DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE FEATURES: 1500Vac isolation voltage Six-side shielded metal case with low ripple and noise Over voltage, over current, short circuit protection Operating temperature range -40 3 year warranty Model DNV10-1211 DNV10-1212 DNV10-1213 DNV10-1214 DNV10-1215 ℃ to +85℃ Input voltage (Vdc) 12(9~18) DNV10-2411 DNV10-2412 DNV10-2413 DNV10-2414 DNV10-2415 DNV10-4811 DNV10-4812 DNV10-4813 DNV10-4814 DNV10-4815 DNV10-11012 DNV10-11013 DNV10-11014 DNV10-11015 24(18~36) 48(36~72) 110(66~160) Output voltage (Vdc) Output current (mA) Efficiency Typ. 3.3 3000 85% 5.1 2000 87% 12.1 800 87% 15.1 700 89% 24.2 400 89% 3.3 3000 87% 5.1 2000 88% 12.1 800 89% 15.1 700 90% 24.2 400 90% 3.3 3000 87% 5.1 2000 89% 12.1 800 89% 15.1 700 90% 24.2 400 90% 5.1 2000 89% 12.1 800 89% 15.1 700 90% 24.2 400 90% Notes: 1.Other input and output models may available on request; 2.You may request for the models with heatsink, plus “R” in the suffix, e.g. DNV10-1211R. ELECTRICAL Output voltage accuracy --- Line regulation Nominal Load, full voltage ±0.2% max. Load regulation 20% ~ 100% rated load ±0.5% max. Dynamic response (transient/recovery time) Ripple and noise www.pairuigroup.com ≤1% 5%-50%-75% load capability 20MHz BM, full load Page: 1 / 4 ∆Vo/∆t: ±5.0%/500μs 1% Vout max. Date: 07/30/2015 * Subject to change without notice DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE ELECTRICAL Isolation voltage (<2mA/min) Input to output 1500Vac Input to case 1000Vac Output to case 500Vac Isolation resistance 500Vdc 20MΩ Temperature coefficient --- ±0.02%/℃ max. Operating temperature range --- -40℃ to +85℃ Storage temperature range --- -45℃ to +120℃ Over current protection --- Auto-recovery Short circuit protection --- Continuous auto-recovery Over voltage protection --- Auto-recovery Relative humidity --- 10%-90% max. Conducted emission --- CLASS A MTBF Bellcore TR-332, 25℃ 200KHrs Weight --- 21g Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL WITHOUT HEATSINK www.pairuigroup.com WITH HEATSINK Page: 2 / 4 Date: 07/30/2015 * Subject to change without notice DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE MECHANICAL CONNECTION PCB LAYOUT PIN # SINGLE 1 +Vin 2 -Vin 3 +Vo 4 No Pin 5 GND Note: * Unit is mm(inch). TEMPERATURE PROFILE CAPACITIVE LOADS SELECTION Vout: 3.3V 5V Vout: 12V 5V Vout: 24V Recommended MAX. Recommended MAX. Recommended MAX. value value value value value value 10000μF 15000μF 1000μF 2200μF 470μF 1000μF www.pairuigroup.com Page: 3 / 4 Date: 07/30/2015 * Subject to change without notice DC-DC Converter DIP-Package DNV-10 SERIES, 10WATT, 2:1 INPUT RANGE NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE will be helpful with over voltage protection and inrush limiting. Recommended FUSE should better be 1.5~2times of the rated current ; 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF; 3. C1,C2 for the input filter capacitor, 0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 should within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 4 / 4 Date: 07/30/2015 * Subject to change without notice