AD ADUM1310BRWZ

Triple-Channel Digital Isolator with
Programmable Default Output
ADuM1310
FEATURES
GENERAL DESCRIPTION
Pb-free, 16-lead, wide body SOIC package
Low power operation
5 V operation
1.0 mA per channel max @ 0 Mbps to 2 Mbps
3.5 mA per channel max @ 10 Mbps
3 V operation
0.7 mA per channel max @ 0 Mbps to 2 Mbps
2.1 mA per channel max @ 10 Mbps
3 V/5 V level translation
High temperature operation: 105°C
Up to 10 Mbps data rate (NRZ)
Programmable default output state
Safety and regulatory approvals
UL recognition: 2500 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A
VDE certificate of conformity
DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01
DIN EN 60950 (VDE 0805): 2001-12; EN 60950: 2000
VIORM = 560 V peak
The ADuM13101 is a unidirectional, triple-channel digital
isolator based on Analog Devices, Inc. iCoupler® technology.
Combining high speed CMOS and monolithic coreless transformer technology, this isolation component provides outstanding
performance characteristics superior to alternatives such as
optocoupler devices.
By avoiding the use of LEDs and photodiodes, iCoupler
devices remove the design difficulties commonly associated
with optocouplers. The typical concerns that arise with optocouplers, such as uncertain current transfer ratios, nonlinear
transfer functions, and temperature and lifetime effects, are
eliminated with the simple iCoupler digital interfaces and stable
performance characteristics. The need for external drivers and
other discretes is eliminated with these iCoupler products.
Furthermore, iCoupler devices run at one-tenth to one-sixth
the power consumption of optocouplers at comparable signal
data rates.
The ADuM1310 isolator provides three independent isolation
channels at data rates up to 10 Mbps. It operates with the supply
voltage of either side ranging from 2.7 V to 5.5 V, providing
compatibility with lower voltage systems as well as enabling a
voltage translation functionality across the isolation barrier.
This product also has a default output control pin. This allows
the user to define the logic state the outputs are to adopt in the
absence of the input VDD1 power. Unlike other optocoupler
alternatives, the ADuM1310 has a patented refresh feature that
ensures dc correctness in the absence of input logic transitions
and during power-up/power-down conditions.
APPLICATIONS
General-purpose, unidirectional, multichannel isolation
FUNCTIONAL BLOCK DIAGRAM
VDD1 1
16
VDD2
GND1 2
15
GND2
VIA 3
ENCODE
DECODE
14
VOA
VIB 4
ENCODE
DECODE
13
VOB
VIC 5
ENCODE
DECODE
12
VOC
NC 6
11
NC
DISABLE 7
10
CTRL
GND1 8
9
GND2
NC = NO CONNECT
04904-001
ADuM1310
Figure 1.
1
Protected by U.S. Patents 5,952,849; 6,873,065; and other pending patents.
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADuM1310
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................9
Applications....................................................................................... 1
Regulatory Information................................................................9
General Description ......................................................................... 1
ESD Caution...................................................................................9
Functional Block Diagram .............................................................. 1
Pin Configuration and Function Descriptions........................... 10
Revision History ............................................................................... 2
Typical Performance Characteristics ........................................... 11
Specifications..................................................................................... 3
Application Information................................................................ 12
Electrical Characteristics—5 V Operation................................ 3
PC Board Layout ........................................................................ 12
Electrical Characteristics—3 V Operation................................ 4
Propagation Delay-Related Parameters................................... 12
Electrical Characteristics—Mixed 5 V/3 V or 3 V/5 V
Operation....................................................................................... 5
DC Correctness and Magnetic Field Immunity........................... 12
Package Characteristics ............................................................... 7
Insulation and Safety-Related Specifications............................ 7
DIN EN 60747-5-2 (VDE 0884 Part 2) Insulation
Characteristics .............................................................................. 8
Power Consumption .................................................................. 13
Power-Up/Power-Down Considerations ................................ 14
Outline Dimensions ....................................................................... 15
Ordering Guide .......................................................................... 15
Recommended Operating Conditions ...................................... 8
REVISION HISTORY
10/06—Rev. D to Rev. E
Removed ADuM1410 ........................................................Universal
Updated Format..................................................................Universal
Change to Figure 3 ......................................................................... 10
Changes to Table 10........................................................................ 10
Changes to Application Information ........................................... 12
Updated Outline Dimensions ....................................................... 18
Changes to Ordering Guide .......................................................... 18
3/06—Rev. C to Rev. D
Added Note 1 and Changes to Figure 2......................................... 1
Changes to Absolute Maximum Ratings ..................................... 11
11/05—Rev. SpB to Rev. C
5/05—Rev. SpA to Rev. SpB
Changes to Table 6.............................................................................9
10/04—Data Sheet Changed from Rev. Sp0 to Rev. SpA
Changes to Table 5.............................................................................9
6/04—Revision Sp0: Initial Version
Rev. E | Page 2 of 16
ADuM1310
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V OPERATION
4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V; all minimum/maximum specifications apply over the entire recommended operation range,
unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V; all voltages are relative to their respective ground.
