User’s Guide
NHD-5.7-320240WFB-ETXI#-T
LCM
(Liquid Crystal Display Module)
RoHS Compliant
For product support, contact
Newhaven Display International
2511 Technology Drive, #101
Elgin, IL 60124
Tel: (847) 844-8795 Fax: (847) 844-8796
November 10, 2008
RECORDS OF REVISION
VERSION
DATE
0
A
2008.04.01
2008.05.27
DOC. FIRST ISSUE
REVISED
PAGE NO. SUMMARY
8
First issue
Modify pin2 and pin8
Contents
1. Module Classification Information
2. Block Diagram
3. Electrical Characteristics
4. Absolute Maximum Ratings
5. Interface Pin Function
6. Timing Characteristics
7. Optical Characteristics
8. Contour Drawing
9. LED driving conditions
10. Inspection specification
11. software (Register Initiate code)
ร 3 Δ٥ 22
1.Module Classification Information
NHD
5.7-320240 WFB - E T X I
c
d
e
f
#T
ghi
j
c Brand᧶NEWHAVEN DISPLAY INTERNATIONAL
d Display Size: 5.7inch diagonal, 320xRGBx240 pixels
e Display Type᧶WFB: TFT
f Model serials number: E : with Epson Controller
g Backlight Type᧶ NൺWithout backlight
h LCD Mode᧶
i LCD Polarizer
Type/
Temperature
range/ View
direction
AൺLED, Amber
BൺEL, Blue green
RൺLED, Red
DൺEL, Green
OൺLED, Orange
WൺEL, White
GൺLED, Green
FൺCCFL, White
TൺLED, White
YൺLED, Yellow Green
SൺLED, Bright White
BൺTN Positive, Gray
TൺFSTN Negative
NൺTN Negative,
MൺSTN Negative, Blue
GൺSTN Positive, Gray
FൺFSTN Positive
YൺSTN Positive, Yellow Green
X: TFT, normally white
AൺReflective, N.T, 6:00
HൺTransflective, W.T,6:00
DൺReflective, N.T, 12:00
KൺTransflective,W.T,12:00
GൺReflective, W. T, 6:00
CൺTransmissive, N.T,6:00
JൺReflective, W. T, 12:00
FൺTransmissive, N.T,12:00
BൺTransflective, N.T,6:00
IൺTransmissive, W. T, 6:00
EൺTransflective, N.T.12:00
LൺTransmissive, W.T,12:00
j Special Code
# : RoHS Compliant
T: With Touch Panel
Newhaven Display International
Page 4 of 22
NHD -5.7-320240WFB-ETXI#-T
This product is composed of a TFT LCD panel, driver ICs,
FPC, Control Board and a backlight unit.
Item
Dimension
Unit
320 x RGBx240(TFT)
dots
149.0x 109.0 x 11.5 (max)
mm
View area
115.200x 86.40
mm
Dot pitch
0.12 x 0.36
mm
Dot Matrix
Module dimension
Driving IC package
COG
LCD type
TFT, Negative, Transmissive
View direction
6 o’clock
Backlight Type
LED,Normally White
Controller IC
SID13A04 - 16 bit mode only
*Expose the IC number blaze (Luminosity over than 1 cd) when using the LCM may cause IC operating
failure.
*Color tone slight changed by temperature and driving voltage.
ร 5 Δ٥ 22
2.Block Diagram
TFT ARRAY/CELL
320(R/G/B) X 240
6 bits data
for R/G/B
CLK Hs Vs
S1D13A04
Power
Circuit
BackLight
Vcom
VGL
Circuit
VGH
VCC(3.3V)
GND
Address Bus Data Bus
17 bit
16bit
Contral
signal
Bit0 ~ Bit4
RED
Bit5 ~ Bit10 GREEN
Bit11~ Bit15 BLUE
ร 6 Δ٥ 22
3.Electrical Characteristics
Item
Symbol
Condition
Min
Typ
Max
Unit
VCC
Ё
3.0
3.3
3.6
V
Input High Volt.
VIH
Ё
0.7 VCC
Ё
VCC
V
Input Low Volt.
