File E193009 Vol. 2 Sec. 6 and Report Page 1G Issued: Revised: 2002-02-07 2005-02-09 ELECTRICAL RATING: Model PFKC03-05S33Z-Z1Z1Z1 PFKC03-05S05Z-Z1Z1Z1 PFKC03-05S12Z-Z1Z1Z1 Input (dc) V 4.5-6 or 5 4.5-6 or 5 4.5-6 or 5 Output(dc) mA mA V 710 1010 926 3.3 5 12 600 600 250 File E193009 Vol. 2 Sec. 6 and Report Page 2 Issued: Revised: 2002-02-07 2005-02-09 ELECTRICAL RATING (CONTINUED): Input (dc) Output(dc) mA Model V mA V PFKC03-05S15Z-Z1Z1Z1 PFKC03-05D05Z-Z1Z1Z1 PFKC03-05D12Z-Z1Z1Z1 PFKC03-05D15Z-Z1Z1Z1 PFKC03-12S33Z-Z1Z1Z1 PFKC03-12S05Z-Z1Z1Z1 PFKC03-12S12Z-Z1Z1Z1 PFKC03-12S15Z-Z1Z1Z1 PFKC03-12D05Z-Z1Z1Z1 PFKC03-12D12Z-Z1Z1Z1 PFKC03-12D15Z-Z1Z1Z1 PFKC03-24S33Z-Z1Z1Z1 PFKC03-24S05Z-Z1Z1Z1 PFKC03-24S12Z-Z1Z1Z1 PFKC03-24S15Z-Z1Z1Z1 PFKC03-24D05Z-Z1Z1Z1 PFKC03-24D12Z-Z1Z1Z1 PFKC03-24D15Z-Z1Z1Z1 PFKC03-48S33Z-Z1Z1Z1 PFKC03-48S05Z-Z1Z1Z1 PFKC03-48S12Z-Z1Z1Z1 PFKC03-48S15Z-Z1Z1Z1 PFKC03-48D05Z-Z1Z1Z1 PFKC03-48D12Z-Z1Z1Z1 PFKC03-48D15Z-Z1Z1Z1 4.5-6 or 5 4.5-6 or 5 4.5-6 or 5 4.5-6 or 5 9-18 or 12 9-18 or 12 9-18 or 12 9-18 or 12 9-18 or 12 9-18 or 12 9-18 or 12 18-36 or 24 18-36 or 24 18-36 or 24 18-36 or 24 18-36 or 24 18-36 or 24 18-36 or 24 36-75 or 48 36-75 or 48 36-75 or 48 36-75 or 48 36-75 or 48 36-75 or 48 36-75 or 48 939 ±966 ±939 ±966 334 470 445 457 ±463 ±450 ±445 165 232 220 220 ±228 ±223 ±223 81 118 112 112 ±115 ±112 ±112 15 5 12 15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 200 ±300 ±125 ±100 600 600 250 200 ±300 ±125 ±100 600 600 250 200 ±300 ±125 ±100 600 600 250 200 ±300 ±125 ±100 File E193009 Vol. 2 Sec. 6 and Report Page 4 Issued: Revised: 2002-02-07 2005-02-09 Conditions of Acceptability - When installed in the end-product, consideration shall be given to the following: 1. This component has been judged on the basis of required spacing in the Standard for Safety of Information Technology Equipment, CAN/CSA C22.2 No. 60950-1 and UL 60950-1 First Edition, dated April 1, 2003, Sub-clause 2.10, which would cover the component itself if submitted for Listing. 2. The products were tested on a 5 A time delay fuse protection circuit. If used on a protection circuit greater than this, additional testing may be necessary. 3. All secondary output circuits are SELV and are not hazardous energy levels. 4. The terminals and connectors are suitable for factory wiring only. 5. The equipment has been evaluated for use in a Pollution Degree 2 environment. 6. A suitable Electrical and Fire enclosure shall be provided. 7. The component is intended to be connected to isolated secondary circuit which is separated from primary circuit by Reinforced or Double insulation. 8. All models withstood 3200 V dc Electric Strength Test.