E200E Series Low Cost, 2W Ultra-Miniature SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: • 2W Output Power Parameter Input Voltage Range • Ultra-Miniature SIP Case • Low 0.3” Profile Reverse Polarity Input Current • 1,000 VDC Isolation Input Filter • >3.5 MHour MTBF • 5V & 12V Inputs • LOWEST COST! Conditions Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 VDC 0.3 A Max. Units Internal Capacitor Output Parameter Conditions Min. Typ. Output Voltage Accuracy Line Regulation Load Regulation (Note 1) ±1.0 ±3.0 % ±1.2 % 50 75 mV P - P ±0.01 ±0.03 %/°C Max. Units For Vin Change of 1% See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) Output Power Protection 120 Temperature Coefficient Output Short Circuit RoHS Compliant Units % Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Isolation Test Voltage Min. 60 Seconds Typ. 1,000 VDC Flash Tested For 1 Sec 1,100 VDC 1,000 VDC 1,000 Isolation Resistance Isolation Capacitance 100 kHz, 1V MΩ 60 Switching Frequency 100 pF 75 kHz Environmental Parameter Conditions Operating Temperature Range Ambient Operating Temperature Range Case Storage Temperature Range 292 Page Street Suite D Stoughton, MA 02072 USA Humidity Typ. Max. Units -40 +25 +85 °C -55 Cooling MicroPower Direct Min. +90 °C +125 °C 95 % Free Air Convection RH, Non-condensing Physical Case Size 0.46 x 0.40 x 0.30 Inches (11.6 x 10.2 x 7.55 mm) Case Material Non-Conductive Black Plastic (UL-94V0) Weight T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com 0.06 Oz (1.8g) Reliability Specifications Parameter MTBF Conditions Min. MIL HDBK 217F, 25°C, Gnd Benign 3.5 Conditions Min. Typ. Max. Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 Units VDC 1.5 mm From Case For 10 Sec 260 °C All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Input Output Load Voltage (VDC) Current (mA) Voltage Current Current Regulation Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (% Max) 5 4.5 - 5.5 513 38 5.0 400.0 40.0 15 78 Fuse Rating Slow-Blow (mA) 1,000 E202E 5 4.5 - 5.5 506 38 12.0 167.0 17.0 15 79 1,000 E203E 5 4.5 - 5.5 506 38 15.0 133.0 14.0 15 79 1,000 E211E 12 10.8 - 13.2 214 20 5.0 400.0 40.0 15 78 500 E212E 12 10.8 - 13.2 208 20 12.0 167.0 17.0 15 80 500 E213E 12 10.8 - 13.2 206 20 15.0 133.0 14.0 15 81 500 Model Number E201E Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 4. These converters are specified for operation without external components. However, in some applications the addition of input/ouput capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Vin 5 VDC 12 VDC Input Capacitor 4.7 µF 2.2 µF Vout 5 VDC 12 VDC 15 VDC Efficiency (%, Typ) Derating Curve Output Capacitor 10.0 µF 2.2 µF 1.0 µF For applications requiring very low output noise levels, a simple LC filter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Description 1 -Vin 2 +Vin 3 -Vout 4 +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]