User’s Guide NHD-320240WG-BxFTI-VZ# LCM (Liquid Crystal Display Graphic Module) RoHS Compliant NHD320240WGB xFTIVZ#- Newhaven Display 320 x 240 pixels Display Type: Graphic Model serial number: B, x: New IC rev. White CCFL B/L FSTN-(negative) Transmissive, 6:00 View, Wide Temperature (-20 ~ +70c) Negative voltage generator on board For product support, contact Newhaven Display International 2511 Technology Drive, #101 Elgin, IL 60124 Tel: (847) 844-8795 Fax: (847) 844-8796 March12, 2009 Contents 1. Module classification information 2. Precautions in Use of LCM 3. General Specification 4. Absolute Maximum Ratings 5. Electrical Characteristics 6. Optical Characteristics 7. Interface Description 8. Contour Drawing & Block Diagram 9. Timing Characteristics 10. Reliability 11. Backlight Information 12. Inspection specification Newhaven Display International Page 2 of 18 NHD-320240-WG- B x F T I - V Z # 1.Module Classification Information NHD 3 2 0 2 4 0 WG᧩ Bx F T I᧩ c d e f VZ# ghi j c Brand᧶NEWHAVEN DISPLAY INTERNATIONAL, LLC. d Display Font᧶320 * 240 Dots e Display Type᧶HൺCharacter Type, GൺGraphic Type f Model serials number: B, x: New IC rev. g Backlight Type᧶ NൺWithout backlight h LCD Mode᧶ AൺLED, Amber BൺEL, Blue green RൺLED, Red DൺEL, Green OൺLED, Orange WൺEL, White GൺLED, Green FൺCCFL, White TൺLED, White YൺLED, Yellow Green SൺLED, Bright White BൺTN Positive, Gray TൺFSTN Negative NൺTN Negative, MൺSTN Negative, Blue GൺSTN Positive, Gray FൺFSTN Positive YൺSTN Positive, Yellow Green i LCD Polarizer Type/ Temperature range/ View direction j Special Code AൺReflective, N.T, 6:00 HൺTransflective, W.T,6:00 DൺReflective, N.T, 12:00 KൺTransflective,W.T,12:00 GൺReflective, W. T, 6:00 CൺTransmissive, N.T,6:00 JൺReflective, W. T, 12:00 FൺTransmissive, N.T,12:00 BൺTransflective, N.T,6:00 IൺTransmissive, W. T, 6:00 EൺTransflective, N.T.12:00 LൺTransmissive, W.T,12:00 VZ : Negative voltage generator on board # : RoHS Compliant Newhaven Display International Page 3 of 18 NHD-320240-WG-Bx F T I-VZ# 2.Precautions in Use of LCD Module (1)Avoid applying excessive shock to the module or making any alterations or modifications to it. (2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of LCD Module. (3)Don’t disassemble the LCM. (4)Don’t operate it above the absolute maximum rating. (5)Don’t drop, bend or twist LCM. (6)Soldering: only to the I/O terminals. (7)Storage: please store in anti-static electricity container and clean environment. 3.General Specification NHD-320240WG-BxFTI-VZ# ITEM STANDARD VALUE UNIT Number of dots 320x240 dots Outline dimension 160.0(W)x 109.0(H)x 13.0max(T) mm View area 122.0(W)x 92.0(H) mm Active area 115.18(W)x 86.38(H) mm Dot size 0.34(W)x 0.34(H) mm Dot pitch 0.36(W)x 0.36(H) mm LCD type FSTN (-), Transmissive View direction 6 o’clock Backlight CCFL, White Newhaven Display International Page 4 of 18 NHD-320240-WG-Bx F T I-VZ# 4.Absolute Maximum Ratings ITEM SYMBOL MIN. TYP. MAX. UNIT Operating Temperature TOP -20 ᧩ +70 ഒ Storage Temperature TST -30 ᧩ +80 ഒ Input Voltage VI 0 ᧩ VDD V Supply Voltage For Logic VDD 0 ᧩ 6.5 V Supply Voltage For LCD VDD-VEE 0 ᧩ 32 V 5.Electrical Characteristics ITEM Logic Voltage Supply Voltage For LCD SYMBOL CONDITION MIN. TYP. MAX. UNIT VDD-VSS ᧩ 4.75 5.0 5.25 V Ta=-20ഒ ᧩ ᧩ 26.1 V Ta=25ഒ ᧩ 23.8 ᧩ V Ta=+70ഒ 22.2 ᧩ ᧩ V VDD-VO Input High Volt. VIH ᧩ 0.5VDD ᧩ VDD V Input Low Volt. VIL ᧩ 0 ᧩ 0.2VDD V Output High Volt. VOH ᧩ VDD -0.4 ᧩ ᧩ V Output Low Volt. VOL ᧩ ᧩ ᧩ 0.4 V Supply Current IDD ᧩ 65.0 75.0 85.0 mA 6.Optical Characteristics ITEM SYMBAL CONDITION MIN TYP MAX UNIT (V)˥ CRฺ2 20 ᧩ 40 deg. (H)˳ CRฺ2 -30 ᧩ 30 deg. CR ᧩ ᧩ 3 ᧩ ᧩ View Angle Contrast Ratio Newhaven Display International. Page 5 of 18 NHD-320240-WG - B x F T I - V Z # ITEM SYMBAL CONDITION MIN TYP MAX UNIT (V)Ӱ CRЊ2 20 Ё 40 deg. (H)ӽ CRЊ2 -30 Ё 30 deg. CR Ё Ё 3 Ё Ё T rise Ё Ё 200 300 ms T fall Ё Ё 150 200 ms View Angle Contrast Ratio Response Time 6.1ʳ Definitions ϮView Anglesʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ϮContrast Ratio ( Visual angle direction ) Brightness at selected state ( BS ) Brightness at non-selected state ( Bns ) Selected state X Brightness (%) CR = ӽ Z Non-selected state Bs Bns ӰY Operating voltage for LCD driving ʳ ϮResponse time Selected Condition Nonselected Condition 90 % 100 % Brightness Nonselected Condition 10 % tr td Rise Time Newhaven Display International Decay Time ( fall time tf ) Page 6 of 17 NHD-320240-WG-BxFTI-VZ# 7.Interface Description Pin No. Symbol Level Description 1 VSS 0V 2 VDD 5.0V 3 VO 4 A0 H/L RD=L WR=H ,A0=L :Data Read AO=H :Status read RD=H WR=L ,A0=L :Data Write AO=H :Command write 5 WR H/L 8080 family: Write signal, 6800 family: R/W signal 6 RD H/L 8080 family: Read signal, 6800 family: Enable clock 7~14 DB0~DB7 H/L Data bus line 15 CS H/L Chip select ,Active L 16 RES H/L Controller reset signal, Active L 17 Vee Negative Voltage Output 18 NC NC 19 NC NC 20 WAIT Ground Power supply for Logic (Variable) Driving voltage for LCD Newhaven Display International. Check Busy Page 7 of 18 NHD-320240-WG- B x F T I - V Z # 8.Contour Drawing & Block diagram 165 0.5 152.0 141.0 122.0(VA) 115.18(AA) 11.0 25.0 28.41 109.0 0.5 101.0 104.7 92.0(VA) 86.38(AA) 4.0 2.15 8.5 11.31 4.0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 11.0MAX 6.5 1.0 ZIF CONNECTOR COMPARE MOLEX-52207-2090 1 CON2 20 190 5 41.0 320*240 Dots 4- 3.5 LED B/L 47.4 160.0 CCFL B/L 0.5 Vss Vdd Vo A0 WR RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 CS RES Vee NC NC WAIT 0.36 0.34 0.36 0.34 DOT SIZE SCALE 10/1 LED B/L drive directly fromA,K. Vee External contrast adjustment. FGND Power ON Reset Bias and Power Circuit N.V. Generator Driver -25V Com161~240 VR 10K~20K Vdd Vo Driver MPU Com81~160 Controller Com1~80 SED13700 CL1 M FLM Driver RD WR A0 DB0~DB7 CS RES SEL1 * R 320X240 DOT A K B/L LCM Seg1~80 Seg81~160 Seg161~240 Seg241~320 Driver Driver Driver Driver CL2 DB0~DB3 Frame PAD *:6800 family or 8080family interface selectable. Newhaven Display International. Page 8 of 18 NHD-320240-WG- B x F T I - V Z # 9.Timing Characteristics For relative timing diagram please see the spec of S1D13700. 9.1 Differences Between SED1335 and S1D13700 1᧪ S1D13700 almost can replace SED1335᧨and it can drive 240*160 dots in 16 gray level, or 320*240 dots in 4 gray level. 2᧪ There are 2 Main differences and being described as below: (1)᧪The Check Busy method of SED1335 is reading the D6 of STATUS resister. Please The Check Busy method of S1D13700 is checking the “WAIT” pin directly.