VIL
Ё
0
Ё
0.3Vcc
V
Supply Voltage For Logic
VGH *1
LCD Driving Supply
Voltage
Supply Current
V
15
Ta=25к
VGL*2
*3
-10
V
VcomH
2.5
5.5
VcomL
-2.0
0
IVDD
VDD=3.3V
Ё
5
8
mA
4.Absolute Maximum Ratings
Item
Symbol
Min
Typ
Max
Unit
Operating Temperature
TOP
-20
Ё
+70
к
Storage Temperature
TST
-30
Ё
+80
к
VGH
-0.3
Ё
18
V
VGL
-15
Ё
0.3
V
VCC
-0.3
Ё
6.0
V
Power Supply Voltage
ร 7 Δ٥ 22
5.Interface Pin Function
5-1
Pins Connection To Control Board
ˣ˂ˡʳ ˦̌̀˵̂˿ʳ
˙̈́˶̇˼̂́ʳ
˄ʳ ˩˶˶ʳ
ˣ̂̊˸̅ʳ˦̈̃̃˿̌ʳˍʳʾˆˁˆ˩ʳ
˅ʳ ˩˶˶ʳ
ˣ̂̊˸̅ʳ˦̈̃̃˿̌ʳˍʳʾˆˁˆ˩ʳ
ˆʳ
ˇʳ
ˈʳ
ˉʳ
ˊʳ
ˋʳ
ˌʳ
˄˃ʳ
˄˄ʳ
˄˅ʳ
˄ˆʳ
˄ˇʳ
˄ˈʳ
˄ˉʳ
˄ˊʳ
˄ˋʳ
˄ˌʳ
˅˃ʳ
˅˄ʳ
˅˅ʳ
˅ˆʳ
˗˕˃ʳ
˗˕˄ʳ
˗˕˅ʳ
˗˕ˆʳ
˗˕ˇʳ
˗˕ˈʳ
˗˕ˉʳ
˗˕ˊʳ
˗˕ˋʳ
˗˕ˌʳ
˗˕˄˃ʳ
˗˕˄˄ʳ
˗˕˄˅ʳ
˗˕˄ˆʳ
˗˕˄ˇʳ
˗˕˄ˈʳ
˖˦ʳ
ˠ˥ʳ
˥˗ʳ
˪˥ʳ
˕˛˘ʳ
ʳ
˅ˇʳ ˥˘˦˧ʳ
˅ˈʳ ˪˔˜˧ʳ
ˣ˂ˡʳ ˦̌̀˵̂˿
˙̈́˶̇˼̂́ʳ
˅ˉʳ VCC
ˣ̂̊˸̅ʳ˦̈̃̃˿̌ʳˍʳʾˆˁˆ˩ʳ
Typically used as input clock
˅ˊʳ ˖˟˞ʳ
source for pixel clock .
Normally this pin can be floated
˅ˋʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
˅ˌʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
ˆ˃ʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
ˆ˄ʳ ˔˗˄ʳ
˦̌̆̇˸̀ʳ˴˷˷̅˸̆̆ʳ˵̈̆ʳ˵˼̇̆ʳ
ˆ˅ʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
ˆˆʳ ˔˗˅ʳ
˦̌̆̇˸̀ʳ˴˷˷̅˸̆̆ʳ˵̈̆ʳ˵˼̇̆ʳ
ˆˇʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
˦̌̆̇˸̀ʳ˴˷˷̅˸̆̆ʳ˵̈̆ʳ˵˼̇̆ʳ
˜́̃̈̇ʳ ˷˴̇˴ʳ ˹̅̂̀ʳ ̇˻˸ʳ ̆̌̆̇˸̀ʳ ˷˴̇˴ʳ ˆˈʳ ˔˗ˆʳ
˵̈̆ˁʳ
ˆˉʳ ˚ˡ˗ʳ ˚̅̂̈́˷ʳ˹̂̅ʳ˿̂˺˼˶ʳ˶˼̅˶̈˼̇ʳ
ˆˊʳ ˔˗ˇʳ
ˆˋʳ ˔˗ˈʳ
ˆˌʳ ˔˗ˉʳ
ˇ˃ʳ ˔˗ˊʳ
ˇ˄ʳ ˔˗ˋʳ
ˇ˅ʳ ˔˗ˌʳ
ˇˆʳ ˔˗˄˃ʳ
˖˻˼̃ʳ̆˸˿˸˶̇ʳ˼́̃̈̇ˁʳ
ˇˇʳ ˔˗˄˄ʳ
˦˸˸ʳˡ̂̇˸ʻ˄ʼʳ
ˇˈʳ ˔˗˄˅ʳ ˦̌̆̇˸̀ʳ˴˷˷̅˸̆̆ʳ˵̈̆ʳ˵˼̇̆ʳ
̇˻˼̆ʳ̃˼́ʳ˼́̃̈̇̆ʳ̇˻˸ʳ̅˸˴˷ʳ˶̂̀̀˴́˷
ˇˉʳ ˔˗˄ˆʳ
̊̅˼̇˸ʳ˸́˴˵˿˸ʳ̆˼˺́˴˿ʳ
ˇˊʳ ˔˗˄ˇʳ
˧˻˼̆ʳ̃˼́ʳ˼́̃̈̇̆ʳ̇˻˸ʳ˵̌̇˸ʳ˸́˴˵˿˸ʳ
ˇˋʳ ˔˗˄ˈʳ
̆˼˺́˴˿ʳ˹̂̅ʳ̇˻˸ʳ˻˼˺˻ʳ˷˴̇˴ʳ˵̌̇˸ʳ ʳ
ʽˡ̂̇˸ʳʻ˅ʼʳ
˔˶̇˼̉˸ʳ˿̂̊ʳ˼́̃̈̇ʳ̇̂ʳ̆˸̇ʳ˴˿˿ʳ˼́̇˸̅́˴˿ʳ ˇˌʳ ˔˗˄ˉʳ
̅˸˺˼̆̇˸̅̆ʳ̇̂ʳ̇˻˸ʳ˷˸˹˴̈˿̇ʳ̆̇˴̇˸ʳ
˧˻˼̆ʳ̃˼́ʳ̂̈̇̃̈̇̆ʳ̇˻˸ʳ̊˴˼̇ʳ̆˼˺́˴˿ʳ
ˈ˃ʳ ˔˗˄ˊʳ
ˡ̂̇˸ʻ˄ʼˍ ŎİœĤġŪŴġŴŦŵġũŪŨũġŵŰġŢŤŤŦŴŴġťŪŴűŭŢźġţŶŧŧŦųĭġŭŰŸġŵŰġŢŤŤŦŴŴġŵũŦġųŦŨŪŴŵŦųŴį
ġ
ŏŰŵŦĩijĪĻġġŃʼnņġŴũŰŶŭťġţŦġŴŦŵġũŪŨũĭġŵũŪŴġťŪŴűŭŢźġŴŶűűŰųŵŴġōŪŵŵŭŦġņůťŪŢůġIJķĮţŪŵġŮŰťŦġŰůŭźįʳ
ร 8 Δ٥ 22
6.Timing Characteristics
7.2/Joufsgbdf!Ujnjoh!
ร 9 Δ٥ 22
7.Optical Characteristics
ร 10 Δ٥ 22
7.1 Definition of optical characteristics
ร 11 Δ٥ 22
ร 12 Δ٥ 22
8.Contour Drawing
149.0±0.5
152.0±0.2
4.0
37.3
138.7±0.5
118.28±0.2(VA)(Frame)
4-1 PTH