Table 1.
Parameter
DC SPECIFICATIONS
Total Supply Current, Three Channels 1
VDD1 Supply Current, Quiescent
VDD2 Supply Current, Quiescent
VDD1 Supply Current, 10 Mbps Data Rate
VDD2 Supply Current, 10 Mbps Data Rate
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH – tPHL|4
Change vs. Temperature
Propagation Delay Skew 5
Channel-to-Channel Matching 6
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity at Logic High Output 7
Symbol
Min
IDD1 (Q)
IDD2 (Q)
IDD1 (10)
IDD2 (10)
IIA, IIB, IIC,
–10
IID, ICTRL, IDISABLE
VIH
VIL
0.8
VOAH, VOBH,
VDD1, VDD2 − 0.4
VOCH, VODH
VOAL, VOBL,
VOCL, VODL
Typ
Max Unit
Test Conditions
2.4
1.2
6.6
2.1
+0.01
3.2
1.6
9.0
3.0
+10
mA
mA
mA
mA
μA
VIA = VIB = VIC = VID = 0
VIA = VIB = VIC = VID = 0
5 MHz logic signal frequency
5 MHz logic signal frequency
0 ≤ VIA, VIB, VIC, VID,
VDISABLE ≤ VDD1, 0 ≤ VCTRL ≤ VDD2
2.0
V
V
V
IOx = –4 mA, VIx = VIxH
0.4
V
IOx = +4 mA, VIx = VIxL
100
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1/VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
4.8
0.2
PW
tPSK
tPSKCD
tR/tF
|CMH|
25
2.5
35
ns
Mbps
ns
ns
ps/°C
ns
ns
ns
kV/μs
Common-Mode Transient Immunity at Logic Low Output7
|CML|
25
35
kV/μs
Refresh Rate
Input Enable Time 8
Input Disable Time8
Input Dynamic Supply Current per Channel 9
Output Dynamic Supply Current per Channel9
fr
tENABLE
tDISABLE
IDDI (D)
IDDO (D)
tPHL, tPLH
PWD
10
20
30
50
5
5
30
5
1
1.2
2.0
5.0
0.19
0.05
Mbps
μs
VIA, VIB, VIC, VID = 0 or VDD1
μs
VIA, VIB, VIC, VID = 0 or VDD1
mA/Mbps
mA/Mbps
Supply current values are for all four channels combined running at identical data rates. Output supply current values are specified with no output load present. The
supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. See Figure 4
through Figure 6 for information on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See Figure 7 and Figure 8 for
total IDD1 and IDD2 supply currents as a function of the data rate for the ADuM1310 channel configurations.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels within the same component.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Input enable time is the duration from when VDISABLE is set low until the output states are guaranteed to match the input states in the absence of any input data logic
transitions. If an input data logic transition within a given channel does occur within this time interval, the output of that channel reaches the correct state within the
much shorter duration as determined by the propagation delay specifications within this data sheet. Input disable time is the duration from when VDISABLE is set high
until the output states are guaranteed to reach their programmed output levels, as determined by the CTRL logic state (see Table 9).
9
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate. See Figure 4 through Figure 6 for
information on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See the Power Consumption section for guidance
on calculating the per-channel supply current for a given data rate.
Rev. E | Page 3 of 16
ADuM1310
ELECTRICAL CHARACTERISTICS—3 V OPERATION
2.7 V ≤ VDD1 ≤ 3.6 V, 2.7 V ≤ VDD2 ≤ 3.6 V; all minimum/maximum specifications apply over the entire recommended operation range,
unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.0 V; all voltages are relative to their respective ground.
Table 2.
