DC-AC INVERTER UNIT PS-P1212B-091 (8W DOUBLE OUTPUT WITH DIMMING FUNCTION) (MODIFICATION) DESCRIPTION: This DC to AC Inverter was developed for many other low LCD Backlight power supply as low profile applications, either for LCD Optimized for Sharp: LQ121S1DG41 APPLICABLE LCD: 10 to 15 inches double lamp type Lamp Voltage 600V Lamp Current 5,5mA Lamp Start Up Voltage 1700Vrms (Vin : 12V) FEATURES : Current Feedback Circuit High Efficiency Low noise with voltage resonant circuit Regulated output current TEMPERATURE & HUMDITY : Operating Temperature Range Storage Temperature Range Humidity -10 °C ~ +70°C -30 °C ~ +85°C 95 %RH max DIMENSIONS : No. 1 2 3 Part Discription PCB Connector CN1 Connector CN2; CN3 Qty. 1 1 2 Material UL94V-0 (FR-4 or CEM-3) 53261-0790 SM02(8.0)B-BHS-1 21.5±0.5 14±0.3 CN1 Unit : mm Weight :21.2g typ. Note t=1.0mm Molex JST Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specification are subject to change without notice. Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 Page ( 1 / 4 ) VER, 29 Juni 2003 DC-AC INVERTER UNIT PS-P1212B-091 (8W DOUBLE OUTPUT WITH DIMMING FUNCTION) Input Side CN1: Pin No. Symbols CN 1-1 Vin CN 1-2 CN1-3 GND CN1-4 (MODIFICATION) Output Side CN2: Output Side CN3: Pin No. Symbols Ratings VHIGH1 600Vrms CN 2-1 N.C. CN 2-2 VLOW1 (2V) CN 2-3 Ratings 10.8~13.2V 0V Pin No. Symbols Ratings VHIGH2 600Vrms CN 3-1 N.C. CN 3-2 VLOW2 (2V) CN 3-3 0~0.4V:OFF / 2.5V~Vin: ON 0V / 5V The warning Vst output 5V in CN 1-6 abnormal circumstances CN 1-7 Vbr / Rbr 0~2.5V / 0~50k Ω CN 1-5 Vrmt ELECTRICAL CHARACTERISTICS : Conditions Items Symbols Output Current Iout Vin [V] Ta [°C] Iin1 Iin2 F Input Current Frequency Open Circuit Vopen Voltage Dimming Iout1/Iout2 Function W arning Output Vst Specification RL1 [KΩ ] //CL1 [pF] Vbr [V] / RL2 [KΩ ]//CL2 [pF] VR [Ω ] 12±1.2 -10~70 23±5 12±0.6 -10~70 12±0.6 -10~70 85~95//5 90//5 90//5 85~95//5 85~95//5 12±1.2 -10~70 ∞ 12±1.2 12±0.6 -10~70 23±5 85~95//5 90//5 85~95//5 ∞ 12±1.2 -10~70 ∞ 85~95//5 85~95//5 0 0 0 0 0 / / / / / Vrmt [V] Min. Typ. Max. 0 0 0 0 0 5±0.25 0±0.25 5±0.25 0/0 5±0.25 2.5 / 50k 5±0.25 0/0 5±0.25 5±0.25 4.8 5 35 5,5 5,5 0.8 40 1500 1700 6,2 6 1.0 1 45 Unit mArm s Adc mAdc kHz - Vrm s mArm s 1.1 1.2 2.0 2.0 2.9 2.8 4.5 5.0 5.5 - 0 0.5 Vdc DIMMING CHARACTERISTICS (Reference) 6,0 Iout (mArms) 5,0 4,0 3,0 2,0 1,0 0,0 0,0 0,5 1,0 1,5 2,0 2,5 Vbr (VDC) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specification are subject to change without notice. Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 Page ( 2 / 4 ) VER, 29 Juni 2003 DC-AC INVERTER UNIT PS-P1212B-091 (8W DOUBLE OUTPUT WITH DIMMING FUNCTION) (MODIFICATION) APPLICATION (for example) Voltage Dimming Type Iin Q6 CN1-1,2 Vin A V CN1-3,4 GND a b C10 6 CN2-1 Vhigh 9 CN3-1 Vhigh 2 Vin 10.8~13.2V Vrmt 5V T1 1 3 4 RL CN1-5 Vrmt A SW Vbr 0~2.5V Vst RL 5 CN1-7 Vbr CN3-3 Vlow CN1-6 Vst CN2-3 Vlow A Iout2 Iout1 V 1000:1 PROBE F V TEST CIRCUIT Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specification are subject to change without notice. Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 Page ( 3 / 4 ) VER, 29 Juni 2003 DC-AC INVERTER UNIT PS-P1212B-091 (8W DOUBLE OUTPUT WITH DIMMING FUNCTION) (MODIFICATION) Note 1. For circuit connection, please prefer to test circuit diagram Note 2. Please use minimum of 2mm clearance (all directions) between inverter high voltage area and any conductors. Please refer to mechanical drawing for marking of high voltage area. Note 3. Open voltage (strike voltage) is measured across the transformer secondary winding at no load as the reading at the output connector would be less than the actual value Note 4. If the start voltage falls below Cold Cathode Tube strike voltage, the CCFL will not light up easily specially at lower ambient temperature. Please review mounting instruction to avoid any abnormal operation due to coupling/leakage capacitance of inverter high voltage area to any surrounding conductor. Note 5. Please check your lamp characteristic for minimum operational current and set the limit point in your design to avoid flickering and/or abnormal operation. Note 6. For proper operation of circuit protection (FUSE or IC PROTECTOR), please use minimum of 2A capacity for input power supply. Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specification are subject to change without notice. Address: Dörnet 8 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 80 Page ( 4 / 4 ) VER, 29 Juni 2003