DC-DC Converter DIP-Package DMV-25 SERIES, 25WATT, 2:1 INPUT RANGE FEATURES: 2 year warranty Six-side shielded metal case Low ripple and noise Over current and short circuit protection Remote on/off Adjustable output voltage Model DMV25-1211 DMV25-1212 DMV25-1213 DMV25-1214 DMV25-1215 DMV25-1216 DMV25-1221 DMV25-1222 DMV25-1223 DMV25-1224 DMV25-1225 DMV25-2411 DMV25-2412 DMV25-2413 DMV25-2414 DMV25-2415 DMV25-2416 DMV25-2421 DMV25-2422 DMV25-2423 DMV25-2424 DMV25-2425 DMV25-4811 DMV25-4812 DMV25-4813 DMV25-4814 DMV25-4815 DMV25-4816 DMV25-4821 DMV25-4822 DMV25-4823 www.pairuigroup.com Input voltage (Vdc) 12(9~18) 24(18~36) 48(36~72) Output voltage (Vdc) Output current (A) Efficiency Typ. 3.3 5 82% 5 5 82% 9 2.77 87% 12 2.08 87% 15 1.66 87% 24 1.04 87% ±5 2.5 82% ±9 1.39 87% ±12 1.04 87% ±15 0.83 87% ±24 0.52 87% 3.3 5 82% 5 5 82% 9 2.77 87% 12 2.08 87% 15 1.66 87% 24 1.04 87% ±5 2.5 82% ±9 1.39 87% ±12 1.04 87% ±15 0.83 87% ±24 0.52 87% 3.3 5 82% 5 5 82% 9 2.77 87% 12 2.08 87% 15 1.66 87% 24 1.04 87% ±5 2.5 82% ±9 1.39 87% ±12 1.04 87% Page: 1/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-25 SERIES, 25WATT, 2:1 INPUT RANGE Model DMV25-4824 DMV25-4825 DMV25-11011 DMV25-11012 DMV25-11013 DMV25-11014 DMV25-11015 DMV25-11016 DMV25-11021 DMV25-11022 DMV25-11023 DMV25-11024 DMV25-11025 Input voltage (Vdc) Output voltage (Vdc) Output current (A) Efficiency Typ. ±15 0.83 87% ±24 0.52 87% 3.3 5 82% 5 5 82% 9 2.77 87% 12 2.08 87% 15 1.66 87% 24 1.04 87% ±5 2.5 82% ±9 1.39 87% ±12 1.04 87% ±15 0.83 87% ±24 0.52 87% 48(36~72) 110(72~144) Notes: 1. Other input and output models may available on request; 2. Above models are default to metal case. ELECTRICAL Input voltage range 12V 9-18Vdc 24V 18-36Vdc 48V 36-72Vdc 110V 72-144Vdc Remote control High level or vacant Turn on (Low level remote) Low level or connect ground Turn off Output voltage accuracy --- Vo1, Vo2: ±1%, ±3% Output voltage adjustable --- ±10% max. Line regulation Nominal Load, full voltage Load regulation 20% ~ 100% rated load Vo1, Vo2: ±0.5%, ±4% 5%-50%-75% load capability ∆Vo1/∆t: ±4.0%/500μs Dynamic response (transient/recovery time) Vo1, Vo2: ±0.2%, ±1.5% Vo≤5.0V, ≤50mVp-p Ripple and noise 20MHz BM, full load Vo≥48V, ≤180mVp-p Other, ≤100mVp-p Isolation voltage Input to output (<2mA/min) Input to case Switching frequency 300KHz Turn-on delay time --- Operating temperature range Free air www.pairuigroup.com 1500Vdc 500Vdc 330KHz max. ≤200ms -25℃ to +55℃ Page: 2/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-25 SERIES, 25WATT, 2:1 INPUT RANGE ELECTRICAL Storage temperature range Input under voltage protection -45℃ to +105℃ --When input voltage is lower than the Auto-recovery low input voltage Over current protection --- Auto-recovery Short circuit protection --- Continuous auto-recovery Cooling method --- Cooling by air convection Relative humidity --- 10%-90% max. Weight --- 61.8g MTBF Bellcore TR-332, 25℃ 2x105Hrs Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. ℃ MECHANICAL CONNECTION PIN # SINGLE DUAL 1 REM REM 2 -Vin -Vin 3 +Vin +Vin 4 No pin +Vo1 5 +Vo COM 6 GND -Vo2 7 TRIM TRIM Note: * Unit is mm(inch). LAYOUT www.pairuigroup.com Page: 3/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-25 SERIES, 25WATT, 2:1 INPUT RANGE ELECTRICAL CURVE NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE be helpful with over voltage protection and inrush limiting. Recommended FUSE better be 1.5~2times of the rated current . 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF. 3. C1,C2 for the input filter capacitor,0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 better within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 4/4 Date: 07/24/2015 *Subject to change without notice