CLOCK OSCILLATORS – High Frequency “H572 Series” Logic: HCMOS 5x7 mm Wave Form: Square wave MERCURY Since 1973 H572, an extended product of SWO series, offers economic solution for high frequency (96 ~200 MHz) clock oscillator with low phase noise (-135 dBc/Hz at 10 KHz) and high performance. Output options include standard drive (10 mA) or high drive (30 mA). General Specifications TA=+25°C, VDD at specified voltage, CL=15 pF Product Series H572 Standard Drive High Drive (output option code is “S’) (output option code is “H’) 12 MHz ~200 MHz HCMOS +3.3 V ±10% (voltage code is “3”) PRELIMINARY Output Options Frequency Range Output Logic Input Voltage Range (VDD) +2.4 V D.C. min. +0.4 V D.C. min. Output Voltage HIGH “1”; VOH Output Voltage LOW “0”; VOL Output Drive Current Rise Time / Fall Time 10 mA min. 30 mA min. 3 n sec. 0.3 V ↔ 3.0 V. 15pF load. 2 n sec. 0.3 V ↔ 3.0 V. 15pF load 45% min; 55% max. measured at 50% VDD 10 m sec. typical; VDD reaches 1.62 V 15 pF Stability code “A”:±25 ppm over 0°C to +70°C Stability code “B”:±50 ppm over 0°C to +70°C Stability code “C”: ±100 ppm over 0°C to +70°C”) If non-standard please enter the desired stability after the “C”. For example “C20” represents ±20 ppm over 0 to +70°C Stability code “D”:±25 ppm over -40°C to +85°C Stability code “E”:±50 ppm over -40°C to +85°C Stability code “F”:±100 ppm over -40°C to +85°C If non-standard please enter the desired stability after the “I”. For example “I20” represents ±20 ppm over -40 to +85°C Duty Cycle (Symmetry) Start-up Time (Ts) Load Commercial (0°C to +70°C) Temperature code Frequency is ‘C” Stability(1) Industrial (-40°C to +85°C) Temperature code is ‘I” Period Jitter RMS Phase Noise (+3.3V 44.736 MHz) (+3.3V 155.520 MHz) Pad 1 Options Aging ESD Protection Packaging Offset dBc / Hz dBc / Hz 77.760 MHz: 3 ps typical. With capacitive decoupling between VDD and ground 125.0 MHz: 3.5 ps typical. With capacitive decoupling between VDD and ground 155.520 MHz: 4 ps typical. With capacitive decoupling between VDD and ground 100 Hz 1 KHz 10 KHz 100 KHz 1 MHz -80 -110 -135 -130 -132 -80 -110 -125 -120 -125 When connected to ground: Output is disabled When no connection or connected to logic high: Frequency output. Disable time is 10 m sec. typical. Enable time (when ground is removed from pad 1) is 10 m sec. typical. ±5 ppm per year max. 2000 V max; Human body model 16 mm tape; 8 mm pitch; 1000 pcs per reel MERCURY www.mercury-crystal.com Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected] U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected] MERCURY Page 1 of 3 Date: Feb. 5, 2005 Rev. 0 CLOCK OSCILLATORS – High Frequency “H572 Series” Logic: HCMOS 5x7 mm Wave Form: Square wave MERCURY Since 1973 (1) Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging, shock and vibration. Environmental Performance Specifications RoHS Compliance Storage temp. range Humidity Hermetic seal Solderability Reflow Vibration Shock Pb (lead) free -55 to +125°C 85% RH, 85°C, 48 hours Leak rate 2x10-8 ATM-cm3/sec max. MIL-STD-202F method 208E 260°C for 10 sec. MIL-STD-202F method 204, 35G, 50 to 2000 Hz MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave Part Number Format and Example: Example: 3H572S-AT-125.000 Explanation: H572 clock oscillator with standard drive output, +3.3 V supply voltage, ±25 ppm frequency stability over 0 to +70°C, pad 1 tri-state function,125.000 MHz " 3H572 " — S A " T " — 125.000 n o p q r n: Voltage codes: “3” for +3.3 V ; o Output option: “S” for standard drive; “H” for high drive p: Frequency stability code: “A” ~ “F” or custom. See table above. q: “T”: Tri-state option on pad 1 (Tri-state is standard if not specified), leave blank if tri-state is not required. r Frequency in MHz H572 Test Circuit: H572 OUTPUT WAVEFORM: Tr VOH VOL Tf 90% Vcc 10% Vcc TH T Duty Cycle = (TH / T) 100% MERCURY Page 2 of 3 Date: Feb. 6, 2002 Rev. 1 CLOCK OSCILLATORS – High Frequency “H572 Series” Logic: HCMOS 5x7 mm Wave Form: Square wave H572 Package Dimensions and Recommended Pad Layout: [0.024] 0.6 3 2 0.55 [0.022] 1.4±0.2 [0.055±0.008] 1 Pad 1 Pad 2 Pad 3 Pad 4 Tri-State or No Connection Ground Output Supply voltage 3 2 0. 5 x4 [0.055] 1.4 5° 4 1 5.08 [0.200] typical bottom view 2.2[0.086] 1.8[0.071] MEC [0.004] 0.1 [0.049] 1.25 _ H572_ Since 1973 unit mm[inches] 2.0[0.079] [0.197±0.006] 5.00±0.15 4 [0.275±0.006] 7.00±0.15 MERCURY 5.08 [0.200] Chamfered pad is pad No. 1. Count counter-clockwise when looking at top view. Count clockwise when looking at bottom view. RECOMMENDED REFLOW SOLDERING PROFILE MERCURY Page 4 of 4 Date: Feb. 5, 2005 Rev. 0