INTRODUCTION TO THE CATALOG The interconnect components presented in this catalog are of two different types: -pin receptacles also called socket contacts or female contacts -pins also called terminals or male contacts. Receptacles are made by assembling a machined shell or body (A) with a stamped multi-finger spring contact (B). The shells, machined by high speed turning process, are designed with closed bottom for wicking free solder and protection against contamination by flux. The standard available contacts accept pins (C) with diameter (D) ranging from 0.3 to 2.6 mm. As shells and contacts are manufactured and plated separately, they can be designed or selected individually to fulfill the application requirements without any compromise. Pins are manufactured by the same high speed turning process as shells. Both types are available with different type of terminations: A B Basic receptacle D C Basic pin Possible terminations : -PCB solder tail -PCB press-fit into plated-thru holes for solderless connection with solid or compliant pin -Wrapost -Wiring solder-cup, slot or turret -Wiring crimp The parts presented in this catalogue are grouped in 4 sections. For easy searching, the receptacles are classified by increasing diameter of the accepted pin and the other components by increasing size within the sections. NOTE: -All dimensions in this catalog are in mm unless otherwise specified -All right reserved. Copyright E DURTAL SA -All the informations provided by this catalog is subject to change without notice. C2 1 CONTENTS PAGE PIN RECEPTACLES PRESS-FIT MOUNT SOLDER MOUNT CONNECTORS 2 PAGE WRAPOST PIN RECEPTACLES 30 PAGE PINS PRESS-FIT MOUNT 32 SOLDER MOUNT CONNECTORS PAGE WRAPOST TERMINALS 44 PAGE SPECIFICATIONS 47 INSIDE BACK COVER NUMERICAL INDEX C2 2 PIN RECEPTACLE FOR DIA. 0.40 to 0.53 mm (.016 to .021") 01503 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01503-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01503-91-1210 01503-93-1210 01503-97-1210 01503-99-1210 01505 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057" ) REF.no : 01505-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 01505-91-1210 01505-93-1210 DIMENSIONS IN mm TOLERANCE ON : 1210 = 4 finger short normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 3 PIN RECEPTACLE FOR DIA. 0.40 to 0.54 mm (.016 to .021") 01402 SOLDER MOUNT : hole dia. 1,10 mm (.043") REF.no : 01402-XX-XXXX A B STANDARD TYPES : (order no) 01402-93-1110 01402-99-1110 01408 PRESS-FIT MOUNT : hole dia. 1,05 mm (.041") 014XX SOLDER MOUNT : hole dia. 1,02 mm (.040") REF.no : 014XX-XX-XXXX X A B STANDARD TYPES : (order no) 014XX-91-1110 014XX-93-1110 014XX-99-1110 01418 SOLDER MOUNT : hole dia. 1,02 mm (.040") STANDARD TYPES : (order no) 01408-93-1110 STANDARD TYPES : (order no) 01418-93-1110 REF.no : 01408-XX-XXXX A B REF.no : 01418-XX-XXXX A B 01421 SOLDER MOUNT : hole dia. 1,02 mm (.040") 01423 SOLDER MOUNT : hole dia. 1,02 mm (.040") STANDARD TYPES : (order no) 01421-93-1110 REF.no : 01421-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01423-13-1110 REF.no : 01423-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 1110 = 3 finger low force SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 4 PIN RECEPTACLE FOR DIA. 0.40 to 0.54 (.016 to .021") 01425 SOLDER MOUNT : hole dia. 1,02 mm (.040") REF.no : 01425-XX-XXXX A B STANDARD TYPES : (order no) 01425-91-1110 01425-93-1110 01429 SOLDER MOUNT : hole dia. 1,02 mm (.040") 01428 SOLDER MOUNT : hole dia. 1,02 mm (.040") STANDARD TYPES : (order no) 01428-99-1110 REF.no : 01428-XX-XXXX A B 01404 SOLDER MOUNT : hole dia. 1,32 mm (.052") STANDARD TYPES : (order no) 01429-97-1110 REF.no : 01429-XX-XXXX A B REF.no : 01404-XX-XXXX A B STANDARD TYPES : (order no) 01404-93-1110 01430 SOLDER MOUNT : hole dia. 1,06 mm (.041") STANDARD TYPES : (order no) 01430-93-1110 REF.no : 01430-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 1110 = 3 finger low force SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 5 PIN RECEPTACLE FOR DIA. 0.40 to 0.54 mm (.016 to .021") 03101 SOLDER MOUNT : hole dia. 1.00 mm (.039") 03103 SOLDER MOUNT : hole dia. 1,00 mm (.039") THRU-HOLE REF.no : 03101-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb THRU-HOLE STANDARD TYPES : (order no) 03101-93-1110 REF.no : 03103-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 03103-13-1110 DIMENSIONS IN mm TOLERANCE ON : 1110 = 3 finger low force SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 6 PIN RECEPTACLE FOR DIA. 0.40 to 0.54 mm (.016 to .021") 100XX PRESS-FIT MOUNT : hole dia. 1,04 mm (.041") X= X= REF.no : 100XX-XX-XXXX X A B A =STANDARD PLATING CODE 1000X PRESS-FIT MOUNT : hole dia. 1,04 mm (.041") SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 100XX-91-1110 100XX-93-1110 100XX-99-1110 REF.no : 1000X-XX-XXXX X A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 1000X-91-1110 1000X-93-1110 1000X-99-1110 DIMENSIONS IN mm TOLERANCE ON : 1110 = 3 finger low force SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 7 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 (.016 to .022") 01411PRESS-FIT MOUNT : hole dia. 1,38 mm (.054") 01417PRESS-FIT MOUNT : hole dia. 1,38 mm (.054") STANDARD TYPES : (order no) 01411-93-3010 STANDARD TYPES : (order no) 01417-91-3010 01417-93-3010 01417-99-3010 REF.no : 01411-XX-XXXX A B REF.no : 01417-XX-XXXX A B 01406 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01427 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01406-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01406-91-3010 01406-93-3010 01406-99-3010 STANDARD TYPES : (order no) 01427-93-3010 REF.no : 01427-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 8 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 014XX SOLDER MOUNT : hole dia. 1,45 mm (.057") STANDARD TYPES : (order no) 014XX-13-3010 014XX-91-3010 014XX-93-3010 014XX-99-3010 REF.no : 014XX-XX-XXXX X A B 01431 SOLDER MOUNT : hole dia. 1,45 mm (.057") REF.no : 01431-XX-XXXX A B STANDARD TYPES : (order no) 01431-99-3010 01420 SOLDER MOUNT : hole dia. 1,58 mm (.062") 01405 SOLDER MOUNT : hole dia. 1,47 mm (.058") STANDARD TYPES : (order no) 01405-93-3010 REF.no : 01405-XX-XXXX A B 01426 SOLDER MOUNT : hole dia. 1,73 mm (.068") STANDARD TYPES : (order no) 01420-93-3010 REF.no : 01426-XX-XXXX A B REF.no : 01420-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01426-93-3010 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 9 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01001 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01005 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01001-13-3010/3110 01001-97-3010/3110 01001-91-3010/3110 01001-93-3010/3110 01001-99-3010/3110 SLEEVE = soft brass STANDARD TYPES : (order no) 01005-91-3010 01005-93-3010 01005-99-3010 REF.no : 01001-XX-XXXX A B REF.no : 01005-XX-XXXX A B 01007 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01008 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01007-XX-XXXX A B STANDARD TYPES : (order no) 01007-91-3010 01007-99-3010 01016 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01008-XX-XXXX A B 01017 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01016-93-3010 REF.no : 01016-XX-XXXX A B A =STANDARD PLATING CODE STANDARD TYPES : (order no) 01008-93-3010 01008-99-3010 REF.no : 01017-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 01017-91-3010 01017-93-3010 01017-99-3010 DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 3110 = 6 finger low force CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 10 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 (.016 to .022") 01009 PRESS-FIT MOUNT : hole dia. 1,52 mm (.060") REF.no : 01009-XX-XXXX A B STANDARD TYPES : (order no) 01009-93-3010 01108 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01108-XX-XXXX A B STANDARD TYPES : (order no) 01108-93-3010 01308 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 01308-XX-XXXX A B A =STANDARD PLATING CODE STANDARD TYPES : (order no) 01308-93-3010 01308-93-3110 01115 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01115-99-3010 REF.no : 01115-XX-XXXX A B 01315 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01315-93-3110 REF.no : 01315-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 3110 = 6 finger low force CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 11 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 011XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 011XX-91-3010 011XX-93-3010 011XX-99-3010 REF.no : 011XX-XX-XXXX X A B 016XXPRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 016XX-91-3010 016XX-93-3010 016XX-99-3010 REF.no : 016XX-XX-XXXX X A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 12 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01201 SOLDER MOUNT : hole dia. 1,45 mm (.057") REF.no : 01201-XX-XXXX A B STANDARD TYPES : (order no) 01201-13-3010 01201-91-3010 01201-93-3010 01201-99-3010 01204 SOLDER MOUNT : hole dia. 1,45 mm (.057") 01202 SOLDER MOUNT : hole dia. 1,45 mm (.057") REF.no : 01202-XX-XXXX A B 