Hybrid Aluminum Electrolytic Capacitors NSPE-A Series • CYLINDRICAL V-CHIP CONSTRUCTION FOR SURFACE MOUNTING • EXTENDED LOAD LIFE AT HIGH TEMPERATURE (10,000 HOURS @ +105°C) • HIGH VOLTAGE RATINGS (25 ~ 80VDC) • LOW ESR AND HIGH RIPPLE CURRENT RATINGS RoHS • 5x6.1mm ~ 10x10.5mm CASE SIZES Compliant includes all homogeneous materials • REFLOW SOLDERING RATED UP TO +260°C • MEETS THE REQUIREMENTS OF AEC-Q200* *See Part Number System for Details *Contact NIC for supporting test data CHARACTERISTICS Rated Voltage Range 25 ~ 80Vdc Rated Capacitance Range 10 ~ 330µF Operating Temp. Range -55 ~ +105°C Capacitance Tolerance ±20% (M) Max. Leakage Current After 2 Minutes @ 20°C W.V. (Vdc) Working and Surge Voltage Ratings S.V. (Vdc) Tan δ @ 120Hz/20°C Z -25°C/Z +20°C Impedance Ratio Z -55°C/Z +20°C Capacitance Change Load Life Test @ 105°C and Rated Voltage Tan δ and ESR (10,000 hours) Leakage Current 25 32 0.14 Less than 0.01CV or 3µA whichever is greater 35 50 63 44 63 79 0.12 0.10 0.08 2 2.5 Within ±30% of initial measured value Less than 200% of specified max. value Less than specified max. value 80 100 0.08 STANDARD PRODUCTS AND CASE SIZES Dφ x L (mm) PART NUMBER NSPE-A330M25V5X6.1NLBYF Cap. Working Case Size Max. Tan δ Max. ESR (mΩ) Max. Ripple Current (mA rms) (μF) Voltage (D X L) mm 120Hz/20°C AT 100KHz/20°C AT 100KHz/105°C 33 5X6.1 0.14 80 900 NSPE-A560M25V6.3X6.1NLBYF 56 NSPE-A101M25V6.3X8NLBYF 100 NSPE-A221M25V8X10.5NLBYF Load Life Hours 10,000 6.3X6.1 0.14 50 1300 10,000 6.3x8 0.14 30 2000 10,000 220 8x10.5 0.14 27 2300 10,000 NSPE-A331M25V10X10.5NLBYF 330 10x10.5 0.14 20 2500 10,000 NSPE-A220M35V5X6.1NLBYF 22 5X6.1 0.12 100 900 10,000 NSPE-A270M35V6.3X6.1NLBYF 27 6.3X6.1 0.12 60 1300 10,000 6.3X6.1 0.12 60 1300 10,000 6.3x8 0.12 35 2000 10,000 25 NSPE-A470M35V6.3X6.1NLBYF 47 NSPE-A680M35V6.3X8NLBYF 68 NSPE-A151M35V8X10.5NLBYF 150 8x10.5 0.12 27 2300 10,000 NSPE-A271M35V10X10.5NLBYF 270 10x10.5 0.12 20 2500 10,000 35 NSPE-A100M50V5X6.1NLBYF 10 5X6.1 0.1 120 750 10,000 NSPE-A220M50V6.3X6.1NLBYF 22 6.3X6.1 0.1 80 1100 10,000 NSPE-A330M50V6.3X8NLBYF 33 6.3X8 0.1 40 1600 10,000 NSPE-A680M50V8X10.5NLBYF 68 8X10.5 0.1 30 1800 10,000 NSPE-A101M50V10X10.5NLBYF 100 10X10.5 0.1 28 2000 10,000 NSPE-A100M63V6.3X6.1NLBYF 10 6.3X6.1 0.08 120 1000 10,000 NSPE-A220M63V6.3X8NLBYF 22 6.3X8 0.08 80 1500 10,000 NSPE-A330M63V8X10.5NLBYF 33 8X10.5 0.08 40 1700 10,000 50 63 NSPE-A560M63V10X10.5NLBYF 56 10X10.5 0.08 30 1800 10,000 NSPE-A220M80V8X10.5NLBYF 22 8x10.5 0.08 45 1550 10,000 NSPE-A330M80V10X10.5NLBYF 33 10X10.5 0.08 36 1700 10,000 80 RIPPLE CURRENT FREQUENCY CORRECTION FACTORS Frequency Correction Factor 120Hz 0.1 1KHz 0.3 10KHz 0.60 100KHz 1.00 PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Hybrid Aluminum Electrolytic Capacitors NSPE-A Series PART NUMBER SYSTEM NSPE-A 330 M 63V 8x10.5 N LB W Y F RoHS Compliant Wide Termination Option (>8mm diameter and larger) LB=Sn-Bi Finish, 15" Reel Series Reflow Temp. Code (N=+260°C) Size in mm Working Voltage Tolerance Code M=20% Capacitance Code in µF, first 2 digits are significant Third digit is no. of zeros, “R” indicates decimal for values under 10µF Suitable for automotive equipment, sourced to special production and inspection at TS-16949 certified