GPF576

Voltage Controlled Crystal Oscillators
3GPF576 Series +3.3V, “F” family,
VCXO
PECL Outputs
MERCURY
Since 1973
3GPF576 VCXO products feature 0.4 ps typical phase jitter and
low phase noise (-132 dBc at 10 KHz for 155.520 MHz).
Differential PECL Outputs meet the requirements for
SONET, XDSL and other communication protocols.
General Specifications
Product Series
Frequency Range
Output Logic
3GPF576
38 MHz ~ 640 MHz.
Differential PECL 100 K square wave
Industrial “ I ”:
Commercial “ C ”::
Stability Code
-10°C to +70°C
-40°C to +85°C
±25 ppm
A
D
±50 ppm
B
E
±100 ppm
C
F
Ixx
Custom ±xx ppm
Cxx
If custom, use “temperature range code + desired ppm stability” for the
stability code. Example: “C20” (±20 ppm over -10 to +70°C) or “I35”.
Frequency Stability
vs Operating Temperature
Range
vs Supply Voltage Change
vs Load Change
±3 ppm max.with ±10% supply voltage change
±2 ppm max.with ±10% Load change:
Supply Voltage VCC
+3.3 V ± 10 %
Output Voltage HIGH “1”, VOH
2.275 V min.; 2.420 V max. Condition: 50 ohms to VDD-2V
Output Voltage LOW “0”, VOL
1.490 V min..; 1.680 V max. Condition: 50 ohms to VDD-2V
38 MHz≤ fout ≤ 100 MHz: 70 mA max.
100 MHz< fout ≤ 320 MHz: 85 mA max
320 MHz< fout ≤ 640 MHz: 95 mA max
50 ohms into VCC-2V or Thevenin equivalent (terminating resistors
required on all outputs). See test circuit below.
fout < 150 MHz: 0.5 ns typical; 0.7 ns max.
150 MHz ≤ fout ≤ 320 MHz: 0.4 ns. typical; 0.55 ns. max
320 MHz < fout ≤ 640 MHz: 0.3 ns. typical; 0.45 ns. max
Measured at 20% ↔ 80% of the wave form.
50% ± 5% max. measured at 50% waveform.
Current Consumption
Load
Rise Time (Tr) and
Fall Time (Tf)
Voltage Control
Characteristics
(pad No. 1)
Duty Cycle
Tri-state
Control Voltage Center
+1.65 V
Control Voltage Range
Linearity
Vcon= +0.3 V to +3.0 V
From ± 80 ppm to ± 120 ppm. Use “N” (minimum), “M”
(maximum), “T” (typical, ±20%) for the desired range.
Example: 120M represents ±120 ppm maximum.
6% typical; 10% max.
Slope Polarity (Transfer Function)
Positive: Positive voltage for positive frequency shift
Modulation Band Width
25 KHz min. (- 3dB, 0V ≤ Vcon ≤ 3.3V)
Input Impedance
60 KΩ min.
Frequency Deviation Range
No Connection
Differential PECL and complimentary PECL outputs.
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected]
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected]
MERCURY
Page 1 of 4
Date: April 1, 2008
Rev. 1
Voltage Controlled Crystal Oscillators
3GPF576 Series +3.3V, “F” family,
VCXO
PECL Outputs
MERCURY
Since 1973
Start-up Time
Both outputs are disabled (high impedance) when pad No. 2 is taken
below 0.45*Vcc referenced to ground (threshold). Oscillator is always
ON. Only buffer stage is disabled.
Disable current: 50 uA max. (at 0.0 V).
Disable time: 10 ns max.
At disabled mode, both outputs are enabled when pad No. 2 is taken
above 0.45*Vcc referenced to ground (threshold).
Enable time: 10ns+one period of the output frequency max.
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
-65
-96
-124
-136
-132
-145
-149
-62
-92
-120
-132
-128
-144
-150
-59
-86
-116
-129
-124
-140
-148
-48
-80
-108
-118
-114
-131
-138
Period Jitter
Period Jitter
Integrated Jitter RMS
(RMS)
(peak-to-peak)
(12 KHz ~20 MHz)
2.5 ps typ; 4.0 ps max
18 ps typ.; 30 ps max
0.4 ps typ; 0.5 ps max.
3.0 ps typ; 5.0 ps max
20 ps typ.; 30 ps max
0.4 ps typ; 0.5 ps max.
3.0 ps typ; 5.0 ps max
25 ps typ.; 30 ps max
0.4 ps typ; 0.5 ps max.
6.0 ps typ; 8.0 ps max
40 ps typ.; 50 ps max
0.4 ps typ; 0.5 ps max.
5 m sec. max.
Aging
±3 ppm / year max.