01205 SOLDER MOUNT : hole dia. 1,45 mm (.057") STANDARD TYPES : (order no) 01204-91-3010 REF.no : 01204-XX-XXXX A B STANDARD TYPES : (order no) 01202-93-3010 01202-99-3010 STANDARD TYPES : (order no) 01205-13-3010 REF.no : 01205-XX-XXXX A B 01206 SOLDER MOUNT : hole dia. 1,45 mm (.057") STANDARD TYPES : (order no) 01206-99-3010 REF.no : 01206-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 13 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01501 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01501-XX-XXXX A B STANDARD TYPES : (order no) 01501-13-3010 01501-91-3010 01501-93-3010 01501-99-3010 01702 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01702-XX-XXXX A B STANDARD TYPES : (order no) 01702-13-3010 01702-99-3010 01711 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01507 PRESS-FIT MOUNT : hole dia. 1.44 mm (.057") REF.no : 01507-XX-XXXX A B 01705 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01705-XX-XXXX A B A =STANDARD PLATING CODE STANDARD TYPES : (order no) 01705-91-3010 01705-93-3010 01705-99-3010 01705-93-3110 01714 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01711-93-3110 REF.no : 01711-XX-XXXX A B STANDARD TYPES : (order no) 01507-91-3010 01507-93-3110 STANDARD TYPES : (order no) 01714-93-3110 REF.no : 01714-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 3110 = 6 finger low force CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 14 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01909 SOLDER MOUNT : hole dia. 1,40 mm (.055") 01903 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01909-93-3010 STANDARD TYPES : (order no) 01903-93-3010 REF.no : 01909-XX-XXXX A B REF.no : 01903-XX-XXXX A B 01908 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01912 PRESS-FIT MOUNT : hole dia. 1.44 mm (.057") STANDARD TYPES : (order no) 01908-93-3010 REF.no : 01908-XX-XXXX A B STANDARD TYPES : (order no) 01912-99-3010 REF.no : 01912-XX-XXXX A B 01901 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 01901-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01901-91-3010 01901-93-3010 01901-99-3010 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 15 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 009XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 018XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") SLEEVE=Bronze STANDARD TYPES : (order no) 009XX-93-3010 STANDARD TYPES : (order no) 018XX-13-3010 REF.no : 009XX-XX-XXXX X A B REF.no : 018XX-XX-XXXX X A B 01904 PRESS-FIT MOUNT : hole dia. 1,50 mm (.059") 0190X PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01904-93-3010 REF.no : 0190X-XX-XXXX X A B REF.no : 01904-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 0190X-99-3010 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 16 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01910 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 019XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01910-93-3010 STANDARD TYPES : (order no) 019XX-93-3010 REF.no : 01910-XX-XXXX A B REF.no : 019XX-XX-XXXX X A B 01913 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01914 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01913-93-3110 REF.no : 01913-XX-XXXX A B A =STANDARD PLATING CODE STANDARD TYPES : (order no) 01914-99-3010 REF.no : 01914-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 3110 = 6 finger low force CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 17 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 01915 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01916 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01915-91-3010 STANDARD TYPES : (order no) 01916-93-3010 REF.no : 01915-XX-XXXX A B REF.no : 01916-XX-XXXX A B 01917 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 01918 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 01917-91-3010 REF.no : 01917-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01918-91-3010 REF.no : 01918-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 18 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 02502 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 02503 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 0.96-1.10 mm (.038-.043") PCB hole dia. 0.96-1.10 mm (.038-.043") SLEEVE=Bronze SLEEVE=Bronze REF.no : 02502-XX-XXXX A B STANDARD TYPES : (order no) 02502-93-3110 02502-99-3010 REF.no : 02503-XX-XXXX A B STANDARD TYPES : (order no) 02503-99-3010 0250X PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 0.96-1.10 mm (.038-.043") SLEEVE=Bronze