HDF5761

Differential LVDS Crystal Clock Oscillators
3HDF5761 Series +3.3V, “F” Family
LVDS Outputs
MERCURY
Since 1973
3HDF5761 products feature 0.4 ps typical phase jitter and
low phase noise (-132 dBc at 10 KHz for 155.520 MHz).
Differential LVDS Outputs meet the requirements for
SONET, XDSL and other communication protocols.
General Specifications
Product Series
Frequency Range
Output Logic
3HDF5761 ; “F” family. Tri-State on pad 1
38 MHz ~ 640 MHz.
Differential LVDS 100 K square wave
Commercial “ C ”::
Industrial “ I ”:
Stability Code
-10°C to +70°C
-40°C to +85°C
±25 ppm
A
D
±50 ppm
B
E
±100 ppm
C
F
Custom ±xx ppm
Cxx
Ixx
If custom, use “temperature range code + desired ppm stability” for the stability
code. Example: “C20” (±20 ppm over -10 to +70°C) or “I35”.
38.880 MHz ≤ fout <100 MHz: 45 mA max;
100 MHz ≤ fout <320 MHz: 60 mA max.
320 MHz≤ fout ≤ 432 MHz: 70 mA max; (Measured with load).
Frequency Stability
vs Operating Temperature
range
Current Consumption
vs Supply Voltage Change
±3 ppm max.with ±10% supply voltage change
vs Load Change
±2 ppm max.with ±10% Load change:
Supply Voltage VCC
+3.3 V ± 10 % (Voltage code is “33”)
Supply Voltage magnitude Change (∆ VDD)
Output Voltage
Levels
-50 m V min.; +50 m V max.
Logic High
VOH: 1.4 V typical; 1.6 V max. Condition: 100 Ω differential load.
Logic Low
VOL: 0.9 V min.; 1.1 V typical. Condition: 100 Ω differential load.
Offset Voltage (VOS)
1.125 V min.; 1.20 V typical; 1.375 V max.
Offset Magnitude Change ( ∆VOS)
0.0 mV min.; 3 mV typical; 25 mV max.
Output Differential Voltage (VOD)
247 mV min.; 355 mV typical; 454 mV max.
Rise Time and Fall Time (Tr ; Tf)
0.7 ns typical; 1 ns max. 20%  80% of waveform; 100 ohm differential load.
Duty Cycle
50% ± 5% max. measured at 50% waveform
No Connection
Tri-state
Function
on pad
No. 1
Differential LVDS and complimentary LVDS outputs.
Disable
Enable
SSB Phase
Noise (dBc/Hz)
Offset
77.760 MHz
155.520 MHz
Both outputs are disabled (high impedance) when pad No. 2 is taken
below 0.45*Vcc referenced to ground (threshold). Oscillator is always
ON. Only buffer stage is disabled.
Disable current: 50 uA max. (at 0.0 V).
Disable time: 10 ns max.
At disabled mode, both outputs are enabled when pad No. 2 is taken
above 0.45*Vcc referenced to ground (threshold).
Enable time: 10ns+one period of the output frequency max.
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
-65
-96
-124
-136
-132
-145
-149
-62
-92
-120
-132
-128
-144
-150
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected]
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected]
MERCURY
Page 1 of 4
Date: Aug. 24, 2009
Rev. 2
Differential LVDS Crystal Clock Oscillators
3HDF5761 and 3HDF5762 Series +3.3V, “F” family
311.020 MHz
622.080 MHz
Start-up Time
Aging
±3 ppm / year max.
Packaging
179 mm reel; 16 mm tape, 8.0 mm pitch. 1000 pcs per reel.
Contact Pad Surface Finish
Nickel over gold on ceramic substrate
77.760 MHz
155.520 MHz
311.020 MHz
622.080 MHz
-129
-124
-118
-114
Period Jitter
(peak-to-peak)
18 ps typ.; 30 ps max
20 ps typ.; 30 ps max
25 ps typ.; 30 ps max
40 ps typ.; 50 ps max
Since 1973
-86
-116
-80
-108
Period Jitter
(RMS)
2.5 ps typ; 4.0 ps max
3.0 ps typ; 5.0 ps max
3.0 ps typ; 5.0 ps max
6.0 ps typ; 8.0 ps max
5 m sec. max.
Jitter
-59
-48
MERCURY
-140
-148
-131
-138
Integrated Jitter RMS
(12 KHz ~20 MHz)
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
0.4 ps typ; 0.5 ps max.
(1)
Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging at +25°C, shock and
vibration.
Absolute Maximum Rating
Permanent damage may be created if operate beyond limits specified
Supply Voltage VDD
Input Voltage Vi
Input Voltage Vo
E S D Protection
+4.6 V D.C. max.
Vss-0.5V min.; VDD +0.5V max.
Vss-0.5V min.; VDD +0.5V max.
2 KV max. Human body model
Environmental Performance Specifications
Green Requirement
Moisture Sensitivity Level
Storage temp. range
Humidity
Hermetic seal
Solderability
Vibration
Shock
RoHS Compliant and Pb (lead) free
Level 1
-55 to +125°C
85% RH, 85°C, 48 hours
Leak rate 2x10-8 ATM-cm3/sec max.
MIL-STD-202F method 208E
MIL-STD-202F method 204, 35G, 50 to 2000 Hz
MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave
Part Number Format and Example:
Example: 3HDF5761-A-155.520
Explanation: +3.3V HDF5761 series (with Tri-state on pad 1) LVDS output clock oscillator, 155.520 MHz, frequency
stability is ±25 ppm over -10°C to +70°C.
: customer to specify


