PO54G74A, PO74G74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS www.potatosemi.com WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic FEATURES: DESCRIPTION: . Patented technology . Specified From –40°C to 125°C, –55°C to 125°C . Operating frequency is faster than 600MHz . VCC Operates from 1.65V to 3.6V . Propagation delay < 2ns max with 15pf load . Low input capacitance: 4pf typical . Latch-Up Performance Exceeds 250 mA Per JESD 17 . ESD Protection Exceeds JESD 22 . 5000-VHuman-BodyModel (A114-A) . 200-VMachineModel (A115-A) . Available in 14pin 150mil wide SOIC package . Available in 14pin Ceramic Dual Flatpack . Available in 20pin Leadless Ceramic Chip Carrier Potato Semiconductor’s PO74G74A is designed for world top performance using submicron CMOS technology to achieve higher than 600MHz TTL /CMOS output frequency with less than 2ns propagation delay. This dual D flip-flop is designed for 1.65-V to 3.6-V VCC operation. Inputs can be driven from either 3.3V or 5V devices. This feature allows the use of these devices as translators in a mixed 3.3V/5V system environment. 12 3 1CLK 11 4 1PRE 10 5 1Q 9 6 1Q 8 7 GND 1CLR NC VCC 1D 2CLR 1CLK NC 1PRE NC 1Q 2D 2CLK 2PRE 2Q 2Q CLR CLK D Q Q L H X X H L H L X X L H L L X X L L L L H X Q0 Q0 H H H H H L H 7 8 2 1 20 19 18 17 16 15 14 9 10 11 12 13 2D NC 2CLK NC 2PRE OUTPUTS PRE H 5 6 3 Logic Block Diagram Pin Description INPUTS 4 2Q 2Q 13 2 1D VCC 1Q GND NC 14 1 1CLR 2CLR Pin Configuration H 1CLR 1 1D 2 D PRE 1 L 1CLK 3 1PRE 4 1Q 5 1Q 14 Vcc 13 2CLR 12 2D 11 2CLK Q 10 2PRE Q 9 2Q 8 2Q Q Q CLR D PRE 2 6 CLR GND Potato Semiconductor Corporation 1 7 01/01/10 PO54G74A, PO74G74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS www.potatosemi.com WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic Maximum Ratings Description Max Unit Storage Temperature -65 to 150 °C Operation Temperature -55 to 125 °C Operation Voltage -0.5 to +4.6 V Input Voltage -0.5 to +5.5 V Output Voltage -0.5 to Vcc+0.5 V Note: stresses greater than listed under Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability specification is not implied. DC Electrical Characteristics Symbol Description VOH Output High voltage VOL Test Conditions Min Typ Max Unit Vcc=3V Vin=VIH or VIL, IOH= -12mA 2.4 3 - V Output Low voltage Vcc=3V Vin=VIH or VIL, IOH=12mA - 0.3 0.5 V VIH Input High voltage Guaranteed Logic HIGH Level (Input Pin) 2 - 5.5 V VIL Input Low voltage Guaranteed Logic LOW Level (Input Pin) -0.5 - 0.8 V IIH Input High current Vcc = 3.6V and Vin = 5.5V - - 1 uA IIL Input Low current Vcc = 3.6V and Vin = 0V - - -1 uA VIK Clamp diode voltage Vcc = Min. And IIN = -18mA - -0.7 -1.2 V Notes: 1. 2. 3. 4. 5. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. Typical values are at Vcc = 3.3V, 25 °C ambient. This parameter is guaranteed but not tested. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. VoH = Vcc – 0.6V at rated current Potato Semiconductor Corporation 2 01/01/10 PO54G74A, PO74G74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS www.potatosemi.com WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic Power Supply Characteristics Symbol IccQ Description Quiescent Power Supply Current Test Conditions (1) Min Typ Max Unit Vcc=Max, Vin=Vcc or GND - 0.1 40 uA Notes: 1. 2. 3. 4. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. Typical values are at Vcc = 3.3V, 25°C ambient. This parameter is guaranteed but not tested. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. Capacitance Parameters (1) Description Cin Cout Test Conditions Typ Input Capacitance Vin = 0V Output Capacitance Vout = 0V 4 6 Unit pF pF Notes: 1 This parameter is determined by device characterization but not production tested. Switching Characteristics Symbol Description Test Conditions (1) M ax - tsu th Setup time before CLK tPLH Propagation Delay CLK to Q or Q CL = 15pF 2 t PHL tPLH Propagation Delay CLK to Q or Q CL = 15pF 2 Propagation Delay CLR or PRE to Q or Q CL = 15pF 3 t PHL Propagation Delay CLR or PRE to Q or Q CL = 15pF 3 tr/tf Rise/Fall Time 0.8V – 2.0V 0.8 fmax Input Frequency CL=2pF - 15pF Hold time, data after CLK - Min Unit 0.5 ns 0.5 ns - ns ns 600 MHz ns ns ns Notes: 1. See test circuits and waveforms. 2. tPLH, tPHL, tsu, and th are production tested. All other parameters guaranteed but not production tested. 3. Airflow of 1m/s is recommended for frequencies above 500MHz Potato Semiconductor Corporation 3 01/01/10 PO54G74A, PO74G74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS www.potatosemi.com WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic Test Waveforms Timing Input tw tsu VI VM Input VM 0V Data Input VM tPLH tPHL Output 0V tPHL VM Output VI VM VM VOH VOL tPLH VM VM VOH VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 0V th VM VM VI 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION Input VI VM Output Control Output Waveform 1 S1 at V LOAD (see Note B) Output Waveform 2 S1 at GND (see Note B) VM VI VM tPZL tPLZ VM tPZH 0V VLOAD/2 VOL + V VOL tPHZ VM VOH - V VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING Test Circuit Vcc Pulse Generator 50Ohm Potato Semiconductor Corporation D.U.T 15pF to 2pF 4 01/01/10 PO54G74A, PO74G74A www.potatosemi.com DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic Packaging Mechanical Drawing: 14 pin 150mil SOIC 0.244 6.20 0.228 5.80 0.010 0.007 0.050 1.27 0.016 0.40 0.25 0.17 X.XX Denotes dimensions in inches X.XX X.XX Denotes dimensions in millimenters X.XX Packaging Mechanical Drawing: 14pin Leadless Ceramic Chip Carrier X.XX Denotes dimensions in inches X.XX X.XX Denotes dimensions in millimenters X.XX Potato Semiconductor Corporation 5 01/01/10 PO54G74A, PO74G74A DUAL POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOPS www.potatosemi.com WITH CLEAR AND PRESET 54, 74 Series Noise Cancellation GHz Logic Packaging Mechanical Drawing: 20pin Ceramic Dual Flatpack 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 3 2 1 13 12 4 18 5 17 6 16 0.358 (9,09) 7 0.307 (7,80) 15 8 14 0.358 (9,09) 0.342 (8,69) 9 10 11 12 X.XX Denotes dimensions in inches X.XX X.XX Denotes dimensions in millimenters X.XX 13 IC Ordering Information Ordering Code Package Top-Marking TA PO74G74ASU for Tube 14pin SOIC Pb-free & Green POTATO74G74AS -40 C to 125 C PO74G74ASR for Tape & Reel 14pin SOIC Pb-free & Green POTATO74G74AS -40 C to 125 C PO54G74ALU for Tube 14pin Leadless Ceramic Chip Carrier Pb-free & Green POTATO54G74AL -55 C to 125 C PO54G74AFU for Tube 20pin Ceramic Dual Flatpack Pb-free & Green POTATO54G74AF -55 C to 125 C IC Package Information PACKAGE CODE S PACKAGE TYPE TAPE WIDTH (mm) TAPE PITCH (mm) PIN 1 LOCATION TAPE TRAILER LENGTH QTY PER REEL TAPE LEADER LENGTH QTY PER TUBE SOIC 14 16 8 Top Left Corner 39 (12”) 3000 64 (20”) 55 L LCCC 20 N/A N/A N/A N/A N/A N/A 55 F CFP 14 N/A N/A N/A N/A N/A N/A 150 Potato Semiconductor Corporation 6 01/01/10