(320*3)*240 Dots
94.4
7.3
86.40±0.2(AA)
115.20±0.2(AA)
15.3
44.4
6.2
101.0±0.2
88.6±0.2(VA)(Frame)
6.3
CON2
Vcc
Vcc
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DB8
DB9
DB10
DB11
DB12
DB13
DB14
18 DB15
CS
19
20 MR
21
RD
22 WR
23 BHE
24 REST
25 WAIT
26 VCC
27 CLK
28 GND
29 GND
30 GND
31 AD1
32 GND
33 AD2
34 GND
AD3
GND
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD16
AD17
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
200.0±10.0
3
9.43
1
CON2
1.0
11.5Max
7.0±0.5
The non-specified tolerance of dimension is
0.36
0.12
DOT SIZE
SCALE 40/1
(38.9)
1
2
3
0.2mm.
A
NC
K
78.0(PCB)
(22.4)
55.7
1
50
50.0
CON1
70.0(PCB)
109.0±0.5
4.0
13.76
7.4
7.0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
CON2
ሿٙ૿
The non-specified tolerance of dimension is
ร 13 Δ٥ 22
0.2mm.
9. LED driving conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
LED Current
ILED
----
140
210
mA
LED voltage
VLED
9.0
----
10.5
V
-
(10,000)
----
----
-
IV
210.2
262.8
----
CD/M2
LED life Time
Luminous
Intensity
Note 1: There are 7 Groups LED shown as below, =9.9 V(Min)
Note 4: The luminous is measured through LCD panel.
ร 14 Δ٥ 22
Remark
Note1
Note 2,3
Note 4
10. Inspection specification
NO
01
02
03
04
Item
Criterion
AQL
Electrical
Testing
1.1 Missing vertical, horizontal segment, segment contrast defect.
1.2 Missing character , dot or icon.
1.3 Display malfunction.
1.4 No function or no display.
1.5 Current consumption exceeds product specifications.
1.6 LCD viewing angle defect.
1.7 Mixed product types.
1.8 Contrast defect.
0.65
Black or white 2.1 White and black spots on display Љ0.25mm, no more than
spots on LCD
three white or black spots present.
(display only) 2.2 Densely spaced: No more than two spots or lines within 3mm
2.5
3.1 Round type : As following drawing
ӥːʻʳ̋ʳʾʳ̌ʳʼʳ˂ʳ˅ʳ ʳ ʳ ʳ
˦˜˭˘ʳ
˔˶˶˸̃̇˴˵˿˸ʳˤʳ˧ˬ
ʳ ʳ ʳ ʳ ʳ ӥЉ˃ˁ˄˃ ˔˶˶˸̃̇ʳ́̂ʳ˷˸́̆˸
˃ˁ˄˃ІӥЉ˃ˁ˅˃
˅ʳ
˃ˁ˅˃ІӥЉ˃ˁ˅ˈ
˄ʳ
˃ˁ˅ˈІӥʳ
˃ʳ
ʳ
2.5
LCD black
spots, white
spots,
contamination
3.2 Line type : (As following drawing)
(non-display)
Length
Width
--WЉ˃ˁ˃˅
LЉˆˁ˃ 0.02ІWЉ˃ˁ˃ˆ
LЉ˅ˁˈ 0.03ІWЉ˃ˁ˃ˈʳ
--0.05ІW
Polarizer
bubbles
If bubbles are visible,
judge using black spot
specifications, not easy
to find, must check in
specify direction.
