SCW08 8W DC-DC Regulated Single Output Converter series Features : 2:1 wide input range 1000VDC I/O isolation Built-in EMI filter Protections: Short circuit / Overload Cooling by free air convection Five-sided shield metal case 100% full load burn-in test Low cost / High reliability 2 years warranty SPECIFICATION ORDER NO. SCW08A-05 SCW08B-05 SCW08C-05 SCW08A-12 SCW08B-12 SCW08C-12 SCW08A-15 DC VOLTAGE 5V 12V 15V CURRENT RANGE 320 ~ 1600mA 134 ~ 670mA 106 ~ 533mA 60mVp-p 60mVp-p SCW08B-15 SCW08C-15 81% 81% RATED POWER OUTPUT 8W RIPPLE & NOISE (max.) Note.2 50mVp-p LINE REGULATION Note.3 0.5% LOAD REGULATION Note.4 VOLTAGE ACCURACY SWITCHING FREQUENCY INPUT 2.0% VOLTAGE RANGE 50KHz min. A: 9 ~ 18VDC EFFICIENCY (Typ.) 75% 78% Full load A: 888mA B: 426mA C: 215mA No load A: 50mA C: 15mA DC CURRENT B: 18 ~ 36VDC C: 36 ~ 72VDC 78% B: 25mA 80% 82% 81% 79% Pi network FILTER Fuse recommended PROTECTION OVERLOAD PROTECTION (Note. 5) 0.5% SHORT CIRCUIT WORKING TEMP. 110 ~ 250% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed All output equipped with short circuit Protection type : Hiccup mode, recovers automatically after fault condition is removed -25 ~ +71 (Refer to output load derating curve) 20% ~ 90% RH non-condensing STORAGE TEMP., HUMIDITY -25 ~ +105 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03% / (0 ~ 50 ) WORKING HUMIDITY ENVIRONMENT VIBRATION WITHSTAND VOLTAGE 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes SAFETY ISOLATION RESISTANCE ISOLATION CAPACITANCE I/P-O/P: 100M Ohms / 500VDC / 25 250pF max. Compliance to EN55022 Class B, FCC part 15 Class B Compliance to EN61000-4-2,3,4,5,6,8 light industry level, criteria A OTHERS EMI CONDUCTION & RADIATION EMS IMMUNITY MTBF DIMENSION 900khrs min. MIL-HDBK-217F(25 ) 31.8*20.3*12.2mm or 1.25"*0.80"*0.48" inch (L*W*H) WEIGHT 15g I/P-O/P:1KVDC / 70% RH Derating Curve Pin Configuration Mechanical Specification Unit:mm(inch) 2 22 3 BOTTOM VIEW 16 9 14 11 15.24(0.60) 2.54( 0.10 ) 5.08( 0.20 ) 0.6+ 0.1/-0(0.024) SIDE VIEW 12.2(0.48) 31.8(1.25) 23 17.8(0.70) 3.81(0.15) Pin No. Output 2&3 9 11 14 16 22 & 23 - Vi n N.C. N.C. + Vo u t - Vo u t + Vi n 100 LOAD (%) 20.3(0.80) 80 -25 0 25 50 60 71 Ta ( NOTE 100 ) 1.All parameters are specified at normal input, rated load, 25 70% RH Ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds. File Name:SCW08-SPEC 2008-05-08