production site DIMENSIONS (mm) Case Size 5X6.1 6.3X6.1 6.3X8 8X10.5 10X10.5 Dφ ±0.5 5 6.3 6.3 8.0 10 L max. 6.1 6.1 8.0 10.5 10.5 A, B ±0.2 5.3 6.6 6.6 8.3 10.3 W 0.55 ~ 0.75 0.55 ~ 0.75 0.55 ~ 0.75 0.7 ~ 1.1 0.7 ~ 1.1 + Dφ I I ±0.2 2.2 2.6 2.6 3.4 3.5 I P ±0.2 1.5 1.8 1.8 3.1 4.6 Part Marking Capacitane Code Voltage Code - 33 E ZA W 25V 35V 50V 63V 80V A L 0.3mm max. E V H J K Series P "L" does not include termination deflections Date Code B PEAK TEMPERATURE AND DURATION Diameter Time above 200°C Time above 217°C Time above 230°C 70 sec. max. 40 sec. max. 30 sec. max. f5 ~ 6.3mm f8 ~ 10mm Duration at Temperature >250°C = 5 sec. >250°C = 10 sec. >250°C = 5 sec. >240°C = 10 sec. Peak Temperature 260°C 255°C 260°C 245°C Allowable Reflow Passes 2 2 1 2 For f5 ~ 6.3mm diameter parts: 1. If peak temperature is +260°C the maximum time above +250°C is 5 seconds (maximum of two reflow passes). 2. If peak temperature is +255°C the maximum time above +250°C is 10 seconds (maximum of two reflow passes). For f8 ~ 10mm diameter parts: 1. If peak temperature is +260°C the maximum time above +250°C is 5 seconds (maximum of one reflow pass). 2. If peak temperature is +245°C the maximum time above +240°C is 10 seconds (maximum of two reflow passes). Temperature - Deg. C RECOMMENDED REFLOW SOLDERING PROFILE* Peak Temperature (see table) 260 230 200 Time Above 230°C (see table) 150 100 Time Above 200°C (see table) Preheat - 120 seconds max. (150°C ~ 190°C) 50 Time (Seconds) 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Hybrid Aluminum Electrolytic Capacitors STANDARD TERMINATION LAND PATTERN DIM. (mm) Case Diameter 5 6.3 8 10 A 1.5 1.8 3.1 4.6 B 2.8 3.2 4.0 4.1 C 1.6 1.6 2.0 2.0 NSPE-A Series + c b a b WIDE TERMINATION LAND PATTERN DIM. (mm) WIDE TERMINATION DIM. (mm) Case Size Dφ ±0.5 L max. A, B 8 x 10.5WT 8.0 10.8 8.3 ± 0.2 10 x 10.5WT 10.0 10.8 10.3 ± 0.2 C max. 10.0 12.0 P (3.1) (4.6) C W R T 1.2 ± 0.2 0.7 ± 0.2 1.3 ± 0.2 1.2 ± 0.2 0.7 ± 0.2 1.3 ± 0.2 Case Size 8x10.5 10x10.5 Dφ W A b 4.5 4.8 c 4.7 4.7 a WT Anti-Vibration Skirt L T c R R a 2.5 3.8 b P Termination deflection: WT = 0.15mm max. from bottom of support terminals B Review & Compare Reflow Soldering Heat Limits V-chip SMT Aluminum Electrolytic Capacitors www.niccomp.com/RSL 3 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Hybrid Aluminum Electrolytic Capacitors NSPE-A Series Taping Specifications (mm) 1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets. 2. Leader tape: Approximately 20cm of cover tape at leader. 3. Connection: Maximum 3 connections (slices) per reel. 4 + 0.1 P ±0.1 12.0 12.0 12.0 16.0 16.0 T ±0.2 6.4 6.4 8.4 11.0 11.0 t max. 0.4 0.4 0.4 0.4 0.4 REEL DIMENSIONS (mm) Case Size 5X6.1 6.3X6.1 6.3X8 8X10.5 10X10.5 W ±1.0 14 18 18 26 26 - + A P Feeding T 2mm ± 0.5mm Qty per Reel 15" (380mm) 1,000 1,000 900 500 500 φ13mm ± 0.5mm φ21mm ± 0.8mm φ380mm ± 2.0mm 4 t B D ±0.1 5.5 7.5 7.5 11.5 11.5 D C ±0.3 12.0 16.0 16.0 24.0 24.0 φ50mm min. 5X6.1 6.3X6.1 6.3X8 8X10.5 10X10.5 B ±0.5 5.7 7.0 7.0 8.7 10.7 1.75 ± C Case Size A ±0.5 5.7 7.0 7.0 8.7 10.7 1.75 + 0.15 1.5∅ +0.1/1.5φ+0.1/-0 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com W www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE 3mm www.SMTmagnetics.com