RPS-60 60W Single Output Medical Type series ■ Features : 4"×2" miniature size Universal AC input / Full range Low leakage current <100 μA Protections: Short circuit / Overload / Over voltage Cooling by free air convection Medical safety approved (2 x MOPP between primary to secondary) UL60950-1/IEC60950-1/EN60950-1 ITE safety approved No load power consumption<0.75W Fixed switch frequency at 100KHz Suitable for BF application with appropriate system consideration 3 years warranty .. SPECIFICATION MODEL RPS-60-3.3 RPS-60-5 RPS-60-12 RPS-60-15 RPS-60-24 RPS-60-48 DC VOLTAGE 3.3V 5V 12V 15V 24V 48V RATED CURRENT 10A 10A 5A 4A 2.5A 1.25A CURRENT RANGE 0 ~ 11A 0 ~ 11A 0 ~ 5.5A 0 ~ 4.4A 0 ~ 2.75A 0 ~ 1.375A 33W 50W 60W 60W 60W 60W 55W 66W 66W 66W 66W RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p 120mVp-p 150mVp-p 240mVp-p 300mVp-p VOLTAGE ADJ. RANGE 3.1 ~ 3.6V VOLTAGE TOLERANCE Note.3 ±2.0% 4.75 ~ 5.5V ±2.0% 11.4 ~ 13.2V ±2.0% 13.5 ~ 16.5V ±2.0% 22.8 ~ 27.6V ±1.0% 45.6 ~ 52.8V ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% SETUP, RISE TIME 500ms, 30ms/230VAC HOLD UP TIME (Typ.) 50ms/230VAC VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 74% 84% 85% 86% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.8A/115VAC 28.4 ~ 32.4V 55.2 ~ 64.8V RATED POWER PEAK LOAD(10sec.) OUTPUT INPUT LEAKAGE CURRENT Note.4 36.3W 500ms, 30ms/115VAC at full load 12ms/115VAC at full load 127 ~ 370VDC 79% 83% 1 A/230VAC COLD START 60A/230VAC 30A/115VAC Note.8 Earth leakage current < 150 μA/264VAC , Touch current < 100μ A/264VAC OVER LOAD PROTECTION OVER VOLTAGE WORKING TEMP. 115 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 3.8 ~ 5V 5.75 ~ 6.75V 13.8 ~ 16.2V 17.25 ~ 20.25V Protection type : Shut down o/p voltage, re-power on to recover -20 ~ +70℃ (Refer to "Derating Curve") WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 20 ~ 90% RH non-condensing SAFETY STANDARDS SAFETY & ISOLATION LEVEL WITHSTAND VOLTAGE EMC UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1 approved (Note 5) OTHERS ISOLATION RESISTANCE EMC EMISSION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes Primary-Secondary: 2xMOPP, Primary-Earth:1xMOPP, Secondary-Earth:1xMOPP I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC/ 25℃/ 70% RH Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A MTBF 353.6K hrs min. MIL-HDBK-217F (25℃) 101.6*50.8*29mm (L*W*H) 0.15Kg; 96pcs/15.4Kg/0.89CUFT DIMENSION PACKING NOTE -40 ~ +85℃, 10 ~ 95% RH ±0.03%/℃ (0 ~ 45℃) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. 33% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) 6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. Heat Sink HS1,HS2 can not be shorted. 8. Touch current was measured from primary input to DC output. File Name:RPS-60-SPEC 2015-07-17 RPS-60 60W Single Output Medical Type Mechanical Specification series Unit:mm 101.6 3.175 95.25 50.8 44.45 FS1 3.175 HS2 AC FUSE T2.5/250V 3 2 1 CN1 SVR1 1 2 3 4 FS2 AC FUSE T2.5/250V CN2 HS1 M1 M2 3 max. 29 4-ψ3.3 DC Output Connector (CN2) : JST B4P-VH or equivalent AC Input Connector (CN1) : JST B3P-VH or equivalent Pin No. 1 2 3 Assignment AC/N No Pin AC/L Mating Housing Pin No. 1,2 3,4 Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent Mating Housing Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent : Grounding Required 1.HS1,HS2 cannot be shorted. 2.M1 is safety ground. For better EMC performance, Please secure an electrical connection between M1,M2 and chassis grounding. Block Diagram RECTIFIERS & FILTER EMI FILTER I/P Assignment +V -V fosc : 100KHz RECTIFIERS & FILTER POWER SWITCHING +V -V DETECTION CIRCUIT FG O.L.P. CONTROL O.V.P. Output Derating Output Derating VS Input Voltage 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -20 0 10 20 30 40 50 AMBIENT TEMPERATURE (℃) 60 65 70 (HORIZONTAL) 60 50 40 90 95 100 115 120 140 160 180 200 220 240 264 INPUT VOLTAGE (VAC) 60Hz File Name:RPS-60-SPEC 2015-07-17