Parameter
DC SPECIFICATIONS
ADuM1310, Total Supply Current, Three Channels 1
VDD1 Supply Current, Quiescent
VDD2 Supply Current, Quiescent
VDD1 Supply Current, 10 Mbps Data Rate
VDD2 Supply Current, 10 Mbps Data Rate
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH – tPHL|4
Change vs. Temperature
Propagation Delay Skew (Equal Temperature) 5
Channel-to-Channel Matching 6
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity at Logic High
Output 7
Common-Mode Transient Immunity at Logic Low
Output7
Refresh Rate
Input Enable Time 8
Input Disable Time8
Input Dynamic Supply Current per Channel 9
Output Dynamic Supply Current per Channel9
Symbol
Min
IDD1 (Q)
IDD2 (Q)
IDD1 (10)
IDD2 (10)
IIA, IIB, IIC, IID, –10
ICTRL, IDISABLE
VIH
VIL
0.4
VOAH, VOBH, VDD1, VDD2 – 0.4
VOCH, VODH
VOAL, VOBL,
VOCL, VODL
Typ
Max Unit
Test Conditions
1.2
0.8
3.4
1.1
+0.01
1.6
1.0
4.9
1.3
+10
mA
mA
mA
mA
μA
VIA = VIB = VIC = VID = 0
VIA = VIB = VIC = VID = 0
5 MHz logic signal frequency
5 MHz logic signal frequency
0 ≤ VIA, VIB, VIC, VID, VDISABLE ≤ VDD1,
0 ≤ VCTRL ≤ VDD2
1.6
V
V
V
IOx = –4 mA, VIx = VIxH
0.4
V
IOx = +4 mA, VIx = VIxL
100
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1/VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
2.8
0.2
PW
tPSK
tPSKCD
tR/tF
|CMH|
25
2.5
35
ns
Mbps
ns
ns
ps/°C
ns
ns
ns
kV/μs
|CML|
25
35
kV/μs
tPHL, tPLH
PWD
10
20
30
50
5
5
30
5
fr
tENABLE
tDISABLE
IDDI (D)
IDDO (D)
1.1
2.0
5.0
0.10
0.03
1
Mbps
μs
μs
mA/Mbps
mA/Mbps
VIA, VIB, VIC, VID = 0 or VDD1
VIA, VIB, VIC, VID = 0 or VDD1
Supply current values are for all channels combined running at identical data rates. Output supply current values are specified with no output load present. The supply
current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. See Figure 4 through
Figure 6 for information on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See Figure 7 through Figure 8 for total
IDD1 and IDD2 supply currents as a function of the data rate.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels within the same component.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Input enable time is the duration from when VDISABLE is set low until the output states are guaranteed to match the input states in the absence of any input data logic
transitions. If an input data logic transition within a given channel does occur within this time interval, the output of that channel reaches the correct state within the
much shorter duration as determined by the propagation delay specifications within this data sheet. Input disable time is the duration from when VDISABLE is set high
until the output states are guaranteed to reach their programmed output levels, as determined by the CTRL logic state (see Table 9).
9
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 4 through Figure 6 for information
on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See the Power Consumption section for guidance on
calculating the per-channel supply current for a given data rate.
Rev. E | Page 4 of 16
ADuM1310
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3 V OR 3 V/5 V OPERATION
5 V/3 V operation 1 : 4.5 V ≤ VDD1 ≤ 5.5 V, 2.7 V ≤ VDD2 ≤ 3.6 V; 3 V/5 V operation: 2.7 V ≤ VDD1 ≤ 3.6 V, 4.5 V ≤ VDD2 ≤ 5.5 V;
all minimum/maximum specifications apply over the entire recommended operation range, unless otherwise noted; all typical
specifications are at TA = 25°C; VDD1 = 3.0 V, VDD2 = 5 V; or VDD1 = 5 V, VDD2 = 3.0 V.
Table 3.
Parameter
DC SPECIFICATIONS
ADuM1310, Total Supply Current, Three
Channels 2
VDD1 Supply Current, Quiescent
5 V/3 V Operation
3 V/5 V Operation
VDD2 Supply Current, Quiescent
5 V/3 V Operation
3 V/5 V Operation
VDD1 Supply Current, 10 Mbps Data Rate
5 V/3 V Operation
3 V/5 V Operation
VDD2 Supply Current, 10 Mbps Data Rate
5 V/3 V Operation
3 V/5 V Operation
Input Currents
Logic High Input Threshold
5 V/3 V Operation
3 V/5 V Operation
Logic Low Input Threshold
5 V/3 V Operation
3 V/5 V Operation
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 3
Maximum Data Rate 4
Propagation Delay 5
Pulse Width Distortion, |tPLH – tPHL|5
Change vs. Temperature
Propagation Delay Skew 6
Channel-to-Channel Matching 7
Output Rise/Fall Time (10% to 90%)
