ME05SI Series High Isolation, 0.5W Ultra-Miniature SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 0.5W Output Power Input Parameter Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input • Ultra-Miniature SIP Case • 35 Standard Models Input Voltage Range • 3,000 VDC Isolation • >1.1 MHour MTBF Input Reflected Ripple Current Input Filter • -40°C to +85°C Operation Output Parameter Output Voltage Accuracy Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit Min. 2.97 4.50 10.80 21.60 43.20 Typ. 3.3 5.0 12.0 24.0 48.0 20 Max. 3.63 5.50 13.20 26.40 52.80 Units VDC mA P - P Internal Capacitor Conditions Min. Typ. ±3.0 For VIN Change of 1% ±1.2 See Model Selection Guide 100 ±0.02 Momentary (0.5 Sec.) Max. Units % % mV P - P %/°C General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI Characteristics, See Note 3 Parameter Radiated Emissions Conducted Emissions ESD RS EFT Surge CS PFMF Conditions 60 Seconds 500 VDC 100 kHz, 1V Conditions EN 55022 EN 55022 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 Min. 3,000 1,000 Typ. Max. 60 80 Min. Typ. Min. -40 Typ. +25 Units VDC M pF kHz Max. Units Class B Class B Criteria A; ±8 kV Air/±6 kV Contact Criteria A; 10V/m Criteria A; ±2 kV Criteria A; ±0.5 kV Criteria A; 10 Vrms Criteria A; 1A/m Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Physical 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Ambient Case -40 Free Air Convection RH, Non-condensing 48 VIN Models All Other Models Case Size MicroPower Direct Conditions Case Material Weight Max. +85 +100 +125 Units °C °C °C 95 % 0.46 x 0.29 x 0.40 Inches (11.68 x 7.5 x 10.2 mm) 0.46 x 0.24 x 0.40 Inches (11.68 x 6.0 x 10.2 mm) Non-Conductive Black Plastic (UL-94V0) 0.05 Oz (1.5g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 1.121 Typ. Max. Units MHours Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec Min. -0.0 -0.0 -0.0 -0.0 -0.0 Typ. Max. 6.0 7.0 15.0 28.0 54.0 260 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Model Number ME0503S-03I ME0503S-05I ME0503S-09I ME0503S-12I ME0503S-15I ME0503S-18I ME0503S-24I ME0505S-03I ME0505S-05I ME0505S-09I ME0505S-12I ME0505S-15I ME0505S-18I ME0505S-24I ME0512S-03I ME0512S-05I ME0512S-09I ME0512S-12I ME0512S-15I ME0512S-18I ME0512S-24I ME0524S-03I ME0524S-05I ME0524S-09I ME0524S-12I ME0524S-15I ME0524S-18I ME0524S-24I ME0548S-03I ME0548S-05I ME0548S-09I ME0548S-12I ME0548S-15I ME0548S-18I ME0548S-24I Input Voltage (VDC) Nominal Range 3.3 2.97 - 3.63 3.3 2.97 - 3.63 3.3 2.97 - 3.63 3.3 2.97 - 3.63 3.3 2.97 - 3.63 3.3 2.97 - 3.63 3.3 2.97 - 3.63 5.0 4.5 - 5.5 5.0 4.5 - 5.5 5.0 4.5 - 5.5 5.0 4.5 - 5.5 5.0 4.5 - 5.5 5.0 4.5 - 5.5 5.0 4.5 - 5.5 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 24 21.6 - 26.4 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 48 43.2 - 52.8 Current (mA) Full-Load No-Load 205 20 216 25 216 25 201 25 208 25 208 25 208 25 132 20 121 13 128 15 127 18 130 22 127 20 134 25 58 15 54 10 57 15 58 20 61 20 61 15 59 15 31 8 29 8 30 10 30 8 29 10 29 10 29 10 17 6 16 6 17 6 17 6 17 6 17 6 18 10 Output Voltage Current (VDC) (mA, Max) 3.3 5.0 9.0 12.0 15.0 18.0 24.0 3.3 5.0 9.0 12.0 15.0 18.0 24.0 3.3 5.0 9.0 12.0 15.0 18.0 24.0 3.3 5.0 9.0 12.0 15.0 18.0 24.0 3.3 5.0 9.0 12.0 15.0 18.0 24.0 Fuse Capacitive Load ciency Rating Regulation Effi Load (%, Typ) Slow-Blow (% Typ) 152.0 100.0 56.0 42.0 33.0 28.0 21.0 152.0 100.0 56.0 42.0 33.0 28.0 21.0 152.0 100.0 56.0 42.0 33.0 28.0 21.0 152.0 100.0 56.0 42.0 33.0 28.0 21.0 152.0 100.0 56.0 42.0 33.0 28.0 21.0 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. Operation at no-load will not damage these units. However, they may not meet all specifications. 3. These converters will operate without external components. However, to meet the specified EMI limits, a simple external input filter is required. See the input filter note below for more information. 4. All units are rated for operation at full output power to +85°C. Operation over +85°C without airflow is not recommended. Output power should be derated linearly from 100% at 85°C to 0% at 100°C. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. ±20 ±10 ±10 ±10 ±10 ±10 ±10 ±20 ±10 ±10 ±10 ±10 ±10 ±10 ±20 ±10 ±10 ±10 ±10 ±10 ±10 ±20 ±10 ±10 ±10 ±10 ±10 ±10 ±20 ±10 ±10 ±10 ±10 ±10 ±10 (µF, Max) (mA) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 500 500 500 500 500 500 500 250 250 250 250 250 250 250 150 150 150 150 150 150 150 75 75 75 75 75 75 75 50 50 50 50 50 50 50 76 70 70 72 73 73 73 76 83 78 79 77 79 75 72 78 73 72 69 68 71 69 73 71 71 73 73 72 60 66 62 64 62 62 61 Mechanical Dimensions Input Filter Pin Connection Connections The filter (C1, C2, C3 & L1) shown in the figure above is required to meet EN 55022 level B. Recommended component values are shown in the table at right. Capacitor C1 is a 1210, 100V/ceramic, except for the 48V input which is a 100V/electrolytic. Capacitor C2 is a 1210 100V/ceramic. Capacitor C3 is a 1206 3 kV/ceramic. Capacitor C 4 is added to meet EN 61000-4-4 and EN 61000-4-5. This capacitor is a 470 µF, 100V/electrolytic. All components should be mounted as close to the unit as possible. VIN C1 L1 C2 C3 (VDC) (µF) (µH) (µF) (pF) 3.3 5.0 12 24 48 2.2 2.2 2.2 2.2 10.0 18.0 18.0 18.0 18.0 18.0 2.2 2.2 470 470 Pin 1 2 3 4 For 48VDC input models the width of tthe unit is 0.29 (7.5) and the pins are set 0. 0.08 (2.0) from the edge of the case. The These dimensions are identifi identified ed with an “*” on the mechanical drawing MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • Description -VIN +VIN -VOUT +VOUT TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the front of the unit FAX: (781) 344-8481 • E-Mail: [email protected]