LED-CONVERTER UNIT PS-LD0602-023(S) (3 W) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile LED converter is developed for max. 6 LED-lines. Optimized for Optrex: T-51750D065J-LW-AKN, T-51750GD065J-LW-AON APPLICABLE: 1~6 LED lines (Serial Mode) Pout max. 0,9 Watt per line, total max. 3 Watt LED Voltage max. 32V Lamp Current max. 30 mAdc per line FEATURES : Internal Open LED Detection for every Line Analog or ext. PWM Dimming 1000:1 dimming ratio with external PWM Remote ON / OFF Wide Input Voltage Range RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -20°C ~ +70°C -20°C ~ +85°C 95 %RH max 64 x 32 x 6.5 mm Weight :5 (g) typ. Tolerance: +/- 0,3mm Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0890 Note t=1.0mm Molex 3 Connector CN2/CN3 2 SM06B-SHLS-TF(LF)(SN) JST Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.0.2, 16th May 2014 LED-CONVERTER UNIT PS-LD0602-023(S) (3 W) (PRELIMINARY INFORMATION) Input side CN1 Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 CN2 / CN3 Symbols Ratings Vin 4.75 ~ 13.2 Vdc Vin 4.75 ~ 13.2 Vdc Vrmt 0 ~ 0.8 = OFF / 2.5 ~ Vin = ON Ext. PWM 0 ~ 0.5 = LOW / 2.5 ~ 5 = HIGH Vbr 0.0 ~ 5.0 (5V=low brightness) GND GND - CN 1-8 GND Pin No. CN2/ 3-1 CN2/ 3-2 CN2/ 3-3 CN2/ 3-4 CN2/ 3-5 Symbols RTN4 (+) RTN3 (+) RTN2 (-) Ratings LED LINE 6 RETURN LED LINE 5 RETURN N.C N.C LED LINE 2 RETURN CN2/ 3-6 RTN1 (-) LED LINE 1 RETURN - ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Open Load Shutdown PWM Frequency Output Power Output Power Output Power Output Power Iout Imin Iin Vbias f(PWM) Pout Pout Pout Pout Specification Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 4.75 ~ 13.2 0 5 0 0 0 0 0 0 0 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+50 -20~+70 28 0.06 150 TBD TBD TBD TBD 30 10 32 3 1.9 0.9 0.6 32 0.8 300 TBD TBD TBD TBD Vin 4.75 ~ 13.2 Vdc TEST CIRCUIT : Iin A CN1-2 mAdc % Adc Vdc Hz Watt Watt Watt Watt Duty 100%, max current dut y cycle Tu: -20~+50degC Tu: -20~+70degC For one line For one line CN 2-7 D1 D1 D2 D2 D6 D6 a V Ext. PWM 0. 0 ~ 5.0 Connect Vbr to Ground while using ext. PWM dimming. Note CN1-1 V Vrmt 1. 5 / 2. 5 Vdc Unit Vbr 0. 0 ~ 5. 0 Vdc b SW1 CN1-3 CN1-4 SW2 CN1-5 SW3 CN 2-6 A ~ CN 2-1 A ~ CN1-6 CN1-7 CN1-8 Note 1 : Note 2 : Note 3: Do not use analog dimming and external PWM dimming at the same time. External PWM-signal is LOW active. Connect Vbr to ground while using external PWM dimming. CABLES: for input: 500 mm, stripped and tinned ends, order key <input cable #13> Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.0.2, 16th May 2014