HBG-60
60W Single Output LED Power Supply
F
■ Features
Universal AC input / Full range (up to 295VAC)
Constant current design
Built-in active PFC function
High efficiency up to 91%
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
Class Ⅱ power unit, no FG
Class 2 power unit
No load power consumption<0.5W
5 years warranty
■ Description
110
series
SELV
■ Applications
LED bay lighting
LED down lighting
LED spot lighting
LED mining lighting
LED stage lighting
HBG-60 series is one 60W single output AC/DC LED switching power supply, featuring the
circular shape, specifically designed for the LED luminaries in circular form factor. HBG-60
series is provided in two types: the enclosed type (with the 94V-0 flame retardant plastic case)
and the PCB type. The structure is built to make this series extremely easy to assemble with
the heat sink of the lighting unit or to integrate into the mechanical design of the fixture.
It is thus well suited to adopt HBG-60 with the lighting units such as circular shape LED bay
lighting, LED down lighting, etc.
HBG-60 series accepts the input from 90VAC through 295VAC and is equipped with a built-in
active PFC function. With the Class II design (without FG pin) and the double insulation cables,
it is convenient for users to flexibly set up this series into various kinds of luminaries. The
working efficiency is up to 91% and it can work at the ambient temperature between -40℃
and 70℃ under air convection. HBG-60 series is certified with global luminary related safety
regulation.
■ Model Encoding
HBG - 60 - 1050 P
Blank: Enclosed type
{ P: PCB type
Output current
Output wattage
Series name
File Name:HBG-60-SPEC 2015-01-29
HBG-60
60W Single Output LED Power Supply
series
SPECIFICATION
MODEL
1050mA
1400mA
2100mA
28 ~ 43V
19 ~ 29V
CURRENT ADJ. RANGE Note.4 680 ~ 1050mA
910 ~ 1400mA
1360mA ~ 2100mA
CURRENT ACCURACY
±5.0%
RATED POWER
57.75W
60.2W
60.9W
RIPPLE & NOISE (max.) Note.2 5Vp-p
4Vp-p
3Vp-p
NO LOAD OUTPUT VOLTAGE (max.) 60V
50V
35V
SETUP TIME
500ms / 230VAC 1200ms / 115VAC at 95% load
VOLTAGE RANGE Note.3 90 ~ 295VAC
INPUT
PROTECTION
HBG-60-2100
CONSTANT CURRENT REGION Note.4 37 ~ 55V
RATED CURRENT
OUTPUT
HBG-60-1400
HBG-60-1050
127 ~ 417VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION THD< 20% when output loading≧65% at 115VAC/230VAC input and output loading≧75% at 277VAC input
EFFICIENCY (Typ.)
90%
91%
90%
AC CURRENT
0.7A/115VAC
INRUSH CURRENT (Typ.)
COLD START 45A(twidth=100μs measured at 50% Ipeak) at 230VAC
LEAKAGE CURRENT
<0.75mA / 240VAC
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed
OVER TEMPERATURE
Shut down o/p voltage, re-power on to recover
WORKING TEMP.
-40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 95% RH non-condensing
0.4A/230VAC
0.3A/277VAC
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 60℃)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1 & EN61347-2-13 independent, EN62384 approved
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
SAFETY &
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC
Compliance to EN55015, EN61000-3-2 Class C (≧65% load) ; EN61000-3-3
EMC EMISSION
EMC IMMUNITY
MTBF
OTHERS DIMENSION
PACKING
NOTE
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level(surge 2KV), criteria A
452Khrs min.
MIL-HDBK-217F (25℃)
Enclosed type: ψ110mm * 60.5mm (D * H)
PCB type:ψ99mm *26mm (D * H)
Enclosed type: 0.5Kg; 20pcs/ 11Kg/ 0.94CUFT
PCB type:0.21Kg; 32pcs/ 7.7Kg/ 0.68CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Derating may be needed under low input voltage. Please check the static characteristics for more details.
4. Please refer to "DRIVING METHODS OF LED MODULE".
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
7. Constant current operation region is about 65%~100% rated output voltage, and the output power must be more than rated output power. This is
the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design.
File Name:HBG-60-SPEC 2015-01-29
HBG-60
60W Single Output LED Power Supply
fosc : 50KHz
Block Diagram
EMI FILTER
&
RECTIFIERS
I/P
series
RECTIFIERS
&
FILTER
POWER
SWITCHING
O.L.P.
+V
-V
PWM & PFC
CONTROL
Derating Curve
Static Characteristics
100
100
90
80
80
70
LOAD (%)
LOAD (%)
65
60
40
20
-40
-30
-25
0
15
30
50
60
70 (HORIZONTAL)
60
50
40
90
AMBIENT TEMPERATURE (℃)
100
125
135
145
155 165
175
180
200
230
295
INPUT VOLTAGE (V) 60Hz
Power Factor Characteristic
Constant Current Mode
1
0.95
0.9
0.85
PF
0.8
277V
0.75
230V
0.7
115V
0.65
0.6
0.55
0.5
50%
60%
70%
80%
90%
100%
(60W)
LOAD
File Name:HBG-60-SPEC 2015-01-29
HBG-60
60W Single Output LED Power Supply
series
EFFICIENCY vs LOAD (1050mA Model)
HBG-60 series possess superior working efficiency that up to 91% can be reached in field applications.
92
91
EFFICIENCY (%)
90
89
277V
88
230V
115V
87
86
85
50%
60%
70%
80%
90%
100%
LOAD
DRIVING METHODS OF LED MODULE
This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs.
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
100
Vo(%)
Constant
Current area
Should there be any compatibility issues, please contact MEAN WELL.
65%
Hiccup
Protection
50
100
Io(%)
Typical LED power supply I-V curve
File Name:HBG-60-SPEC 2015-01-29
HBG-60
60W Single Output LED Power Supply
Mechanical Specification
Case No.HBG-60
series
Unit:mm
Blank type:(HBG-60-_)
57.5
47.5
40
98
4
3
50
AC/N(Blue)
98
SVT 18AWG*2C
15
29.64
+V(Red)
-V(Black)
AC/L(Brown)
7.56
11.2
200
300
30
SJTW 18AWG*2C
ψ7 . 9
27.36
50
30
T case
ψ108
ψ110
4-ψ5.28
ψ8.36
ψ9 9
※ T case: Max. Case Temperature.
26
1.6
P type:(HBG-60-_P)
L1
+
HS1
D4
BD1
300
S
Q1
G
D
LF1
KGA
U4
T1
SCR1
LF100
C125
PCB:HBG-60B
A
K
A
UL1015 18AWG*2C
HBG-60A
C1
-V(Black)
+V(Red)
300
FS1
ZNR1
AC/N(Blue)
UL1015 18AWG*2C
T 2A/250 /300VAC
AC/L(Brown)
CN100
D100
C105
C108
C106
C107
ψ
18
Caution
◎ Please inspect the appearance of the product for completeness if the package is damaged. There should not
be any cracks.
◎ Please do not drop or bump the product.
◎ All screws including the suspension screw should be paired with a spring washer and locked tight.
◎ The entire luminaire, including the power supply should be limited to less than 5Kg.
◎ The luminaire should be cautiously protected throughout packaging and transportation to avoid damage due to shock.
◎ Please thoroughly perform the cautionary notes above to prevent the possibility of the luminaire falling and
injuring personnel.
File Name:HBG-60-SPEC 2015-01-29