Size ӥ
ӥЉ˃ˁ˅˃
˃ˁ˅˃ІӥЉ˃ˁˈ˃
˃ˁˈ˃ІӥЉ˄ˁ˃˃
˄ˁ˃˃Іӥ
Total Q TY
ร 15 Δ٥ 22
Acceptable Q TY
Accept no dense
2.5
2
As round type
Acceptable Q TY
Accept no dense
3
2
0
3
2.5
NO
05
Item
Scratches
Criterion
Follow NO.3 LCD black spots, white spots, contamination
Symbols Define:
x: Chip length
y: Chip width
z: Chip thickness
k: Seal width
t: Glass thickness a: LCD side length
L: Electrode pad length:
AQL
6.1 General glass chip :
6.1.1 Chip on panel surface and crack between panels:
06
Chipped
glass
̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ
̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ
̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ
˭Љ˄˂˅̇ʳ
ˡ̂̇ʳ̂̉˸̅ʳ̉˼˸̊˼́˺ʳ˴̅˸˴
̋Љ˄˂ˋ˴ʳ
˄˂˅̇І̍Љ˅̇ʳ
ˡ̂̇ʳ˸̋˶˸˸˷ʳ˄˂ˆ˾ʳ ʳ
̋Љ˄˂ˋ˴ʳ
Ф˜˹ʳ̇˻˸̅˸ʳ˴̅˸ʳ˅ʳ̂̅ʳ̀̂̅˸ʳ˶˻˼̃̆ʿʳ̋ʳ˼̆ʳ̇̂̇˴˿ʳ˿˸́˺̇˻ʳ̂˹ʳ˸˴˶˻ʳ˶˻˼̃ˁʳ
ʳ
ˉˁ˄ˁ˅ʳ˖̂̅́˸̅ʳ˶̅˴˶˾ˍʳ
ʳ
ʳ
̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ
̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ
̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ
˭Љ˄˂˅̇ʳ
ˡ̂̇ʳ̂̉˸̅ʳ̉˼˸̊˼́˺ʳ˴̅˸˴
̋Љ˄˂ˋ˴ʳ
˄˂˅̇І̍Љ˅̇ʳ
ˡ̂̇ʳ˸̋˶˸˸˷ʳ˄˂ˆ˾ʳ ʳ
̋Љ˄˂ˋ˴ʳ
Ф˜˹ʳ̇˻˸̅˸ʳ˴̅˸ʳ˅ʳ̂̅ʳ̀̂̅˸ʳ˶˻˼̃̆ʿʳ̋ʳ˼̆ʳ̇˻˸ʳ̇̂̇˴˿ʳ˿˸́˺̇˻ʳ̂˹ʳ˸˴˶˻ʳ˶˻˼̃ˁʳ
ʳ
ร 16 Δ٥ 22
2.5
NO
Item
Criterion
AQL
˦̌̀˵̂˿̆ʳˍʳ
x: Chip length
y: Chip width
z: Chip thickness
k: Seal width
t: Glass thickness a: LCD side length
L: Electrode pad length
6.2 Protrusion over terminal :
6.2.1 Chip on electrode pad :
̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ʳ
̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ
̌Љ˃ˁˈ̀̀ʳ
̋Љ˄˂ˋ˴ʳ
ˉˁ˅ˁ˅ʳˡ̂́ˀ˶̂́˷̈˶̇˼̉˸ʳ̃̂̅̇˼̂́ˍʳ
06
̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ
˃ʳ Іʳ ̍ʳЉʳ̇ʳ
Glass
crack
2.5
̌ˍʳ˖˻˼̃ʳ̊˼˷̇˻ʳ ʳ
̋ˍʳ˖˻˼̃ʳ˿˸́˺̇˻ʳ
̍ˍʳ˖˻˼̃ʳ̇˻˼˶˾́˸̆̆ʳ
̌Љʳ˟ʳ
̋Љ˄˂ˋ˴ʳ
˃ʳ Іʳ ̍ʳЉʳ̇ʳ
Ф˜˹ʳ̇˻˸ʳ˶˻˼̃̃˸˷ʳ˴̅˸˴ʳ̇̂̈˶˻˸̆ʳ̇˻˸ʳ˜˧ˢʳ̇˸̅̀˼́˴˿ʿʳ̂̉˸̅ʳ˅˂ˆʳ̂˹ʳ̇˻˸ʳ˜˧ˢʳ̀̈̆̇ʳ
̅˸̀˴˼́ʳ˴́˷ʳ˵˸ʳ˼́̆̃˸˶̇˸˷ʳ˴˶˶̂̅˷˼́˺ʳ̇̂ʳ˸˿˸˶̇̅̂˷˸ʳ̇˸̅̀˼́˴˿ʳ̆̃˸˶˼˹˼˶˴̇˼̂́̆ˁʳ
Ф˜˹ʳ̇˻˸ʳ̃̅̂˷̈˶̇ʳ̊˼˿˿ʳ˵˸ʳ˻˸˴̇ʳ̆˸˴˿˸˷ʳ˵̌ʳ̇˻˸ʳ˶̈̆̇̂̀˸̅ʿʳ̇˻˸ʳ˴˿˼˺́̀˸́̇ʳ̀˴̅˾ʳ
́̂̇ʳ˵˸ʳ˷˴̀˴˺˸˷ˁʳ
ˉˁ˅ˁˆʳ˦̈˵̆̇̅˴̇˸ʳ̃̅̂̇̈˵˸̅˴́˶˸ʳ˴́˷ʳ˼́̇˸̅́˴˿ʳ˶̅˴˶˾ˁʳ
̌ˍʳ̊˼˷̇˻ʳ ʳ
̌Љ˄˂ˆ˟ʳ
ʳ
ʳ
ร 17 Δ٥ 22
̋ˍʳ˿˸́˺̇˻ʳ
̋ʳЉʳ˴ʳ
NO
Item
07
Cracked glass
08
09
10
11
Backlight
elements
Bezel
PCBΕCOB
Soldering
Criterion
˧˻˸ʳ˟˖˗ʳ̊˼̇˻ʳ˸̋̇˸́̆˼̉˸ʳ˶̅˴˶˾ʳ˼̆ʳ́̂̇ʳ˴˶˶˸̃̇˴˵˿˸ˁʳ
ʳ
ˋˁ˄ʳ˜˿˿̈̀˼́˴̇˼̂́ʳ̆̂̈̅˶˸ʳ˹˿˼˶˾˸̅̆ʳ̊˻˸́ʳ˿˼̇ˁʳ
ˋˁ˅ʳ˦̃̂̇̆ʳ̂̅ʳ̆˶̅˴̇˶˻˸˷ʳ̇˻˴̇ʳ˴̃̃˸˴̅ʳ̊˻˸́ʳ˿˼̇ʳ̀̈̆̇ʳ˵˸ʳ˽̈˷˺˸˷ˁʳ˨̆˼́˺ʳ
˟˖˗ʳ̆̃̂̇ʿʳ˿˼́˸̆ʳ˴́˷ʳ˶̂́̇˴̀˼́˴̇˼̂́ʳ̆̇˴́˷˴̅˷̆ˁʳ
ˋˁˆʳ˕˴˶˾˿˼˺˻̇ʳ˷̂˸̆́ϗ̇ʳ˿˼˺˻̇ʳ̂̅ʳ˶̂˿̂̅ʳ̊̅̂́˺ˁʳ
ʳ
ʳ
ˌˁ˄ʳ˕˸̍˸˿ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̅̈̆̇ʿʳ˵˸ʳ˷˸˹̂̅̀˸˷ʳ̂̅ʳ˻˴̉˸ʳ˹˼́˺˸̅̃̅˼́̇̆ʿʳ̆̇˴˼́̆ʳ
̂̅ʳ̂̇˻˸̅ʳ˶̂́̇˴̀˼́˴̇˼̂́ˁʳ
ˌˁ˅ʳ˕˸̍˸˿ʳ̀̈̆̇ʳ˶̂̀̃˿̌ʳ̊˼̇˻ʳ˽̂˵ʳ̆̃˸˶˼˹˼˶˴̇˼̂́̆ˁʳ
ʳ
ʳ
˄˃ˁ˄ʳ˖ˢ˕ʳ̆˸˴˿ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̃˼́˻̂˿˸̆ʳ˿˴̅˺˸̅ʳ̇˻˴́ʳ˃ˁ˅̀̀ʳ̂̅ʳ
˶̂́̇˴̀˼́˴̇˼̂́ˁʳ
˄˃ˁ˅ʳ˖ˢ˕ʳ̆˸˴˿ʳ̆̈̅˹˴˶˸ʳ̀˴̌ʳ́̂̇ʳ˻˴̉˸ʳ̃˼́˻̂˿˸̆ʳ̇˻̅̂̈˺˻ʳ̇̂ʳ̇˻˸ʳ˜˖ˁʳ
˄˃ˁˆʳThe height of the COB should not exceed the height indicated
in the assembly diagram.