Packaging
179 mm reel; 16 mm tape, 8.0 mm pitch. 1000 pcs per reel.
Contact Pad Surface Finish
Nickel over gold on ceramic substrate
Function
on pad
No. 2
Disable
Enable
SSB Phase
Noise
(dBc/Hz)
Jitter
Offset
77.760 MHz
155.520 MHz
311.020 MHz
622.080 MHz
77.760 MHz
155.520 MHz
311.020 MHz
622.080 MHz
(1)
Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging at +25°C, shock and
vibration.
Absolute Maximum Rating Permanent damage may be created if operate beyond limits specified
Supply Voltage VDD
Input Voltage Vi
Input Voltage Vo
E S D Protection
+4.6 V D.C. max.
Vss-0.5V min.; VDD +0.5V max.
Vss-0.5V min.; VDD +0.5V max.
2 KV max. Human body model
Environmental Performance Specifications
Green Requirement
Moisture Sensitivity Level
Storage temp. range
Humidity
Hermetic seal
Solderability
Vibration
Shock
MERCURY
RoHS Compliant and Pb (lead) free
Level 1
-55 to +125°C
85% RH, 85°C, 48 hours
Leak rate 2x10-8 ATM-cm3/sec max.
MIL-STD-202F method 208E
MIL-STD-202F method 204, 35G, 50 to 2000 Hz
MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave
Page 2 of 4
Date: April 1, 2008
Rev. 1
Voltage Controlled Crystal Oscillators
3GPF576 Series +3.3V, “F” family,
VCXO
PECL Outputs
MERCURY
Since 1973
Part Number Format and Example:
Example: 3GPF576A-120N-155.520
Explanation: +3.3V GPF576 series PECL output clock oscillator, 155.520 MHz, frequency stability is ±25 ppm over
0°C to +70°C, frequency deviation range is ±100 ppm minimum.
": customer to specify
"
"
"
"
3
GPF576
A
—
120
N
—
155.520
n
o
p
q
r
s
n: Voltage codes: “3” for +3.3 V; o: GPF576 product series. ‘G” for VCXO; “P” for PECL; “F”: for “F” family
performance.“576” for 5x7 mm SMD with 6 pads. p: Frequency stability code: “A” ~ “F” or custom. See table
above. q: Frequency deviation range in ppm r Frequency deviation range code. “N” for minimum; “M” for
maximum; “T” for typical (±20%) s Frequency in MHz
3GPF576 Test Circuit and Wveform:
+3.3 V
+3.3 V
6
A
1.30 V
50 ohms
0.1uF
Control
Voltage
+
-
2
3
82.5
ohms
-
1
PECL
Duty Cycle
Duty Cycle
45% ~ 55%
45% ~ 55%
80%
50%
20%
MEC
+
V
4
3GPF576
+
-
5
127
ohms
Supply
Voltage
82.5
ohms
PECL
127
ohms
PECL
1.30 V
50 ohms
PECL
Tr
Top view
Tf
Duty
80
50
20
MERCURY
Page 3 of 4
Date: April 1, 2008
Rev. 1
Voltage Controlled Crystal Oscillators
3GPF576 Series +3.3V, “F” family,
VCXO
PECL Outputs
3GPF576 Package Dimensions and Recommended Pad Layout:
6
3GPF576
MEC
4
5
6
3
2
1
3
2
1
[0.055]
0.6[0.024]
4
5
Since 1973
unit mm[inches]
2.54[0.100]
[0.275±0.006]
MERCURY
typical
bottom view
Pad 1 Voltage Control Pad 4 PECL Output
Pad 2 Tri-State
Pad 5 Comp. PECL
Pad 3 Ground
Pad 6 Supply Voltage
Chamfered pad is pad No. 1. Count counter-clockwise when looking at top view.
Count clockwise when looking at bottom view.
3GPF576 Recommended Solder Reflow Profile
Topside temperature of board to be 260°C min. and 270°C max.
Temperature ( °C)
260
250
240
Peak Temperature: 260°C max. and 10 sec. max.
Time within 5°C of actual peak: 20 to 40 sec. max.
Liquidus Temperature
200
150
Flux Activation
Temperature
100
50
Pre-heat 1
30
MERCURY
60
90
t
Ram
up a x.
p
p
m
a
a
6
°C / down
R
cm
e
s
sec
20~40 sec.
a
/
ma t
3°C
x.
Soaking temp: 140°C~225°C
Soaking time: 60~120 sec.
Reflow
Zone
Soaking Zone
30~60 sec.
Pre-heat 2
Cooling
120 150 180
Page 4 of 4
210 240 270 300 330
Date: April 1, 2008
Time
(sec)
Rev. 1