REF.no : 0250X-XX-XXXX X A B A =STANDARD PLATING CODE STANDARD TYPES : (order no) 0250X-99-3010 B=INSERTION CARACTERISTICS MATERIALS : SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE 91 = 5 um SnPb 0.25um Au 3110 = 6 finger low force CONTACT = BeCu 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb DIMENSIONS IN mm TOLERANCE ON : = Bronze LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 19 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 04602 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 04603 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.00 mm (.039") PCB hole dia. 1.05 mm (.041") STANDARD TYPES : (order no) 04602-91-3010 REF.no : 04602-XX-XXXX A B STANDARD TYPES : (order no) 04603-93-3010 REF.no : 04603-XX-XXXX A B 04610 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1,00 mm (.039") REF.no : 04610-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 04610-93-3010 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 20 PIN RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 04605 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.05 mm (.041") 04606 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.05 mm (.041") STANDARD TYPES : (order no) 04605-93-3010 STANDARD TYPES : (order no) 04606-93-3010 REF.no : 04605-XX-XXXX A B REF.no : 04606-XX-XXXX A B 04612 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 04613 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.00 mm (.039") PCB hole dia. 1.00 mm (.039") STANDARD TYPES : (order no) 04612-93-3010 REF.no : 04612-XX-XXXX A B STANDARD TYPES : (order no) 04613-93-3010 REF.no : 04613-XX-XXXX A B 01324 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01324-93-1410 REF.no : 01324-XX-XXXX A B A =STANDARD PLATING CODE B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 1410 = 6 finger normal CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 21 PIN RECEPTACLE FOR DIA. 0.56 to 0.86 (.022 to .034") 01309 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 03102 SOLDER MOUNT : hole dia. 1,62 mm (.064") THRU-HOLE REF.no : 01309-XX-XXXX A B STANDARD TYPES : (order no) 01309-93-1610 01309-99-1610 STANDARD TYPES : (order no) 03102-93-1610 REF.no : 03102-XX-XXXX A B 15000 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 15000-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 15000-13-1610 15000-93-1610 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 1610 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 22 PIN RECEPTACLE FOR DIA. 0.63 to 0.90 (.025 to .035") 01303 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 01303-XX-XXXX A B STANDARD TYPES : (order no) 01303-93-4710 01303-99-4710 01305 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 01305-XX-XXXX A B STANDARD TYPES : (order no) 01305-91-4710 01305-93-4710 01305-99-4710 01317 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 01304 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 01304-XX-XXXX A B 01306 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") REF.no : 01306-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01306-91-4710 01306-93-4710 01306-99-4710 01319 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01317-99-4710 REF.no : 01317-XX-XXXX A B STANDARD TYPES : (order no) 01304-91-4710 01304-93-4710 01304-99-4710 REF.no : 01319-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 01319-93-4710 DIMENSIONS IN mm TOLERANCE ON : 4710 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 23 PIN RECEPTACLE FOR DIA. 0.63 to 0.90 (.025 to .035") 01320 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 01323 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01320-93-4710 STANDARD TYPES : (order no) 01323-93-4710 01323-99-4710 REF.no : 01320-XX-XXXX A B REF.no : 01323-XX-XXXX A B 04614 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 04615 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") PCB hole dia. 1.00 mm (.039") PCB hole dia. 1.00 mm (.039") REF.no : 04614-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 04614-93-4710 04614-99-4710 REF.no : 04615-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 04615-93-4710 04615-99-4710 DIMENSIONS IN mm TOLERANCE ON : 4710 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 24 PIN RECEPTACLE FOR DIA. 0.63 to 0.90 mm (.025 to .035") 01316 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 01318 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01316-91-4710 STANDARD TYPES : (order no) 01318-93-4710 REF.no : 01316-XX-XXXX A B REF.no : 01318-XX-XXXX A B 01321 