10.4 There may not be more than 2mm of sealant outside the seal
area on the PCB. And there should be no more than three
places.
10.5 No oxidation or contamination PCB terminals.
10.6 Parts on PCB must be the same as on the production
characteristic chart. There should be no wrong parts, missing
parts or excess parts.
10.7 The jumper on the PCB should conform to the product
characteristic chart.
10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw
hold pad, make sure it is smoothed down.
ʳ
ʳ
˄˄ˁ˄ʳˡ̂ʳ̈́ˀ̀˸˿̇˸˷ʳ̆̂˿˷˸̅ʳ̃˴̆̇˸ʳ̀˴̌ʳ˵˸ʳ̃̅˸̆˸́̇ʳ̂́ʳ̇˻˸ʳˣ˖˕ˁʳ
˄˄ˁ˅ʳˡ̂ʳ˶̂˿˷ʳ̆̂˿˷˸̅ʳ˽̂˼́̇̆ʿʳ̀˼̆̆˼́˺ʳ̆̂˿˷˸̅ʳ˶̂́́˸˶̇˼̂́̆ʿʳ̂̋˼˷˴̇˼̂́ʳ̂̅ʳ
˼˶˼˶˿˸ˁʳ
˄˄ˁˆʳˡ̂ʳ̅˸̆˼˷̈˸ʳ̂̅ʳ̆̂˿˷˸̅ʳ˵˴˿˿̆ʳ̂́ʳˣ˖˕ˁʳ
˄˄ˁˇʳˡ̂ʳ̆˻̂̅̇ʳ˶˼̅˶̈˼̇̆ʳ˼́ʳ˶̂̀̃̂́˸́̇̆ʳ̂́ʳˣ˖˕ˁʳ
ʳ
ร 18 Δ٥ 22
AQL
2.5
0.65
2.5
0.65
2.5
0.65
2.5
2.5
0.65
2.5
2.5
0.65
0.65
2.5
2.5
2.5
2.5
0.65
NO
12
Item
General
appearance
Criterion
ʳ
˄˅ˁ˄ʳˡ̂ʳ̂̋˼˷˴̇˼̂́ʿʳ˶̂́̇˴̀˼́˴̇˼̂́ʿʳ˶̈̅̉˸̆ʳ̂̅ʿʳ˵˸́˷̆ʳ̂́ʳ˼́̇˸̅˹˴˶˸ʳˣ˼́ʳ
ʻˢ˟˕ʼʳ̂˹ʳ˧˖ˣˁʳ
˄˅ˁ˅ʳˡ̂ʳ˶̅˴˶˾̆ʳ̂́ʳ˼́̇˸̅˹˴˶˸ʳ̃˼́ʳʻˢ˟˕ʼʳ̂˹ʳ˧˖ˣˁʳ
˄˅ˁˆʳˡ̂ʳ˶̂́̇˴̀˼́˴̇˼̂́ʿʳ̆̂˿˷˸̅ʳ̅˸̆˼˷̈˸ʳ̂̅ʳ̆̂˿˷˸̅ʳ˵˴˿˿̆ʳ̂́ʳ̃̅̂˷̈˶̇ˁʳ
˄˅ˁˇʳ˧˻˸ʳ˜˖ʳ̂́ʳ̇˻˸ʳ˧˖ˣʳ̀˴̌ʳ́̂̇ʳ˵˸ʳ˷˴̀˴˺˸˷ʿʳ˶˼̅˶̈˼̇̆ˁʳ
˄˅ˁˈʳ˧˻˸ʳ̈̃̃˸̅̀̂̆̇ʳ˸˷˺˸ʳ̂˹ʳ̇˻˸ʳ̃̅̂̇˸˶̇˼̉˸ʳ̆̇̅˼̃ʳ̂́ʳ̇˻˸ʳ˼́̇˸̅˹˴˶˸ʳ̃˼́ʳ
̀̈̆̇ʳ˵˸ʳ̃̅˸̆˸́̇ʳ̂̅ʳ˿̂̂˾ʳ˴̆ʳ˼˹ʳ˼̇ʳ˶˴̈̆˸ʳ̇˻˸ʳ˼́̇˸̅˹˴˶˸ʳ̃˼́ʳ̇̂ʳ̆˸̉˸̅ˁʳ
˄˅ˁˉʳ˧˻˸ʳ̅˸̆˼˷̈˴˿ʳ̅̂̆˼́ʳ̂̅ʳ̇˼́ʳ̂˼˿ʳ̂˹ʳ̆̂˿˷˸̅˼́˺ʳʻ˶̂̀̃̂́˸́̇ʳ̂̅ʳ˶˻˼̃ʳ
˶̂̀̃̂́˸́̇ʼʳ˼̆ʳ́̂̇ʳ˵̈̅́˸˷ʳ˼́̇̂ʳ˵̅̂̊́ʳ̂̅ʳ˵˿˴˶˾ʳ˶̂˿̂̅ˁʳ
˄˅ˁˊʳ˦˸˴˿˴́̇ʳ̂́ʳ̇̂̃ʳ̂˹ʳ̇˻˸ʳ˜˧ˢʳ˶˼̅˶̈˼̇ʳ˻˴̆ʳ́̂̇ʳ˻˴̅˷˸́˸˷ˁʳ
˄˅ˁˋʳˣ˼́ʳ̇̌̃˸ʳ̀̈̆̇ʳ̀˴̇˶˻ʳ̇̌̃˸ʳ˼́ʳ̆̃˸˶˼˹˼˶˴̇˼̂́ʳ̆˻˸˸̇ˁʳ
˄˅ˁˌʳ˟˖˗ʳ̃˼́ʳ˿̂̂̆˸ʳ̂̅ʳ̀˼̆̆˼́˺ʳ̃˼́̆ˁʳ
˄˅ˁ˄˃ʳˣ̅̂˷̈˶̇ʳ̃˴˶˾˴˺˼́˺ʳ̀̈̆̇ʳ̇˻˸ʳ̆˴̀˸ʳ˴̆ʳ̆̃˸˶˼˹˼˸˷ʳ̂́ʳ̃˴˶˾˴˺˼́˺ʳ
̆̃˸˶˼˹˼˶˴̇˼̂́ʳ̆˻˸˸̇ˁʳ
˄˅ˁ˄˄ʳˣ̅̂˷̈˶̇ʳ˷˼̀˸́̆˼̂́ʳ˴́˷ʳ̆̇̅̈˶̇̈̅˸ʳ̀̈̆̇ʳ˶̂́˹̂̅̀ʳ̇̂ʳ̃̅̂˷̈˶̇ʳ
̆̃˸˶˼˹˼˶˴̇˼̂́ʳ̆˻˸˸̇ˁʳ
ʳ
ร 19 Δ٥ 22
AQL
2.5
0.65
2.5
2.5
2.5
2.5
2.5
0.65
0.65
0.65
0.65
11. software (Register Initiate code)
{ \
{ 0x14,
0x00000000 },
/* Power Save Configuration Register
*/ \
{ 0x64,
0x28D70000 },
/* GPIO Status and Control Register
*/ \
{ 0x04,
0x00000000 },
/* Memory Clock Configuration Register
*/ \
{ 0x08,
0x00000032 },
/* Pixel Clock Configuration Register
