DC-DC Converter DIP-Package DMV-20W SERIES, 20WATT, 4:1 INPUT RANGE FEATURES: 2 year warranty Six-side shielded metal case Low ripple and noise Over current and short circuit protection Remote on/off Adjustable output voltage Model DMV20W-2411 DMV20W-2412 DMV20W-2413 DMV20W-2414 DMV20W-2415 DMV20W-2416 DMV20W-2421 DMV20W-2422 DMV20W-2423 DMV20W-2424 DMV20W-2425 DMV20W-4811 DMV20W-4812 DMV20W-4813 DMV20W-4814 DMV20W-4815 DMV20W-4816 DMV20W-4821 DMV20W-4822 DMV20W-4823 DMV20W-4824 DMV20W-4825 Input voltage (Vdc) 24(9~36) 48(18~72) Output voltage (Vdc) Output current (mA) Efficiency Typ. 5 4000 80% 9 2220 85% 12 1660 85% 15 1330 85% 24 830 85% 48 410 85% ±5 ±2000 80% ±9 ±1110 85% ±12 ±830 85% ±15 ±660 85% ±24 ±410 85% 5 4000 80% 9 2220 85% 12 1660 85% 15 1330 85% 24 830 85% 48 410 85% ±5 ±2000 80% ±9 ±1110 85% ±12 ±830 85% ±15 ±660 85% ±24 ±410 85% Notes: 1. Other input and output models may available on request; 2. Above models are default to metal case. www.pairuigroup.com Page: 1/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-20W SERIES, 20WATT, 4:1 INPUT RANGE ELECTRICAL Input voltage range 18V 9-36Vdc 36V 18-72Vdc Remote control High level or vacant Turn on (Low level remote) Low level or connect ground Turn off Output voltage accuracy --- Vo1, Vo2: ±1%, ±3% Output voltage adjustable --- ±10% Line regulation Nominal Load, full voltage Load regulation 20% ~ 100% rated load Vo1, Vo2: ±0.5%, ±4% 5%-50%-75% load capability ∆Vo1/∆t: ±4.0%/500μs Dynamic response (transient/recovery time) Vo1, Vo2: ±0.2%, ±1.5% Vo≤5.0V, ≤50mVp-p Ripple and noise 20MHz BM, full load Vo≥48V, ≤180mVp-p Other, ≤100mVp-p Isolation voltage Input to output (<2mA/min) Input to case Switching frequency 300KHz Turn-on delay time --- Operating temperature range Free air Storage temperature range --- Input under voltage protection 1500Vdc 500Vdc 330KHz max. ≤200ms -25℃ to +55℃ -45℃ to +105℃ When input voltage is lower than the low input voltage Auto-recovery Over current protection --- Auto-recovery Short circuit protection --- Continuous auto-recovery Cooling method --- Cooling by air convection Relative humidity --- 10%-90% max. Weight --- 35.7g MTBF Bellcore TR-332, 25℃ 2x105Hrs Notes: Unless otherwise specified, all the parameters of the test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. ℃ www.pairuigroup.com Page: 2/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-20W SERIES, 20WATT, 4:1 INPUT RANGE MECHANICAL CONNECTION PIN # SINGLE DUAL 1 REM REM 2 -Vin -Vin 3 +Vin +Vin 4 No pin +Vo1 5 +Vo COM 6 GND -Vo2 7 TRIM TRIM Note: * Unit is mm(inch). LAYOUT ELECTRICAL CURVE www.pairuigroup.com Page: 3/4 Date: 07/24/2015 *Subject to change without notice DC-DC Converter DIP-Package DMV-20W SERIES, 20WATT, 4:1 INPUT RANGE NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT 1. TVS&FUSE be helpful with over voltage protection and inrush limiting. Recommended FUSE better be 1.5~2times of the rated current . 2. The input filter capacitor C6 could select the aluminum electrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input voltage. Recommended capacitor should be between 22μF~100μF. 3. C1,C2 for the input filter capacitor,0.1~1μF high-frequency ceramics capacitor or chip capacitor are recommended. The withstand voltage of output filter C5, C7 should be greater than the highest output voltage. Recommended capacitor of C7 better within 100μF and C5 connected with the chip to reduce the input voltage peak, recommended 0.1~1μF high-frequency ceramics capacitor or chip capacitor. www.pairuigroup.com Page: 4/4 Date: 07/24/2015 *Subject to change without notice