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") 01322 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 01321-91-4710 REF.no : 01321-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 01322-91-4710 REF.no : 01322-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 4710 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 25 PIN RECEPTACLE FOR DIA. 0.99 to 1.05 mm (.039 to .041") 01313 PRESS-FIT MOUNT : hole dia. 1,36 mm (.054") 10007 SOLDER MOUNT : hole dia. 2.10 mm (.080") STANDARD TYPES : (order no) 01313-93-1810 STANDARD TYPES : (order no) 10007-13-1810 REF.no : 01313-XX-XXXX A B REF.no : 10007-XX-XXXX A B 15007 SOLDER MOUNT : hole dia. x,xx mm (.xxx") 15008 SOLDER MOUNT : hole dia. 2,10 mm (.080") STANDARD TYPES : (order no) 15007-93-1810 STANDARD TYPES : (order no) 15008-13-1810 REF.no : 15007-XX-XXXX A B REF.no : 15008-XX-XXXX A B 15009 SOLDER MOUNT : hole dia. 2,10 mm (.080") 15015 SOLDER MOUNT : hole dia. 2,10 mm (.080") STANDARD TYPES : (order no) 15009-13-1810 REF.no : 15009-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 15015-93-1810 REF.no : 15015-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 1810 = 6 finger short normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 26 PIN RECEPTACLE FOR DIA. 0.99 to 1.05 mm (.039 to .041") 6001X PRESS-FIT MOUNT : hole dia. 1,76 mm (.069") 60012 PRESS-FIT MOUNT : hole dia. 1,93 mm (.76") STANDARD TYPES : (order no) 6001X-93-1811 REF.no : 6001X-XX-XXXX X A B STANDARD TYPES : (order no) 60012-93-1811 REF.no : 60012-XX-XXXX A B 6002X PRESS-FIT MOUNT : hole dia. 1,90 mm (.075") REF.no : 6002X-XX-XXXX X A B A =STANDARD PLATING CODE SLEEVE CONTACT 14 = 0.25um Au 1.27um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au STANDARD TYPES : (order no) 6002X-93-1811 B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 1811 = 6 finger short normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 27 PIN RECEPTACLE FOR DIA. 0.99 to 1.05 mm (.039 to .041") 65002 65010 REF.no : 65002-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 14 = 0.25um Au 1.27um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au STANDARD TYPES : (order no) 65002-14-1811 REF.no : 65010-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 65010-93-1811 DIMENSIONS IN mm TOLERANCE ON : 1811 = 6 finger short normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 28 PIN RECEPTACLE FOR DIA. 1.01 to 1.32 mm (.040 to .052") 0170X PRESS-FIT MOUNT : hole dia. 2,02 mm (.080") STANDARD TYPES : (order no) 0170X-93-2711 REF.no : 0170X-XX-XXXX X A B A =STANDARD PLATING CODE SLEEVE CONTACT 14 = 0.25um Au 1.27um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 2711 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 29 PIN RECEPTACLE FOR DIA. 1,56 to 1.61 mm (.0615 to .0635") 60006 60008 STANDARD TYPES : (order no) 60006-95-3920 REF.no : 60006-XX-XXXX A B STANDARD TYPES : (order no) 60008-14-3920 REF.no : 60008-XX-XXXX A B 60009 60014 STANDARD TYPES : (order no) 60009-14-3920 REF.no : 60009-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 14 = 0.25um Au 1.27um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 95 = 0.25um Au 2.54um Au 97 = 5 um SnPb Flash Au STANDARD TYPES : (order no) 60014-14-3920 REF.no : 60014-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm TOLERANCE ON : 3920 = 6 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 30 WRAPOST RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 04609 PRESS-FIT MOUNT : hole dia. 1,09 mm (.043") REF.no : 04609-XX-XXXX A B STANDARD TYPES : (order no) 04609-93-3010 04609-99-3010 02201 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 02201-XX-XXXX A B STANDARD TYPES : (order no) 02201-13-3010 02201-91-3010 02201-93-3010 02201-99-3010 02402 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 02402-XX-XXXX A B A =STANDARD PLATING CODE SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 91 = 5 um SnPb 0.25um Au 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb STANDARD TYPES : (order no) 02402-13-3010 02402-93-3010 02402-99-3010 02101 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 02101-XX-XXXX A B STANDARD TYPES : (order no) 02101-13-3010 02101-93-3010 02101-99-3010 02301 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 02301-XX-XXXX A B STANDARD TYPES : (order no) 02301-13-3010 02301-91-3010 02301-93-3010 02301-99-3010 02304 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 02304-XX-XXXX A B B=INSERTION CARACTERISTICS MATERIALS : STANDARD TYPES : (order no) 02304-13-3010 02304-93-3010 DIMENSIONS IN