{ 0x0C,
0x00000061 },
/* Panel Type and MOD Rate Register
{ 0x10,
0x00000010 },
/* Display Settings Register
*/ \
{ 0x20,
0x00000030 },
/* Horizontal Total Register
*/ \
{ 0x24,
0x00000027 },
/* Horizontal Display Period Register
*/ \
{ 0x28,
0x0000000F },
/* Horizontal Display Period Start Position Register */
\
{ 0x2C,
0x00870156 },
/* FPLINE Register
{ 0x30,
0x00000103 },
/* Vertical Total Register
{ 0x34,
0x000000EF },
/* Vertical Display Period Register
{ 0x38,
0x00000013 },
/* Vertical Display Period Start Position Register
{ 0x3C,
0x00800000 },
/* FPFRAME Register
{ 0x40,
0x00000000 },
/* Main Window Display Start Address Register
{ 0x44,
0x000000A0 },
/* Main Window Line Address Offset Register
{ 0x50,
0x00000000 },
/* PIP+ Window Display Start Address Register
{ 0x54,
0x000000A0 },
/* PIP+ Window Line Address Offset Register
{ 0x58,
0x00000000 },
/* PIP+ Window X Positions Register
*/ \
{ 0x5C,
0x00000000 },
/* PIP+ Window Y Positions Register
*/ \
{ 0x60,
0x00000000 },
/* Special Purpose Register
*/ \
{ 0x70,
0x00000000 },
/* PWM Clock Configuration Register
{ 0x74,
0x00000000 },
/* PWMOUT Duty Cycle Register
{ 0x80,
0x00000000 },
/* Scratch Pad A Register
*/ \
{ 0x84,
0x00000000 },
/* Scratch Pad B Register
*/ \
{ 0x88,
0x00000000 },
/* Scratch Pad C Register
*/ \
{ S1D_REGDELAYON,
0x00000032 },
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
*/ \
/* LCD Panel Power On Delay (in ms)
*/ \
{ 0x64,
0x28D70001 },
/* GPIO Status and Control Register
*/ \
{ 0x14,
0x00000000 }
/* Power Save Configuration Register
*/ \
}
ร 20 Δ٥ 22
Newhaven LCM Sample Estimate Feedback Sheet
Module NumberΚ
Page: 1
1ΕPanel SpecificationΚ
1. Panel TypeΚ
ϭ Pass
ϭ NG ,
2. View DirectionΚ
ϭ Pass
ϭ NG ,
3. Numbers of DotsΚ
ϭ Pass
ϭ NG ,
4. View AreaΚ
ϭ Pass
ϭ NG ,
5. Active AreaΚ
ϭ Pass
ϭ NG ,
6. Operating TemperatureΚ
ϭ Pass
ϭ NG ,
7. Storage TemperatureΚ
ϭ Pass
ϭ NG ,
1. PCB SizeΚ
ϭ Pass
ϭ NG ,
2. Frame SizeΚ
ϭ Pass
ϭ NG ,
3. Material of FrameΚ
ϭ Pass
ϭ NG ,
4. Connector PositionΚ
ϭ Pass
ϭ NG ,
5. Fix Hole PositionΚ