5 V/3 V Operation
3 V/5 V Operation
Common-Mode Transient Immunity at
Logic High Output 8
Common-Mode Transient Immunity at
Logic Low Output8
Symbol
Min
Typ
Max Unit
Test Conditions
2.4
1.2
3.2
1.6
mA
mA
VIA = VIB = VIC = VID = 0
VIA = VIB = VIC = VID = 0
0.8
1.2
1.0
1.6
mA
mA
VIA = VIB = VIC = VID = 0
VIA = VIB = VIC = VID = 0
6.5
3.4
8.2
4.9
mA
mA
5 MHz logic signal frequency
5 MHz logic signal frequency
1.1
1.9
+0.01
1.3
2.2
+10
mA
mA
μA
5 MHz logic signal frequency
5 MHz logic signal frequency
0 ≤ VIA, VIB, VIC, VID, VDISABLE ≤ VDD1,
0 ≤ VCTRL ≤ VDD2
2.0
1.6
V
V
IDDI (Q)
IDDO (Q)
IDD1 (10)
IDD2 (10)
IIA, IIB, IIC, IID, ICTRL,
IDISABLE
VIH
–10
VIL
VOAH, VOBH, VOCH,
VODH
VOAL, VOBL, VOCL,
VODL
0.8
0.4
VDD1/VDD2 − 0.4 VDD1/VDD2 − 0.2
0.2
PW
tPHL, tPLH
PWD
10
20
30
V
V
V
IOx = –4 μA, VIx = VIxH
0.4
V
IOx = +4 μA, VIx = VIxL
100
ns
Mbps
ns
ns
ps/°C
ns
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
ns
ns
kV/μs
kV/μs
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1/VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
50
5
5
tPSK
tPSKCD
tR/tf
30
5
|CMH|
25
3.0
2.5
35
|CML|
25
35
Rev. E | Page 5 of 16
ADuM1310
Parameter
Refresh Rate
5 V/3 V Operation
3 V/5 V Operation
Input Enable Time 9
Input Disable Time9
Input Dynamic Supply Current per
Channel 10
5 V/3 V Operation
3 V/5 V Operation
Output Dynamic Supply Current per
Channel10
5 V/3 V Operation
3 V/5 V Operation
Symbol
fr
Min
Typ
Max Unit
1.2
1.1
tENABLE
tDISABLE
IDDI (D)
2.0
5.0
Mbps
Mbps
μs
μs
0.19
0.10
mA/Mbps
mA/Mbps
0.03
0.05
mA/Mbps
mA/Mbps
Test Conditions
VIA, VIB, VIC, VID = 0 or VDD1
VIA, VIB, VIC, VID = 0 or VDD1
IDDO (D)
1
All voltages are relative to their respective ground.
Supply current values are for all channels combined running at identical data rates. Output supply current values are specified with no output load present. The supply
current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. See Figure 4 through
Figure 6 for information on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See Figure 7 through Figure 8 for total
IDD1 and IDD2 supply currents as a function of the data rate.
3
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
4
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
5
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
6
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
7
Channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels within the same component.
8
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
9
Input enable time is the duration from when VDISABLE is set low until the output states are guaranteed to match the input states in the absence of any input data logic
transitions. If an input data logic transition within a given channel does occur within this time interval, the output of that channel reaches the correct state within the
much shorter duration as determined by the propagation delay specifications within this data sheet. Input disable time is the duration from when VDISABLE is set high
until the output states are guaranteed to reach their programmed output levels, as determined by the CTRL logic state (see Truth Table – Table 9).
10
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 4 through Figure 6 for information
on the per-channel supply current as a function of the data rate for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating
the per-channel supply current for a given data rate.
2
Rev. E | Page 6 of 16
ADuM1310
PACKAGE CHARACTERISTICS
Table 4.
Parameter
Resistance (Input-to-Output) 1
Capacitance (Input-to-Output)2
Input Capacitance 2
IC Junction-to-Case Thermal Resistance, Side 1
Symbol
RI-O
CI-O
CI
θJCI
IC Junction-to-Case Thermal Resistance, Side 2
θJCO
1
2
Min
Typ
1012
2.2
4.0
33
28
Max
Unit
Ω
pF
pF
°C/W
°C/W
Test Conditions
f = 1 MHz
Thermocouple located at center of
package underside
Thermocouple located at center of
package underside
Device considered a 2-terminal device. Pin 1, Pin 2, Pin 3, Pin 4, Pin 5, Pin 6, Pin 7, and Pin 8 shorted together and Pin 9, Pin 10, Pin 11, Pin 12, Pin 13, Pin 14, Pin 15, and
Pin 16 shorted together.
Input capacitance is from any input data pin to ground.
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 5.