mm TOLERANCE ON : 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 CONTACT = BeCu DIA. : + 0.07 / - 0.03 C2 31 WRAPOST RECEPTACLE FOR DIA. 0.40 to 0.56 mm (.016 to .022") 0260X PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 0260X-XX-XXXX X A B STANDARD TYPES : (order no) 0260X-13-3010 0260X-91-3010 0260X-93-3010 0270X PRESS-FIT MOUNT : hole dia. 1,40 mm (.055") STANDARD TYPES : (order no) 0270X-93-3010 REF.no : 0270X-XX-XXXX X A B 20011 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") STANDARD TYPES : (order no) 20011-93-4710 REF.no : 20011-XX-XXXX A B A =STANDARD PLATING CODE B=INSERTION CARACTERISTICS MATERIALS : DIMENSIONS IN mm SLEEVE CONTACT 13 = 0.25um Au 0.75um Au 3010 = 4 finger normal SLEEVE = brass LENGTHS : +/- 0.10 91 = 5 um SnPb 0.25um Au 4710 = 6 finger normal CONTACT = BeCu DIA. : + 0.07 / - 0.03 93 = 5 um SnPb 0.75um Au 97 = 5 um SnPb Flash Au 99 = 5 um SnPb 4 um SnPb TOLERANCE ON : C2 32 PINS - PRESS-FIT - 50019 PRESS-FIT MOUNT : hole dia. 0,65 mm (.026") STANDARD TYPES : (order no) 50019-90 500XX PRESS-FIT MOUNT : hole dia. 0,85 mm (.033") STANDARD TYPES : (order no) 500XX-10 500XX-90 REF.no : 50019-XX A REF.no : 500XX-XX X A 03003 PRESS-FIT MOUNT : hole dia. 0.85 mm (.033") 50005 PRESS-FIT MOUNT : hole dia. 1,05 mm (.041") STANDARD TYPES : (order no) 03003-30 STANDARD TYPES : (order no) 50005-10 REF.no : 03003-XX A REF.no : 50005-XX A 03301 PRESS-FIT MOUNT : hole dia. 1.03 mm (.041") 05019 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 03301-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 03301-10 03301-90 STANDARD TYPES : (order no) 05019-10 05019-90 REF.no : 05019-XX A MATERIALS : SLEEVE 10 = 0.25um Au 30 = 0.75um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 33 PINS - PRESS-FIT - 05024 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 05020 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") SLEEVE = Bronze STANDARD TYPES : (order no) 05024-90 STANDARD TYPES : (order no) 05020-10 05020-90 REF.no : 05024-XX A REF.no : 05020-XX A 05008 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 05017 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05008-XX A STANDARD TYPES : (order no) 05008-10 05008-90 05016 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05016-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 05016-10 05016-90 STANDARD TYPES : (order no) 05017-10 05017-90 REF.no : 05017-XX A 05006 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05006-10 05006-90 REF.no : 05006-XX A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 34 PINS - PRESS-FIT - 05013 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05013-XX A STANDARD TYPES : (order no) 05013-10 05013-90 05002 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05002-XX A STANDARD TYPES : (order no) 05002-10 05002-90 05001 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05001-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 05001-10 05001-90 05007 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05007-10 05007-90 REF.no : 05007-XX A 05012 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05012-10 05012-90 REF.no : 05012-XX A 05018 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05018-10 05018-90 REF.no : 05018-XX A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 35 PINS - PRESS-FIT - 050XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 050XX-XX X A STANDARD TYPES : (order no) 050XX-10 050XX-90 05010 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05010-XX A STANDARD TYPES : (order no) 05010-10 05010-90 05014 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05014-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 05014-10 05014-90 05023 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05023-90 REF.no : 05023-XX A 05009 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05009-10 05009-90 REF.no : 05009-XX A 07001 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 07001-10 07001-90 REF.no : 07001-XX A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 36 PINS - PRESS-FIT - 051XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 051XX-XX X A 05102 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05102-10 05102-90 STANDARD TYPES : (order no) 051XX-10 051XX-90 REF.no : 05102-XX A 05120 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05120-XX A A =STANDARD PLATING CODE SLEEVE 10 = 0.25um Au 90 = 5 um SnPb STANDARD TYPES : (order no) 05120-10 05120-90 MATERIALS : DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 37 PINS - PRESS-FIT - 