ᇭ Newhaven Display International Page 9 of 18 NHD-320240-WG-BxFTI-VZ# (2) Owing to S1D13700 having 32K*8 SRAM inside, so It doesn’t need to set the bit “M1” in “SYSTEM SET”. For S1D13700, we doesn’t set M1 (bit1)᧨the setting for SED 1335 is shown as below: The setting of S1D13700 will show as follow: Newhaven Display International Page 10 of 18 NHD-320240-WG B x F T I - V Z # 10.RELIABILITY Content of Reliability Test (wide temperature, -20ഒ~70ഒ) Environmental Test Test Item Content of Test Test Condition Endurance test applying the high storage temperature for a 80ഒ long time. 200hrs Low Temperature Endurance test applying the high storage temperature for a -30ഒ storage long time. 200hrs High Temperature Endurance test applying the electric stress (Voltage & 70ഒ Operation Current) and the thermal stress to the element for a long time. 200hrs Low Temperature Endurance test applying the electric stress under low -20ഒ Operation temperature for a long time. 200hrs High Temperature storage Note 2 1,2 —— 1 The module should be allowed to stand at 60ഒ,90%RH max 60ഒ,90%RH High Temperature/ For 96hrs under no-load condition excluding the polarizer, 1,2 Humidity Operation 96hrs Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of operation -20ഒ 25ഒ 70ഒ -20ഒ/70ഒ Thermal shock resistance —— 10 cycles 30min 5min 30min 1 cycle Total fixed amplitude : 15mm Endurance test applying the vibration during transportation Vibration Frequency : Vibration test 3 and using. 10~55Hz One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes VS=800V,RS=1.5k˖ Static electricity test Endurance test applying the electric stress to the terminal. CS=100pF —— 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container. Newhaven Display International Page 11 of 18 NHD-320240- B x F T I - V Z # 16 11. Backlight Information ʳ CCFL backlight Specification Item Symbol (AT=25к) Specification Min Typ Max Unit Condition Luminance Frequency FL 40 50 60 KHZ Ё Tube current IL 3.5 5.0 6.5 mArms Ё Output Open Voltage VOpen 1100 Ё Ё Vrms No load voltage Tube Voltage VLoadS Ё 335 Ё Vrms Ё Brightness B 2500 Ё Ё Cd/m2 IFL =5.0mArms Brightness Uniformity Bu 75% Ё Ё % IFL =5.0mArms Life time Ё 50,000 Ё Ё hrs CCFL Connector: XHP-3 (JST) Newhaven Display International Page 16 of 16 12.Inspection NO 01 02 specification Item Criterion AQL Electrical Testing 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character, dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 LCD viewing angle defect. 1.7 Mixed product types. 1.8 Contrast defect. 0.65 Black or white spots on 2.1 White and black spots on display ู0.25mm, no more than LCD three white or black spots present. (display 2.2 Densely spaced: No more than two spots or lines within 3mm only) 3.1 Round type : As following drawing ˓ [\ 6,=( $FFHSWDEOH4 2.5 7< ˓ู 03 04 $FFHSWQR GHQVH LCD black spots, white ᧸˓ู spots, ᧸˓ู contaminati on ᧸˓ (non-display 3.2 Line type : (As following drawing) ) Length Width Acceptable Q TY --Accept no dense Wู Polarizer bubbles Newhaven Display International. Lู 0.02᧸Wู Lู --- 0.03᧸Wู If bubbles are visible, judge using black spot specifications, not easy to find, must check in specify direction. Page 13 of 18 0.05᧸W Size ˓ ˓ู 2.5 2.5 2 As round type Acceptable Q TY Accept no dense ᧸˓ู 3 ᧸˓ู 2 ᧸˓ Total Q TY 0 2.5 3 NHD-320240-WG-Bx F T I-VZ# NO Item 05 Scratches Criterion AQL Follow NO.3 LCD black spots, white spots, contamination Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length: 6.1 General glass chip : 6.1.1 Chip on