Hybrid Aluminum Electrolytic Capacitors NSPE-T Series • CYLINDRICAL V-CHIP CONSTRUCTION FOR SURFACE MOUNTING • EXTENDED LOAD LIFE AT HIGH TEMPERATURE (1,500 ~ 3,000 HOURS @ +125°C) • HIGH VOLTAGE RATINGS (16 ~ 125VDC) • LOW ESR AND HIGH RIPPLE CURRENT RATINGS • 6.3x6.3mm ~ 10x12.8mm CASE SIZES • REFLOW SOLDERING RATED TO +260°C (+250°C 80V & 125V) • MEETS THE REQUIREMENTS OF AEC-Q200* *Contact NIC for supporting test data CHARACTERISTICS Rated Voltage Range Rated Capacitance Range Operating Temp. Range Capacitance Tolerance Max. Leakage Current After 2 Minutes @ 20°C 16 ~ 125Vdc 6.8 ~ 560μF -55 ~ +125°C ±20% (M) 16 ~ 63Vdc 80 ~ 125Vdc W.V. (Vdc) S.V. (Vdc) 0.01CV Less than 0.05CV or 100μA whichever is greater 16 25 35 40 50 63 80 100 125 Working and Surge Voltage Ratings 20 32 44 50 63 79 100 125 157 Tan δ @ 120Hz/20°C 0.16 Z -55°C/Z +20°C 1 ~ 2.5 Impedance Ratio Z +125°C/Z +20°C 0.6 ~ 1.0 W.V. (Vdc) 16 25 35 40 50 63 80 100 125 16V φ6.3 = 1,500 hrs, φ8 & 10 = 2500 hrs. Case Dia. 25V & up 6.3X6.3 = 1500 hrs, 6.3X8 = 2000 hrs, φ8 & 10 = 3000 hrs. Load Life Test @ 125°C Capacitance Change Within ±30% of initial measured value and Rated Voltage Tan δ and ESR Less than 200% of specified max. value Leakage Current Less than specified max. value ESR Less than 200% of specified max. value Hot Plate at +250°C for 30 seconds with electrodes facing downward Capacitance Change Within ±10% of the initial measured value Resistance to Soldering Heat Dissipation Factor Less than the initial limit Leakage Current Less then the initial limit ESR Less than 130% of specified value STANDARD PRODUCTS AND CASE SIZES Dφ x L (mm) NSPE-T121M16V6.3X8NBF Cap. Working Case Size Max. Tan δ Max. ESR (mΩ) Max. Ripple Current (mA rms) Load Life (μF) Voltage (D X L) mm 120Hz/20°C AT 100kHz/20°C AT 100KHz/125°C Hours (+125°C) 120 6.3X8 0.16 40 1160 1500 NSPE-T271M16V8X10.8NBF 270 NSPE-T471M16V10X10.8NBF 470 NSPE-T561M16V10X12.8NBF 560 NSPE-T470M25V6.3X6.3NBF NSPE-T680M25V6.3X8NBF PART NUMBER 8X10.8 0.16 26 1540 2500 10X10.8 0.16 21 2010 2500 10X12.8 0.16 15 2320 2500 47 6.3X6.3 0.16 60 890 1500 68 6.3X8 0.16 45 980 2000 16 NSPE-T151M25V8X10.8NBF 150 8X10.8 0.16 27 1330 3000 NSPE-T271M25V10X10.8NBF 270 10X10.8 0.16 22 1520 3000 NSPE-T331M25V10X12.8NBF 330 10X12.8 0.16 16 1740 3000 NSPE-T270M35V6.3X6.3NBF 27 6.3X6.3 0.16 100 760 1500 NSPE-T470M35V6.3X8NBF 47 NSPE-T101M35V8X10.8NBF 100 NSPE-T151M35V10X10.8NBF NSPE-T221M35V10X12.8NBF 25 6.3X8 0.16 60 910 2000 8X10.8 0.16 30 1260 3000 150 10X10.8 0.16 23 1480 3000 220 10X12.8 0.16 17 1700 3000 NSPE-T180M40V6.3X6.3NBF 18 6.3X6.3 0.16 110 720 1500 NSPE-T270M40V6.3X8NBF 27 6.3X8 0.16 70 870 2000 NSPE-T560M40V8X10.8NBF 56 NSPE-T101M40V10X10.8NBF 100 35 40 8X10.8 0.16 32 1220 3000 10X10.8 0.16 24 1440 3000 NSPE-T121M40V10X12.8NBF 120 10X12.8 For Automotive Applications See Part Numbering System 0.16 18 1650 3000 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 1 Hybrid Aluminum Electrolytic Capacitors NSPE-T Series STANDARD PRODUCTS AND CASE SIZES Dφ x L (mm) PART NUMBER NSPE-T100M50V6.3X6.3NBF NSPE-T150M50V6.3X8NBF Cap. Working Case Size Max. Tan δ Max. ESR (mΩ) Max. Ripple Current (mA rms) Load Life (μF) Voltage (D X L) mm 120Hz/20°C AT 100kHz/20°C AT 100KHz/125°C Hours (+125°C) 10 6.3X6.3 0.16 120 690 1500 15 6.3X8 50 0.16 80 840 2000 NSPE-T330M50V8X10.8NBF 33 8X10.8 0.16 35 1170 3000 NSPE-T560M50V10X10.8NBF 56 10X10.8 0.16 25 1390 3000 NSPE-T820M50V10X12.8NBF 82 10X12.8 0.16 19 1590 3000 NSPE-T6R8M63V6.3X6.3NBF 6.8 6.3X6.3 0.16 150 670 1500 NSPE-T100M63V6.3X8NBF 10 6.3X8 0.16 100 740 2000 