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol Value
2500
L(I01)
7.7 min
Unit Conditions
V rms 1-minute duration
mm
Measured from input terminals to output terminals,
shortest distance through air
8.1 min
mm
Measured from input terminals to output terminals,
shortest distance path along body
0.017 min mm
Insulation distance through insulation
>175
V
DIN IEC 112/VDE 0303 Part 1
IIIa
Material Group (DIN VDE 0110, 1/89, Table 1)
Minimum External Tracking (Creepage)
L(I02)
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
Rev. E | Page 7 of 16
ADuM1310
DIN EN 60747-5-2 (VDE 0884 PART 2) INSULATION CHARACTERISTICS
The ADuM1310 isolator is suitable for basic electrical isolation only within the safety limit data. Maintenance of the safety data is ensured
by means of protective circuits. The * marking on packages denotes DIN EN 60747-5-2 approval for 560 V peak working voltage.
Category I through Category IV listed in the characteristic column are per DIN EN 60747-5-2 definition.
Table 6.
Description
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤150 V rms
For Rated Mains Voltage ≤300 V rms
For Rated Mains Voltage ≤400 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110, Table 1)
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method b1
VIORM × 1.875 = VPR, 100% Production Test, tm = 1 sec, Partial Discharge <5 pC
Input-to-Output Test Voltage, Method A
After Environmental Tests Subgroup 1
VIORM × 1.6 = VPR, tm = 60 sec, Partial Discharge <5 pC
After Input and/or Safety Test Subgroup 2/3
VIORM × 1.2 = VPR, tm = 60 sec, Partial Discharge <5 pC
Highest Allowable Overvoltage (Transient Overvoltage, tTR = 10 sec)
Safety-Limiting Values (Maximum Value Allowed in the Event of a Failure; see Figure 2)
Case Temperature
Side 1 Current
Side 2 Current
Insulation Resistance at TS, VIO = 500 V
Symbol
Characteristic
Unit
VIORM
VPR
I to IV
I to III
I to II
40/105/21
2
560
1050
V peak
V peak
896
V peak
VTR
672
4000
V peak
V peak
TS
IS1
IS2
RS
150
265
335
>109
°C
mA
mA
Ω
VPR
350
250
SIDE #2
200
150
SIDE #1
100
50
0
0
50
100
150
CASE TEMPERATURE (°C)
200
04904-003
SAFETY-LIMITING CURRENT (mA)
300
Figure 2. Thermal Derating Curve, Dependence of Safety-Limiting Values with
Case Temperature per DIN EN 60747-5-2
RECOMMENDED OPERATING CONDITIONS
Table 7.
Parameter
Operating Temperature
Supply Voltages 1
Input Signal Rise and Fall Times
1
Symbol
TA
VDD1, VDD2
Min
–40
2.7
Max
+105
5.5
1.0
Unit
°C
V
ms
All voltages are relative to their respective ground. See the DC Correctness and Magnetic Field Immunity section for information on immunity to external magnetic fields.
Rev. E | Page 8 of 16
ADuM1310
ABSOLUTE MAXIMUM RATINGS
REGULATORY INFORMATION
TA = 25°C, unless otherwise noted.
In accordance with UL1577, each ADuM1310 is proof tested by
applying an insulation test voltage ≥3000 V rms for 1 second
(current leakage detection limit = 5 μA).
Table 8.
Parameter
Storage Temperature
Ambient Operating
Temperature
Supply Voltages1
Input Voltage1, 2
Output Voltage1, 2
Average Output Current per
Pin3
Side 1
Side 2
Common-Mode Transients4
Rating
–65°C to +150°C
–40°C to +105°C
In accordance with DIN EN 60747-5-2, each ADuM1310 is
proof tested by applying an insulation test voltage ≥1050 V peak
for 1 second (partial discharge detection limit = 5 pC).
–0.5 V to +6.5 V
–0.5 V to VDDI + 0.5 V
–0.5 VDDO + 0.5 V to VDDO + 0.5 V
The ADuM1310 is approved by the following organizations:
UL: Recognized under 1577 Component Recognition Program.
CSA: Approved under CSA Component Acceptance Notice #5A.
–18 mA to +18 mA
–22 mA to +22 mA
–100 kV/μs to +100 kV/μs
VDE: Certified according to
DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01, and
DIN EN 60950 (VDE 0805): 2001-12; EN 60950: 2000.
1
All voltages are relative to their respective ground.
VDDI and VDDO refer to the supply voltages on the input and output sides of a
given channel, respectively.
3
See Figure 2 for maximum rated current values for various temperatures.
4
Refers to common-mode transients across the insulation barrier. Commonmode transients exceeding the Absolute Maximum Ratings can cause latchup or permanent damage.
2
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions may affect device reliability.
Table 9. Truth Table (Positive Logic)
VIX
Input 1
H
L
X
X
X
CTRL
Input
X
X
H or NC
L
H or NC
VDISABLE
State
L or NC
L or NC
H
H
X
VDD1
State1
Powered
Powered
X
X
Unpowered
X
L
X
Unpowered Powered
X
X
X
Powered
1
VDD2
State1
Powered
Powered
Powered
Powered
Powered
VOX
Output1
H
L
H
L
H
L
Unpowered Z
Notes
Normal operation, data is high.