panel surface and crack between panels: Chipped 06 glass ]&KLSWKLFNQHVV \&KLSZLGWK [&KLSOHQJWK =ูW 1RWRYHUYLHZLQJ [ูD 2.5 DUHD W᧸]ูW 1RWH[FHHGN [ูD ც,IWKHUHDUHRUPRUHFKLSV[LVWRWDOOHQJWKRIHDFKFKLS &RUQHUFUDFN Newhaven Display International ]&KLSWKLFNQHVV \&KLSZLGWK [&KLSOHQJWK =ูW 1RWRYHUYLHZLQJ [ูD Page 14 of 18 NHD-320240-WG- B x F T I - V Z # DUHD W᧸]ูW 1RWH[FHHGN [ูD ც,IWKHUHDUHRUPRUHFKLSV[LVWKHWRWDOOHQJWKRIHDFKFKLS Newhaven Display International Page 15 of 18 NHD-320240-WG- B x F T I - V Z # NO Item Criterion AQL 6\PEROV x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : \&KLSZLGWK [&KLSOHQJWK ]&KLSWKLFNQHVV \ูPP [ูD ᧸ ]ูW 1RQFRQGXFWLYHSRUWLRQ 06 Glass cra ck 2.5 \&KLSZLGWK [&KLSOHQJWK ]&KLS WKLFNQHVV \ู/ [ูD ᧸ ]ูW ც,IWKHFKLSSHGDUHDWRXFKHVWKH,72WHUPLQDORYHURIWKH ,72PXVWUHPDLQDQGEHLQVSHFWHGDFFRUGLQJWRHOHFWURGH WHUPLQDOVSHFLILFDWLRQV ც,IWKHSURGXFWZLOOEHKHDWVHDOHGE\WKHFXVWRPHUWKH DOLJQPHQWPDUNQRWEHGDPDJHG 6XEVWUDWHSURWXEHUDQFHDQGLQWHUQDOFUDFN \ZLGWK [OHQJWK \ู/ [ูD NO Item Newhaven Display International Criterion Page 16 of 18 AQL NHD-320240-WG- B x F T I - V Z # 07 Cracked glass 7KH/&'ZLWKH[WHQVLYHFUDFNLVQRWDFFHSWDEOH 2.5 ,OOXPLQDWLRQVRXUFHIOLFNHUVZKHQOLW 08 Backlight elements 6SRWVRUVFUDWFKHGWKDWDSSHDUZKHQOLWPXVWEHMXGJHG 8VLQJ/&'VSRWOLQHVDQGFRQWDPLQDWLRQVWDQGDUGV %DFNOLJKWGRHVQಬWOLJKWRUFRORUZURQJ 0.65 2.5 0.65 09 Bezel %H]HOPD\QRWKDYHUXVWEHGHIRUPHGRUKDYH ILQJHUSULQWVVWDLQVRURWKHUFRQWDPLQDWLRQ 2.5 0.65 %H]HOPXVWFRPSO\ZLWKMREVSHFLILFDWLRQV &2%VHDOPD\QRWKDYHSLQKROHVODUJHUWKDQPPRU 2.5 2.5 0.65 FRQWDPLQDWLRQ &2%VHDOVXUIDFHPD\QRWKDYHSLQKROHVWKURXJKWRWKH 2.5 ,& 10 PCBᇬCOB The height of the COB should not exceed the height indicated in the assembly diagram. 10.4 There may not be more than 2mm of sealant outside the seal area on the PCB. And there should be no more than three places. 10.5 No oxidation or contamination PCB terminals. 10.6 Parts on PCB must be the same as on the production characteristic chart. There should be no wrong parts, missing parts or excess parts. 10.7 The jumper on the PCB should conform to the product characteristic chart. 10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw hold pad, make sure it is smoothed down. 10.9 The Scraping testing standard for Copper Coating of PCB 2.5 0.65 0.65 2.5 2.5 X Y 11 Soldering X * Y<=2mm2 1RXQPHOWHGVROGHUSDVWHPD\EHSUHVHQWRQWKH3&% 2.5 2.5 1RFROGVROGHUMRLQWVPLVVLQJVROGHUFRQQHFWLRQV 2.5 R[LGDWLRQRULFLFOH 0.65 1RUHVLGXHRUVROGHUEDOOVRQ3&% 1RVKRUWFLUFXLWVLQFRPSRQHQWVRQ3&% Newhaven Display International Page 17 of 18 NHD-320240-WG- B x F T I - V Z # NO Item Criterion AQL 1RR[LGDWLRQFRQWDPLQDWLRQFXUYHVRUEHQGVRQ 2.5 LQWHUIDFH3LQ2/%RI7&3 1RFUDFNVRQLQWHUIDFHSLQ2/%RI7&3 0.65 1RFRQWDPLQDWLRQVROGHUUHVLGXHRUVROGHUEDOOVRQ 2.5 SURGXFW 2.5 7KH,&RQWKH7&3PD\QRWEHGDPDJHGFLUFXLWV 2.5 7KHXSSHUPRVWHGJHRIWKHSURWHFWLYHVWULSRQWKH LQWHUIDFHSLQPXVWEHSUHVHQWRUORRNDVLILWFDXVHWKH LQWHUIDFHSLQWRVHYHU General 12 2.5 7KHUHVLGXDOURVLQRUWLQRLORIVROGHULQJFRPSRQHQWRU appearance FKLSFRPSRQHQWLVQRWEXUQHGLQWREURZQRUEODFN 2.5 FRORU 0.65 6HDODQWRQWRSRIWKH,72FLUFXLWKDVQRWKDUGHQHG 0.65 3LQW\SHPXVWPDWFKW\SHLQVSHFLILFDWLRQVKHHW 0.65 /&'SLQORRVHRUPLVVLQJSLQV 3URGXFWSDFNDJLQJPXVWWKHVDPHDVVSHFLILHGRQ 0.65 SDFNDJLQJVSHFLILFDWLRQVKHHW 3URGXFWGLPHQVLRQDQGVWUXFWXUHPXVWFRQIRUPWR SURGXFWVSHFLILFDWLRQVKHHW Newhaven Display International Page 18 of 18 NHD-320240-WG- B x F T I - V Z #