NPF-90D 90W Single Output Switching Power Supply F 110 M ■ Features Universal AC input / Full range (up to 305VAC) Built-in active PFC function High efficiency up to 90.5% Protections: Short circuit / Over current / Over voltage / Over temperature M SELV series IP67 ■ Applications Indoor LED lighting LED decorative lighting LED architecture lighting Moving sign Tunnel lighting Cooling by free air convection Fully isolated plastic case Fully encapsulated with IP67 level Class Ⅱ power unit, no FG Built-in 3 in 1 dimming function (0~10Vdc or PWM signal or resistance) Suitable for dry / damp / wet locations No load power consumption<0.5W 5 years warranty ■ Description NPF-90D is one 90W waterproof single-output LED power supply series. In addition to the fundamental LED driving function, NPF-90D is equipped with built-in 3 in 1 dimming function (0~10Vdc, PWM signal or resistance) that simplifies the brightness adjustment for system designers so as to achieve light reduction and energy saving. The entire series adopts the universal input range from 90VAC to 305VAC and incorporates a built-in PFC function. The enclosure design is a 94V-0 flame retardant plastic case. The interior is fully potted with silicone that enhances the heat dissipation and allows the power supply to meet the anti-vibration demand up to 5G; it also thus conforms to IP67 level, enabling NPF-90D to be used in a highly dusty and highly humid harsh environment. Providing a high efficiency up to 90.5% and a low no load power consumption below 0.5W, NPF-90D can meet the energy saving demand for the new generation LED lighting. The class Ⅱ design (without FG pin) and the double insulation weather-resistant cable (SJTW) make it convenient for users to flexibly install on various types of lighting systems. The entire series can operate under the temperature between -40~ +70℃ and comply with the relevant global lighting safety certification. ■ Model Encoding NPF - 90 D - 12 Output voltage Built-in 3 in 1 dimming function Output wattage Series name File Name:NPF-90D-SPEC 2014-08-07 NPF-90D 90W Single Output Switching Power Supply series SPECIFICATION MODEL NPF-90D-12 NPF-90D-15 NPF-90D-20 NPF-90D-24 NPF-90D-30 NPF-90D-36 NPF-90D-42 NPF-90D-48 NPF-90D-54 DC VOLTAGE OUTPUT 42V 20V 24V CONSTANT CURRENT REGION 7.2 ~ 12V 9 ~ 15V 12 ~ 20V 14.4 ~ 24V 18 ~ 30V RATED CURRENT 7.5A 6A 4.5A 3.75A 3A 2.5A 2.15A 1.88A 1.67A RATED POWER 48V 90W 90W 90W 90W 90W 90W 90.3W 90.24W 90.18W 54V 21.6 ~ 36V 25.2 ~ 42V 28.8 ~ 48V 32.4 ~ 54V RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p 200mVp-p 250mVp-p 250mVp-p 350mVp-p VOLTAGE TOLERANCE Note.3 ±4.0% ±4.0% ±4.0% ±3.0% ±3.0% ±2.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% LOAD REGULATION ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME Note.4 500ms, 80ms at 95% load INPUT 30V 36V 15V 12V 115VAC / 230VAC HOLD UP TIME (Typ.) 16ms/230VAC VOLTAGE RANGE 90 ~ 305VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.98/115VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 16ms/115VAC at full load 127 ~ 431VDC TOTAL HARMONIC DISTORTION THD< 20% when output loading≧60% at 115VAC/230VAC input and output loading≧75% at 277VAC input EFFICIENCY (Typ.) 88% AC CURRENT (Typ.) 0.95A / 115VAC INRUSH CURRENT(Typ.) COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC LEAKAGE CURRENT <0.25mA / 277VAC OVER CURRENT SHORT CIRCUIT PROTECTION OVER TEMPERATURE 90% 90% 0.5A / 230VAC 89% 90% 90% 90% 90% 0.4A / 277VAC 95 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 15 ~ 17V OVER VOLTAGE 89% 17.5 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 40V 41 ~ 46V 46 ~ 54V 54 ~ 60V 59 ~ 66V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, re-power on to recover WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 95% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP67 approved ; Design refer to EN60335-1 SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH EMC EMISSION Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≧60% load) ; EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level(surge L- N : 2KV), criteria A MTBF 231.2K hrs min. OTHERS DIMENSION PACKING NOTE I/P-O/P:3.75KVAC MIL-HDBK-217F (25℃) 171*63*37.5mm (L*W*H) 0.77Kg; 18pcs/14.9Kg/0.82CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:NPF-90D-SPEC 2014-08-07 NPF-90D 90W Single Output Switching Power Supply series Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT +V -V DIM+ DIM- O.L.P. O.T.P. O.L.P. DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. Derating Curve Static Characteristics 100 100 90 80 230VAC Input only 70 60 50 LOAD (%) LOAD (%) 80 40 20 -40 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz AMBIENT TEMPERATURE (℃) Power Factor Characteristic PF Constant Current Mode 1 .0 0 0 .9 5 0 .9 0 0 .8 5 0 .8 0 0 .7 5 0 .7 0 0 .6 5 0 .6 0 0 .5 5 0 .5 0 0 .4 5 0 .4 0 0 .3 5 0 .3 0 1 1 5 VA C 2 3 0 VA C 2 7 7 VA C 10% 20% 30% 40% 50% 60% LOAD 70% 80% 90% 100% (90W) File Name:NPF-90D-SPEC 2014-08-07 90W Single Output Switching Power Supply NPF-90D series EFFICIENCY vs LOAD (48V Model) NPF-90D series possess superior working efficiency that up to 90.5% can be reached in field applications. 92% 91% 90% EFFICIENCY (%) 89% 88% 115VAC 87% 230VAC 86% 277VAC 85% 84% 83% 82% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. 100 Vo(%) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 60 (min) Hiccup Protection 50 100 Io(%) Typical LED power supply I-V curve File Name:NPF-90D-SPEC 2014-08-07 NPF-90D 90W Single Output Switching Power Supply series DIMMING OPERATION AC/L(Brown) AC/N(Blue) +V(Red) -V(Black) NPF-90D DIM+(Blue) DIM-(White) ※ Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or 0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. ※ Please DO NOT connect "DIM-" to "-V". ※ Reference resistance value for output current adjustment (Typical) Short 10KΩ 20KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ Single driver Resistance Multiple drivers value (N=driver quantity for synchronized Short 10KΩ/N 20KΩ/N 30KΩ/N 40KΩ/N 50KΩ/N 60KΩ/N 70KΩ/N 80KΩ/N 90KΩ/N 100KΩ/N dimming operation) Percentage of rated current 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% OPEN ----95%~108% ※ 0 ~ 10V dimming function for output current adjustment (Typical) Dimming value 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V OPEN Percentage of rated current 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% ※ 10V PWM signal for output current adjustment (Typical): Frequency range:100Hz ~ 3KHz Duty value 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% OPEN Percentage of rated current 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% File Name:NPF-90D-SPEC 2014-08-07 NPF-90D 90W Single Output Switching Power Supply Mechanical Specification Case No.PWM-90P series Unit:mm 171 5 5 300±20 85.5 63 SJTW 18AWG×2C 31.5 AC/L(Brown) AC/N(Blue) 300±20 SJTW 16AWG×2C UL2464 18AWG×2C 5 2 -ψ 4.5 DIM+(Blue) DIM-(White) ※ T case: Max. Case Temperature. 37.5 5 +V(Red) -V(Black) Recommend Mounting Direction Installation Manual Please refer to : http://www.meanwell.com/webnet/search/InstallationSearch.html File Name:NPF-90D-SPEC 2014-08-07