Normal operation, data is low.
Inputs disabled. Outputs are in the default state as determined by CTRL.
Inputs disabled. Outputs are in the default state as determined by CTRL.
Input unpowered. Outputs are in the default state as determined by CTRL.
Outputs return to input state within 1 μs of VDD1 power restoration.
See the Power-Up/Power-Down Considerations section for more details.
Input unpowered. Outputs are in the default state as determined by CTRL.
Outputs return to input state within 1 μs of VDD1 power restoration.
See the Power-Up/Power-Down Considerations section for more details.
Output unpowered. Output pins are in high impedance state.
Outputs return to input state within 1 μs of VDD2 power restoration.
See the Power-Up/Power-Down Considerations section for more details.
VIX and VOX refer to the input and output signals of a given channel (A, B, C, or D).
Rev. E | Page 9 of 16
ADuM1310
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
VDD1 1
16 VDD2
GND1* 2
15 GND2*
VIA 3
ADuM1310
VIB 4
TOP VIEW
(Not to Scale)
VIC 5
NC 6
DISABLE 7
14 VOA
13 VOB
12 VOC
11 NC
10 CTRL
GND1* 8
9
GND2*
*PIN 2 AND PIN 8 ARE INTERNALLY CONNECTED. CONNECTING BOTH
TO GND1 IS RECOMMENDED. PIN 9 AND PIN 15 ARE INTERNALLY
CONNECTED. CONNECTING BOTH TO GND2 IS RECOMMENDED.
04904-004
NC = NO CONNECT
Figure 3. Pin Configuration
Table 10. ADuM1310 Pin Function Descriptions
Pin No.
1
2
Mnemonic
VDD1
GND1
3
4
5
6
7
VIA
VIB
VIC
NC
DISABLE
8
GND1
9
GND2
10
CTRL
11
12
13
14
15
NC
VOC
VOB
VOA
GND2
16
VDD2
Description
Supply Voltage for Isolator Side 1, 2.7 V to 5.5 V.
Ground 1. Ground reference for Isolator Side 1. Pin 2 and Pin 8 are internally connected; connecting both
pins to GND1 is recommended.
Logic Input A.
Logic Input B.
Logic Input C.
No Connect.
Input Disable. Disables the isolator inputs and refreshes. Outputs take on logic state determined
by CTRL.
Ground 1. Ground reference for Isolator Side 1. Pin 8 and Pin 2 are internally connected; connecting both
pins to GND1 is recommended.
Ground 2. Ground reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected; connecting both
pins to GND2 is recommended.
Default Output Control. Controls the logic state the outputs take on when the input power is off. VOA,
VOB, and VOC outputs are high when CTRL is high or disconnected and VDD1 is off. VOA, VOB, and VOC
outputs are low when CTRL is low and VDD1 is off. When VDD1 power is on, this pin has no effect.
No Connect.
Logic Output C.
Logic Output B.
Logic Output A.
Ground 2. Ground reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected; connecting both
pins to GND2 is recommended.
Supply Voltage for Isolator Side 2, 2.7 V to 5.5 V.
Rev. E | Page 10 of 16
ADuM1310
TYPICAL PERFORMANCE CHARACTERISTICS
2.5
7
6
5
CURRENT (mA)
CURRENT/CHANNEL (mA)
2.0
1.5
1.0
5V
3V
4
3
3V
5V
2
0.5
0
2
4
6
DATA RATE (Mbps)
8
10
0
04904-006
0
0
2
4
6
DATA RATE (Mbps)
8
10
04904-009
1
Figure 7. Typical ADuM1310 VDD1 Supply Current vs.
Data Rate for 5 V and 3 V Operation
Figure 4. Typical Supply Current per Input Channel vs.
Data Rate for 5 V and 3 V Operation
2.5
0.7
0.6
0.5
CURRENT (mA)
CURRENT/CHANNEL (mA)
2.0
0.4
5V
0.3
3V
1.5
5V
1.0
3V
0.2
0.5
0
2
4
6
DATA RATE (Mbps)
8
10
1.2
0.8
0.6
3V
0.4
0.2
0
2
4
6
DATA RATE (Mbps)
8
10
04904-008
CURRENT/CHANNEL (mA)
1.0
0
0
2
4
6
DATA RATE (Mbps)
8
Figure 8. Typical ADuM1310 VDD2 Supply Current vs.
Data Rate for 5 V and 3 V Operation
Figure 5. Typical Supply Current per Output Channel vs.