NSPE-T220M63V8X10.8NBF 22 8X10.8 0.16 40 1090 3000 NSPE-T330M63V8X10.8NBF 33 8X10.8 0.16 40 1090 3000 NSPE-T330M63V10X10.8NBF 33 10X10.8 0.16 30 1260 3000 NSPE-T470M63V10X10.8NBF 47 10X10.8 0.16 30 1260 3000 NSPE-T560M63V10X12.8NBF 56 10X12.8 0.16 22 1440 3000 NSPE-T120M80V10X10.8LBF 12 10X10.8 0.16 70 900 3000 NSPE-T150M80V10X10.8LBF 15 10X10.8 0.16 70 900 3000 3000 63 80 NSPE-T180M80V10X12.8LBF 18 10X12.8 0.16 50 1100 NSPE-T100M100V10X10.8LBF 10 10X10.8 0.16 80 870 3000 NSPE-T120M100V10X10.8LBF 12 10X10.8 0.16 80 870 3000 NPSE-T150M100V10X12.8LBF 15 10X12.8 0.16 60 1000 3000 NSPE-T100M125V10X10.8LBF 10 10X10.8 0.16 90 750 3000 100 125 For Automotive Applications See Part Numbering System RIPPLE CURRENT FREQUENCY CORRECTION FACTOR Frequency 6.8 ~ 33μF 47 ~ 560μF 100Hz 0.05 0.10 1KHz 0.32 0.35 10KHz 0.67 0.70 100KHz 1.0 1.0 DIMENSIONS (mm) Case Size 6.3x6.3 6.3x8 8x10.8 10x10.8 10x12.8 Dφ ±0.5 6.3 6.3 8.0 10 10 L max. 6.3 8.0 10.8 10.8 12.8 A, B ±0.2 6.6 6.6 8.3 10.3 10.3 W 0.5 ~ 0.8 0.5 ~ 0.8 0.7 ~ 1.0 1.0 ~ 1.4 1.0 ~ 1.4 + Dφ I I ±0.2 2.5 2.5 2.9 3.2 3.2 I - W 0.3mm max. Part Marking P ±0.2 2.2 2.2 3.2 4.6 4.6 Series Code Lot Code T__ 6R8 63V Capacitance Value A L Voltage P B 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Hybrid Aluminum Electrolytic Capacitors NSPE-T Series PART NUMBER SYSTEM NSPE-T 220 M 63V 8x10.8 N B Y F Series RoHS Compliant B=Sn-Bi Finish & 13" Reel, L=Sn-Bi Finish & 15" Reel Reflow Temp. Code (N=+260°C, L=+250°C) Size in mm Working Voltage Tolerance Code M=20% Capacitance Code in μF, first 2 digits are significant Third digit is no. of zeros, “R” indicates decimal for values under 10μF Optional: Suitable for automotive equipment, sourced to special production and inspection at TS-16949 certified production site LAND PATTERN DIM. (mm) Temperature - Deg. C RECOMMENDED REFLOW SOLDERING PROFILE* 260 230 200 Time Above 230°C (40 seconds max.) 150 100 Case Dia. 6.3 8 10 Peak Temperature (260°C/5 seconds) Time Above 200°C (80 seconds max.) A 3.6 4.1 4.4 B 1.8 2.1 2.5 + P 1.8 2.8 4.3 - Preheat - 120 seconds max. (+150°C ~ +190°C) B 50 Time (Seconds) A P A PEAK TEMPERATURE AND DURATION Rated Voltage/Diameter Time Above +200°C Time Above +217°C Time Above +230°C 16V ~ 63V / 6.3mm ~ 10mm 100 sec. max. 80 sec. max. 40 sec. max. 80 ~ 125V / 10mm *Two reflow passes are permissible with a cool down to room temperature required between the first and second pass. NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com Peak Temperature +260°C (5 sec. max.) +250°C (5 sec. max.) www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 3 Hybrid Aluminum Electrolytic Capacitors NSPE-T Series TAPING SPECIFICATIONS (mm) 1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets. 2. Leader tape: Approximately 20cm of cover tape at leader. 4 + 0.1 3. Connection: Maximum 3 connections (slices) per reel. D ±0.1 7.5 7.5 11.5 11.5 11.5 P ±0.1 12.0 12.0 16.0 16.0 16.0 T ±0.2 6.5 8.2 11.0 11.0 13.3 t max. 0.6 0.6 0.6 0.6 0.6 6.3x6.3 6.3x8 8x10.5 10x10.5 10x12.8 W ±1.0 18 18 26 26 26 + A P Feeding T 2mm ± 0.5mm REEL DIMENSIONS (mm) Case Size - B C ±0.3 16.0 16.0 24.0 24.0 24.0 D B ±0.5 7.0 7.0 8.7 10.7 10.7 t Qty per Reel 13" (330mm) 15" (380mm) 800 1000 500 900 300 500 300 500 300 400 φ13mm ± 0.5mm φ50mm min. 6.3x6.3 6.3x8 8x10.8 10x10.8 10x12.8 A ±0.5 7.0 7.0 8.7 10.7 10.7 1.75 ± C Case Size 1.75 + 0.15 1.5∅ +0.1/1.5φ+0.1/-0 φ21mm ± 0.8mm φ330mm ± 2.0mm or φ380mm ± 2.0mm 4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com W www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE 3mm www.SMTmagnetics.com