DC-DC Converter DIP-Package DMV-30 SERIES, 30WATT, 2:1 INPUT RANGE FEATURES: 2 year warranty Six-side shielded metal case Low ripple and noise Over current and short circuit protection Remote on/off Adjustable output voltage Model DMV30-1215 DMV30-1211 DMV30-1216 DMV30-1212 DMV30-1213 DMV30-1214 DMV30-1221 DMV30-1223 DMV30-1222 DMV30-1224 DMV30-1225 DMV30-2411 DMV30-2416 DMV30-2412 DMV30-2413 DMV30-2414 DMV30-2421 DMV30-2423 DMV30-2422 DMV30-2424 DMV30-2425 DMV30-4811 DMV30-4816 DMV30-4812 DMV30-4813 DMV30-4814 DMV30-4821 DMV30-4823 DMV30-4822 DMV30-4824 DMV30-4825 www.pairuigroup.com Input voltage (Vdc) 12(9~18) 24(18~36) 48(36~72) Output voltage (Vdc) Output current (A) Efficiency Typ. 3.3 8 82% 5 6 82% 9 3.3 78% 12 2.5 87% 15 2 87% 24 1.25 87% ±5 3 82% ±9 1.65 78% ±12 1.25 87% ±15 1 78% ±24 0.625 78% 5 6 82% 9 3.3 78% 12 2.5 87% 15 2 87% 24 1.25 87% ±5 3 82% ±9 1.65 78% ±12 1.25 87% ±15 1 78% ±24 0.625 78% 5 6 82% 9 3.3 78% 12 2.5 87% 15 2 87% 24 1.25 87% ±5 3 82% ±9 1.65 78% ±12 1.25 87% ±15 1 78% ±24 0.625 78% Page: 1/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-30 SERIES, 30WATT, 2:1 INPUT RANGE Model DMV30-11011 DMV30-11016 DMV30-11012 DMV30-11013 DMV30-11014 DMV30-11021 DMV30-11023 DMV30-11022 DMV30-11024 DMV30-11025 Input voltage (Vdc) Output voltage (Vdc) Output current (A) Efficiency Typ. 5 6 82% 9 3.3 78% 12 2.5 87% 15 2 87% 24 1.25 87% ±5 3 82% ±9 1.65 78% ±12 1.25 87% ±15 1 78% ±24 0.625 78% 110(72~144) Notes: 1. Other input and output models may available on request; 2. Above models are default to metal case. ELECTRICAL Input voltage range 12V 9-18Vdc 24V 18-36Vdc 48V 36-72Vdc 110V 72-144Vdc Remote control High level or vacant Turn on (Low level remote) Low level or connect ground Turn off Output voltage accuracy --- Vo1, Vo2: ±1%, ±3% Output voltage adjustable --- ±10% max. Line regulation Nominal Load, full voltage Load regulation 20% ~ 100% rated load Vo1, Vo2: ±0.5%, ±4% 5%-50%-75% load capability ∆Vo1/∆t: ±4.0%/500μs Dynamic response (transient/recovery time) Vo1, Vo2: ±0.2%, ±1.5% Vo≤5.0V, ≤50mVp-p Ripple and noise 20MHz BM, full load Vo≥48V, ≤180mVp-p Other, ≤100mVp-p Isolation voltage Input to output (<2mA/min) Input to case Switching frequency 300KHz Turn-on delay time --- Operating temperature range Free air Storage temperature range --- Input under voltage protection www.pairuigroup.com 1500Vdc 500Vdc 330KHz max. ≤200ms -25℃ to +55℃ -45℃ to +105℃ When input voltage is lower than the low input voltage Page: 2/4 Auto-recovery Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-30 SERIES, 30WATT, 2:1 INPUT RANGE ELECTRICAL Over current protection --- Auto-recovery Short circuit protection --- Continuous auto-recovery Cooling method --- Cooling by air convection Relative humidity --- 10%-90% max. Weight --- 61.8g MTBF Bellcore TR-332, 25℃ 2x105Hrs Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. ℃ MECHANICAL CONNECTION PIN # SINGLE DUAL 1 REM REM 2 -Vin -Vin 3 +Vin +Vin 4 No pin +Vo1 5 +Vo COM 6 GND -Vo2 7 TRIM TRIM Note: * Unit is mm(inch). LAYOUT www.pairuigroup.com Page: 3/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-30 SERIES, 30WATT, 2:1 INPUT RANGE ELECTRICAL CURVE NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE be helpful with over voltage protection and inrush limiting. Recommended FUSE better be 1.5~2times of the rated current . 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF. 3. C1,C2 for the input filter capacitor,0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 better within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 4/4 Date: 07/24/2015 *Subject to change without notice