3
HDF5761
—
A
—
155.520




: Voltage codes: “3” for +3.3 V; : HDF5761 product series. „H” for clock; “D” for LVDS; “F”: for “F” family
performance.“576” for 5x7 mm SMD with 6 pads; “1” for Tri-state on pad No. 1 : Frequency stability code: “A” ~
“F” or custom. See table above. : Frequency in MHz
MERCURY
Page 1 of 4
Date: Aug. 24, 2009
Rev. 2
Differential LVDS Crystal Clock Oscillators
3HDF5761 and 3HDF5762 Series +3.3V, “F” family
MERCURY
Since 1973
3HDF5761Test Circuit and Waveform:
LVDS
A
+
5
3HDF5761
+
0.1uF
1
2
VOS
0.0V
Differential
LVDS
Duty Cycle
50
ohms
MEC
V
-
4
3
V Differential
6
50 ohms
VOD
Supply
Voltage
-
LVDS
LVDS
80%
50%
20%
Tr
Tf
Duty Cycle
80%
50%
20%
MERCURY
Page 1 of 4
Date: Aug. 24, 2009
Rev. 2
Differential LVDS Crystal Clock Oscillators
3HDF5761 and 3HDF5762 Series +3.3V, “F” family
3HDF5761 Package Dimensions and Recommended Pad Layout:
Pad 1 Tri-state
Pad 4 LVDS Output
Pad 2 No Connection Pad 5 LVDS Output
Pad 3 Ground
Pad 6 Supply Voltage
[0.004]
0.1
0.7 [0.028]
3
[0.055]
1.4
4
5
6
3
2
1
.7
2.54[0.100]
5.08 [0.200]
typical
bottom view
1.5[0.059]
2.0[0.079]
2
1
1.8 max.
[0.071 max.]
MEC
unit: mm [inches]
Top view
Rounded pad is pad No. 1
1.8[0.071]
3HDF5761
Since 1973
R0
0.6[0.024]
[0.050]
1.27
[0.197± 0.006]
5.00± 0.15
[0.275± 0.006]
7.00± 0.15
6
5
4
MERCURY
5.08 [0.200]
3HDF5761 Recommended Solder Reflow Profile
Topside temperature of board to be 260°C min. and 270°C max.
Temperature ( °C)
260
250
240
Peak Temperature: 260°C max. and 10 sec. max.
Time within 5°C of actual peak: 20 to 40 sec. max.
Liquidus Temperature
200
150
Flux Activation
Temperature
100
50
Pre-heat 1
30
MERCURY
60
90
t
Ram
up a x.
p
m
a
6°C p dow
Ra ec m
/sec n at
s
20~40
sec.
/
ma
3°C
x.
Soaking temp: 140°C~225°C
Soaking time: 60~120 sec.
Reflow
Zone
Soaking Zone
30~60 sec.
Pre-heat 2
Cooling
120 150 180
Page 4 of 4
210 240 270 300 330
Date: Aug. 24, 2009
Time
(sec)
Rev. 2