Data Rate for 5 V and 3 V Operation (No Output Load)
5V
0
Figure 6. Typical Supply Current per Output Channel vs.
Data Rate for 5 V and 3 V Operation (15 pF Output Load)
Rev. E | Page 11 of 16
10
04904-010
0
04904-007
0.1
ADuM1310
APPLICATION INFORMATION
PC BOARD LAYOUT
The ADuM1310 digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins (see
Figure 9). Bypass capacitors are most conveniently connected
between Pin 1 and Pin 2 for VDD1 and between Pin 15 and Pin 16
for VDD2. The capacitor value should be between 0.01 μF and
0.1 μF. The total lead length between both ends of the capacitor
and the input power supply pin should not exceed 20 mm.
Bypassing between Pin 1 and Pin 8 and between Pin 9 and
Pin 16 should also be considered unless the ground pair on
each package side is connected close to the package.
VDD2
GND2
VOA
VOB
VOC
NC
CTRL
GND2
NC = NO CONNECT
Figure 9. Recommended Printed Circuit Board Layout
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the length of
time it takes for a logic signal to propagate through a component.
The input to output propagation delay time for a high to low
transition may differ from the propagation delay time of a low
to high transition.
INPUT (VIx)
V = (−dβ/dt)∑ π rn2; n = 1, 2, … , N
tPHL
04904-014
OUTPUT (VOx)
Positive and negative logic transitions at the isolator input
cause narrow (~1 ns) pulses to be sent via the transformer to
the decoder. The decoder is bistable, and is, therefore, either set
or reset by the pulses indicating input logic transitions. In the
absence of logic transitions at the input for more than 2 μs, a
periodic set of refresh pulses indicative of the correct input state
are sent to ensure dc correctness at the output. If the decoder
receives no pulses for more than about 5 μs, the input side is
assumed to be unpowered or nonfunctional, in which case, the
isolator output is forced to a default state (see Table 9) by the
watchdog timer circuit.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold of about 0.5 V,
therefore establishing a 0.5 V margin in which induced voltages
can be tolerated. The voltage induced across the receiving coil is
given by
50%
tPLH
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
The magnetic field immunity of the ADuM1310 is determined by
the changing magnetic field which induces a voltage in the transformer’s receiving coil large enough to either falsely set or reset
the decoder. The following analysis defines the conditions
under which this can occur. The ADuM1310’s 3 V operating
condition is examined because it represents the most
susceptible mode of operation.
04904-013
VDD1
GND1
VIA
VIB
VIC
NC
DISABLE
GND1
Propagation delay skew refers to the maximum amount
the propagation delay differs among multiple ADuM1310
components operated under the same conditions.
50%
Figure 10. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
where:
β is the magnetic flux density (gauss).
N is the number of turns in the receiving coil.
rn is the radius of the nth turn in the receiving coil (cm).
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM1310 component.
Rev. E | Page 12 of 16
ADuM1310
Given the geometry of the receiving coil in the ADuM1310 and
an imposed requirement that the induced voltage be at most
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field at a given frequency can be calculated. The result
is shown in Figure 11.
MAXIMUM ALLOWABLE MAGNETIC FLUX
DENSITY (kgauss)
100
POWER CONSUMPTION
The supply current at a given channel of the ADuM1310
isolator is a function of the supply voltage, the data rate of the
channel, and the output load of the channel.
10
1
For each input channel, the supply current is given by
1
0.01
10k
1M
10M
100k
MAGNETIC FIELD FREQUENCY (Hz)
100M
Figure 11. Maximum Allowable External Magnetic Flux Density
f ≤ 0.5fr
IDDI = IDDI (D) × (2f – fr) + IDDI (Q)
f > 0.5fr
The preceding magnetic flux density values correspond to specific
current magnitudes at given distances away from the ADuM1310
transformers. Figure 12 expresses these allowable current magnitudes as a function of frequency for selected distances. As
can be seen, the ADuM1310 is extremely immune and can be
affected only by extremely large currents operated at high frequency, very close to the component. For the 1 MHz example
noted, a 0.5 kA current needed to be placed 5 mm away from
the ADuM1310 to affect the operation of the component.
1000
DISTANCE = 1m
100
f is the input logic signal frequency (Hz, half of the input data
rate, NRZ signaling).
fr is the input stage refresh rate (bps).
IDDI (Q), IDDO (Q) are the specified input and output quiescent
supply currents (mA).
To calculate the total IDD1 and IDD2 supply current, the supply
currents for each input and output channel corresponding to
IDD1 and IDD2 are calculated and totaled. Figure 4 and Figure 5
provide per-channel supply currents as a function of the data
rate for an unloaded output condition. Figure 6 provides perchannel supply current as a function of the data rate for a 15 pF
output condition. Figure 7 through Figure 8 provide total IDD1
and IDD2 supply current as a function of the data rate for the
ADuM1310.
