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits t Low voltage overshoot t Low on-state voltage Agency Approvals Agency t Does not degrade with use Agency File Number E133083 t Integrated diode for positive voltage surges Applicable Global Standards Pinout Designation Indicates cathode t TIA-968-A t GR 1089 Intra-building* t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* Schematic Symbol (T/R) t Fails short circuit when surged in excess of ratings *A-rated parts require series resistance (G) Electrical Characteristics Part Number P0641SALRP P0721SALRP P0901SALRP P1101SALRP P1301SALRP P1701SALRP P0641SCLRP P0721SCLRP P0901SCLRP P1101SCLRP P1301SCLRP P1701SCLRP Marking P61A P71A P91A P01A P131A P17A P61C P71C P91C P01C P131C P17C VDRM @lDRM=5μA VS @100V/μs IH IS IT VT @IT=2.2 Amps VF V min V max mA min mA max A max V max V max 58 65 75 95 120 160 58 65 75 95 120 160 77 88 98 130 160 200 77 88 98 130 160 200 120 120 120 120 120 120 120 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 89 Revised: February 22, 2011 Capacitance @1MHz, -2V bias pF pF min pF max 50 45 45 40 40 30 65 60 60 50 50 40 90 85 80 70 70 55 200 190 180 160 160 130 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/μs max 45 75 20 500 100 200 30 500 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A 20 150 150 90 50 75 75 C 50 500 400 200 150 200 175 1 1 1 1 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Parameter Value Unit DO-214AA TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W V-I Characteristics tr x td Pulse Waveform VS VDRM VF IPP – Peak Pulse Current – %IPP +I VT -V IDRM +V IH IS IT tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 90 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Numbering Part Marking Cathode Indicator P xxx 1 S X L RP DEVICE TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE REEL PACK XXXXX XXXXX L: RoHS COMPLIANT IPP RATING PACKAGE TYPE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 91 Revised: February 22, 2011 Part number code (refer to Electrical Characteristics table) Date code SIDACtor ® Protection Thyristors SLIC Protection Dimensions — DO-214AA Case Temperature Measurement Point Cathode Indicator B D Dimensions C A H E F K G 0.079 (2.0) Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 Dimensions are in inches (and millimeters). 0.110 (2.8) 0.079 (2.0) Inches Pad Outline (MM) Packing Options Package Type S Description Quantity Added Suffix Industry Standard DO-214AA Tape & Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) Cathode 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Cover tape Dimensions are in inches (and millimeters). Direction of Feed 92 Revised: February 22, 2011