ϭ Pass
ϭ NG ,
6. Backlight PositionΚ
ϭ Pass
ϭ NG ,
7. Thickness of PCBΚ
ϭ Pass
ϭ NG ,
8. Height of Frame to PCBΚ ϭ Pass
ϭ NG ,
9. Height of ModuleΚ
ϭ Pass
ϭ NG ,
10. OthersΚ
ϭ Pass
ϭ NG ,
1. Pitch of ConnectorΚ
ϭ Pass
ϭ NG ,
2. Hole size of ConnectorΚ
ϭ Pass
ϭ NG ,
3. Mounting Hole sizeΚ
ϭ Pass
ϭ NG ,
4. Mounting Hole TypeΚ
ϭ Pass
ϭ NG ,
5. OthersΚ
ϭ Pass
ϭ NG ,
1. B/L TypeΚ
ϭ Pass
ϭ NG ,
2. B/L ColorΚ
ϭ Pass
ϭ NG ,
8. OthersΚ
2ΕMechanical SpecificationΚ
3ΕRelative Hole SizeΚ
4ΕBacklight SpecificationΚ
3. B/L Driving Voltage (Reference for LED Type)Κ ϭ Pass
4. B/L Driving CurrentΚ
ϭ Pass
ϭ NG ,
5. Brightness of B/LΚ
ϭ Pass
ϭ NG ,
6. B/L Solder MethodΚ
ϭ Pass
ϭ NG ,
7. OthersΚ
ϭ Pass
ϭ NG ,
ЇЇ Go to page 2 ІІ
ร 21 Δ٥ 22
ϭ NG ,
Newhaven
Module NumberΚ
Page: 2
5ΕElectronic Characteristics of ModuleΚ
1. Input VoltageΚ
ϭ Pass
ϭ NG ,
2. Supply CurrentΚ
ϭ Pass
ϭ NG ,
3. Driving Voltage for LCDΚ
ϭ Pass
ϭ NG ,
4. Contrast for LCDΚ
ϭ Pass
ϭ NG ,
5. B/L Driving MethodΚ
ϭ Pass
ϭ NG ,
6. Negative Voltage OutputΚ
ϭ Pass
ϭ NG ,
7. Interface FunctionΚ
ϭ Pass
ϭ NG ,
8. LCD UniformityΚ
ϭ Pass
ϭ NG ,
9. ESD testΚ
ϭ Pass
ϭ NG ,
ϭ Pass
ϭ NG ,
10. OthersΚ
6ΕSummaryΚ
Sales signatureΚ
Customer SignatureΚ
DateΚ
ร 22 Δ٥ 22
/
/
User’s Guide
TS320240BRNO
Touch Panel
For product support, contact
Newhaven Display International
2511 Technology Drive, #101
Elgin, IL 60124
Tel: (847) 844-8795 Fax: (847) 844-8796
November 5, 2007
1
12. Touch panel Information:
TS-320240BRNO
2
ELECTRICAL SPECIFICATIONS:
ITEM
SPECIFICATION
TS-320240BRNO
CONDITION
350Ω ~ 1000Ω
DIRECTION: X
200Ω ~ 650Ω
DIRECTION: Y
INSULATION
MORE THAN
DC 25V
RESISTANCE
20MΩ
CHATTERING
LESS THAN
TIME
15 msec
ON RESISTANCE
100K PULL-UP
LINEARITY
±1.5%
X AXIS
±1.5%
Y AXIS
MACHINE SPECIFICATIONS
ITEM
OPERATING
SPECIFICATION
LESS THAN 80g
FORCE
CONDITION
R8.0 HS 40 °
SILICON RUBBER
OR R0.8
POLYACETAL PEN
SURFACE
MORE THAN 2H
PENCIL TEST
LIGHT
MORE THAN
@550nm
TRANSMISSION
80 %
HITACHI U3300
DURABILITY FOR
MORE THAN
FORCE: 250g
PEN SELECTIONS
1,200,000 TIMES
SPEED: 2cm/sec
HARDNESS