DISTANCE = 5mm
1M
10M
100M
04904-016
0.1
100k
f ≤ 0.5fr
VDDO is the output supply voltage (V).
1
MAGNETIC FIELD FREQUENCY (Hz)
IDDO = (IDDO (D) + CLVDDO) × (2f – fr) + IDDO (Q)
CL is the output load capacitance (pF).
DISTANCE = 100mm
10k
f ≤ 0.5fr
IDDI (D), IDDO (D) are the input and output dynamic supply currents
per channel (mA/Mbps).
10
0.01
IDDO = IDDO (Q)
where:
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.2 kgauss induces a
voltage of 0.25 V at the receiving coil. This is approximately
50% of the sensing threshold and does not cause a faulty output
transition. Similarly, if such an event occurs during a transmitted
pulse (and is of the worst-case polarity), it reduces the received
pulse from >1.0 V to 0.75 V—still well above the 0.5 V sensing
threshold of the decoder.
1k
IDDI = IDDI (Q)
For each output channel, the supply current is given by
04904-015
0.001
1k
MAXIMUM ALLOWABLE CURRENT (kA)
Note that at combinations of strong magnetic field and high
frequency, any loops formed by printed circuit board traces
could induce sufficiently large error voltages to trigger the
thresholds of succeeding circuitry. Care should be taken in the
layout of such traces to avoid this possibility.
Figure 12. Maximum Allowable Current for Various
Current-to-ADuM1310 Spacings
Rev. E | Page 13 of 16
ADuM1310
POWER-UP/POWER-DOWN CONSIDERATIONS
Given that the ADuM1310 has separate supplies on either side
of the isolation barrier, the power-up and power-down
characteristics relative to each supply voltage need to be
considered individually.
When VDD1 crosses the threshold for activating the refresh
circuit (approximately 2 V), there can be a delay of up to 2 μs
before the output is updated to the correct state, depending on
the timing of the next refresh pulse. When VDD1 is reduced from
an on state below the 2 V threshold, there can be a delay of up
to 5 μs before the output takes on its default state determined by
the CTRL signal. This corresponds to the duration that the
watchdog timer circuit at the input is designed to wait before
triggering an output default state.
As shown in Table 9, when VDD1 input power is off, the
ADuM1310 outputs take on a default condition as determined
by the state of the CTRL pin. As the VDD1 supply is
increased/decreased, the output of each channel transitions
from/to the default condition to/from the state matching its
respective signals (see Figure 13 and Figure 14).
OUTPUT
DATA
When the VDD2 output supply is below the level at which the
ADuM1310 output transistors are biased (about 1 V), the
outputs take on a high impedance state. When VDD2 is above a
value of about 2 V, each channel output takes on a state
matching that of its respective input. Between the values of 1 V
and 2 V, the outputs are set low. This behavior is shown in
Figure 15 and Figure 16.
OUTPUT
DATA
VDD1
VDD1
CTRL = HIGH OR NC
CTRL = LOW
04904-017
2V
(TYP)
Figure 13. VDD1 Power-Up/Power-Down Characteristics, Input Data = High
2V
(TYP)
OUTPUT
DATA
VDD1
HIGH
IMPEDANCE
VDD1
VDD2
HIGH
IMPEDANCE
04904-019
OUTPUT
DATA
Figure 15. VDD2 Power-Up/Power-Down Characteristics, Input Data = High
2V
(TYP)
04904-018
OUTPUT DATA
CTRL = HIGH OR NC
CTRL = LOW
Figure 14. VDD1 Power-Up/Power-Down Characteristics, Input Data = Low
2V
(TYP)
HIGH
IMPEDANCE
VDD2
HIGH
IMPEDANCE
Figure 16. VDD2 Power-Up/Power-Down Characteristics, Input Data = Low
Rev. E | Page 14 of 16
04904-020
OUTPUT
DATA
ADuM1310
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.50 (0.0197)
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
45°
8°
0°
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
060606-A
1
Figure 17. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body (RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
ADuM1310BRWZ 1
ADuM1310BRWZ-RL1, 2
1
2
Number of
Channels
3
3
Maximum Data
Rate (Mbps)
10
10
Temperature Range
−40°C to +105°C
−40°C to +105°C
Z = Pb-free part.
The addition of an -RL suffix designates a 13-inch (1,000 units) tape and reel option.
Rev. E | Page 15 of 16
Package Description
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
Package Option
RW-16
RW-16
ADuM1310
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04904-0-10/06(E)
Rev. E | Page 16 of 16