COA

File E193009
Vol. 2
and Report
Sec. 5
Page 1-13
Issued: 2002-01-17
Revised: 2005-03-25
ELECTRICAL RATING:
Input (dc)
Model
FKC03-12S33FKC03-12S05FKC03-12S12FKC03-12S15FKC03-12D05FKC03-12D12FKC03-12D15FKC03-24S33FKC03-24S05FKC03-24S12FKC03-24S15FKC03-24D05FKC03-24D12FKC03-24D15FKC03-48S33FKC03-48S05FKC03-48S12FKC03-48S15FKC03-48D05FKC03-48D12FKC03-48D15-
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
z1z1z1z1z1z1
V
9~18 or 12
9~18 or 12
9~18 or 12
9~18 or 12
9~18 or 12
9~18 or 12
9~18 or 12
18~36 or 24
18~36 or 24
18~36 or 24
18~36 or 24
18~36 or 24
18~36 or 24
18~36 or 24
36~75 or 48
36~75 or 48
36~75 or 48
36~75 or 48
36~75 or 48
36~75 or 48
36~75 or 48
mA
277
407
463
457
397
463
451
143
210
238
238
210
241
238
69
106
116
118
107
116
121
V
3.3
5
12
15
±5
±12
±15
3.3
5
12
15
±5
±12
±15
3.3
5
12
15
±5
±12
±15
Output(dc)
mA
500
500
250
200
±250
±125
±100
500
500
250
200
±250
±125
±100
500
500
250
200
±250
±125
±100
File E193009
Vol. 2
and Report
Sec. 5
Page 5
Issued: 2002-01-17
Revised: 2005-03-25
Conditions of Acceptability - When installed in the end-product,
consideration shall be given to the following:
1.
This component has been judged on the basis of required spacing in the
Standard for Safety of Information Technology Equipment, CAN/CSA-C22.2
No. 60950-1-03 * UL60950-1, First Edition, including revisions through
revision dated November 26, 2003, which would cover the component itself
if submitted for Listing.
2.
The products were tested on a 6.3A time delay fuse protection circuit.
If used on a protection circuit greater than this, additional testing
may be necessary.
3.
All secondary output circuits are SELV and are not hazardous energy
levels.
4.
The terminals and connectors are suitable for factory wiring only.
5.
The equipment has been evaluated for use in a Pollution Degree 2
environment.
6.
A suitable Electrical and Fire enclosure shall be provided.
7.
The component is intended to be connected to isolated secondary circuit
which is separated from primary circuit by Reinforced or Double
insulation.