SKE10 10W DC-DC Regulated Single Output Converter E¡¡E¡½ ¡E¡E ¡E¡E ¡E¡E ¡E¡E ¡EE¡ SPECIFICATION ORDER NO. OUTPUT DC VOLTAGE 5V 12V 15V 24V CURRENT RANGE 200 ~ 2000mA 84 ~ 840mA 66.6 ~ 666mA 42 ~ 420mA RATED POWER 10W 60mVp-p 60mVp-p 80mVp-p RIPPLE & NOISE (max.) Note.2 50mVp-p LINE REGULATION Note.3 0.3% LOAD REGULATION ¡Ó Note.4 ¡Ó0.5% ¡Ó2.0% SWITCHING FREQUENCY 200KHz min. VOLTAGE RANGE A: 9 ~ 18VDC B: 18 ~ 36VDC C: 36 ~ 72VDC 79% 79% 78% 80% 81% EFFICIENCY (Typ.) DC CURRENT Full load A: 1100mA B: 530mA C: 270mA No load A: 28mA C: 8mA B: 16mA 81% 80% 82% 82% 81% 82% 83% Pi network FILTER PROTECTION Fuse recommended OVER CURRENT 160% ~ 250% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed SHORT CIRCUIT All output equipped with short circuit Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. -25 ~ +71 PROTECTION (Note. 5) Features : 2:1 wide input range 4:1 wide input range(option) 1000VDC I/O isolation 3000VDC I/O isolation(option) Built-in EMI filter Protections: Short circuit / Overload Cooling by free air convection Six-sided shield metal case 100% burn-in test Low cost / High reliability Approvals: FCC / CE 2 years warranty SKE10A- SKE10B- SKE10C- SKE10A- SKE10B- SKE10C- SKE10A- SKE10B- SKE10C- SKE10A- SKE10B- SKE10C12 05 05 05 12 12 15 15 15 24 24 24 VOLTAGE ACCURACY INPUT series ¢J (Refer to output load derating curve) 20% ~ 90% RH non-condensing WORKING HUMIDITY STORAGE TEMP., HUMIDITY -25 ~ +105 , 10 ~ 95% RH ENVIRONMENT 0.03% / (0 ~ 50 ) TEMP. COEFFICIENT 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes VIBRATION ¢J ¢J ¡Ó WITHSTAND VOLTAGE I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH ¢J SAFETY & ISOLATION RESISTANCE EMC OTHERS ¢J EMC EMISSION EMC IMMUNITY MTBF DIMENSION Compliance to EN55022 Class B, FCC part 15 Class B Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A 500Khrs min. MIL-HDBK-217F(25 ) WEIGHT 32g ¢J 50.8*25.4*11.2mm or 2"*1"*0.44" inch (L*W*H) Derating Curve Pin Configuration Mechanical Specification Unit:mm 11.27 1 3 4 2 BOTTOM VIEW 5 £r 1.0 + 0.2/-0.1 10.2 10.2 2.5 15.2 2.5 25.4 10.2 5.1 10.1 20.3 Pin no. Output Single 1 2 3 4 5 + Vi n - Vi n + Vo u t No Pin - Vo u t 100 LOAD (%) 50.8 15.3 80 5.8 -25 0 25 50 60 71 Ta ( NOTE ¢J) 100 ¢J 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 10% to 100% rated load. 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds. File Name:SKE10-SPEC 2012-07-18