05115 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 05115-XX A STANDARD TYPES : (order no) 05115-10 05115-90 05118 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05118-10 05118-90 REF.no : 05118-XX A 05124 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 05124-10 REF.no : 05124-XX A A =STANDARD PLATING CODE SLEEVE 10 = 0.25um Au 90 = 5 um SnPb MATERIALS : DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 38 PINS - PRESS-FIT - 051XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 051XX-XX X A STANDARD TYPES : (order no) 051XX-10 051XX-90 051XX PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 051XX-XX X A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 051XX-10 051XX-90 0512X PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 0512X-10 0512X-90 REF.no : 0512X-XX X A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 39 PINS - PRESS-FIT - 50027 PRESS-FIT MOUNT : hole dia. 0,60 mm (..024") REF.no : 50027-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) UNPLATED 5003X PRESS-FIT MOUNT : hole dia. 0,60 mm (.024") STANDARD TYPES : (order no) UNPLATED REF.no : 5003X-XX X A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 40 PINS - PRESS-FIT - 05601 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.00 mm (.039") REF.no : 05601-XX A STANDARD TYPES : (order no) 05601-10 05601-90 06001 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 06001-XX A STANDARD TYPES : (order no) 06001-10 06001-90 08501 PRESS-FIT MOUNT : hole dia. 1,50 mm (.059") REF.no : 08501-XX A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 08501-10 08501-90 05602 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") PCB hole dia. 1.00 mm (.039") STANDARD TYPES : (order no) 05602-10 05602-90 REF.no : 05602-XX A 08001 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 08001-10 08001-90 REF.no : 08001-XX A 0320X PRESS-FIT MOUNT : hole dia. 1,50 mm (.059") STANDARD TYPES : (order no) 0320X-10 0320X-90 REF.no : 0320X-XX X A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 41 PINS - SOLDER - 50015 SOLDER MOUNT : hole dia. 0,60 mm (.024") 50016 SOLDER MOUNT : hole dia. 0,70 mm (.028") STANDARD TYPES : (order no) 50015-90 REF.no : 50015-XX A STANDARD TYPES : (order no) 50016-10 REF.no : 50016-XX A 50026 SOLDER MOUNT : hole dia. 1,80 mm (.071") 03204 SOLDER MOUNT : hole dia. 0,70 mm (.028") STANDARD TYPES : (order no) 50026-90 REF.no : 50026-XX A STANDARD TYPES : (order no) 03204-10 03204-90 REF.no : 03204-XX A 05501 SOLDER MOUNT : hole dia. 0,70 mm (.028") 03207 SOLDER MOUNT : hole dia. 0,89 mm (.035") STANDARD TYPES : (order no) 03207-10 STANDARD TYPES : (order no) 05501-40 REF.no : 05501-XX A A =STANDARD PLATING CODE REF.no : 03207-XX A MATERIALS : SLEEVE 10 = 0.25um Au 40 = 1.27um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 42 PINS - CONNECTORS - 75001 75010 REF.no : 75001-XX A A =STANDARD PLATING CODE STANDARD TYPES ; (order no: 75001-10 75001-90 STANDARD TYPES ; (order no: 75010-10 75010-90 REF.no : 75010-XX A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 43 PINS - CONNECTORS - 0350X PRESS-FIT MOUNT : hole dia. 1,20 mm (.047") REF.no : 0350X-XX X A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 0350X-10 70004 STANDARD TYPES : (order no) 70004-40 REF.no : 70004-XX A MATERIALS : SLEEVE 10 = 0.25um Au 40 = 1.27um Au DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 44 PINS - WRAPOST TERMINAL - 04XXX PRESS-FIT MOUNT : hole dia. 0,97 mm (.038") 02X01 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") ( without hole ) REF.no : 04XXX-XX X A STANDARD TYPES ; (order no: 04XXX-10 04XXX-90 02X09 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES ; (order no: 02X01-10 02X01-90 REF.no : 02X01-XX X A 05X01 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") ( without hole ) REF.no : 02X09-XX X A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 02X09-10 02X09-90 STANDARD TYPES : (order no) 05X01-10 05X01-90 REF.no : 05X01-XX X A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 45 PINS - WRAPOST TERMINAL - 06302 PRESS-FIT MOUNT : hole dia. 0,97 mm (.038") REF.no : 06302-XX A STANDARD TYPES : (order no) 06302-10 06302-90 07X01 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") REF.no : 07X01-XX X A A =STANDARD PLATING CODE STANDARD TYPES : (order no) 07X01-10 07X01-90 06X01 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 06X01-10 06X01-90 REF.no : 06X01-XX X A 08X01 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") STANDARD TYPES : (order no) 08X01-10 08X01-90 REF.no : 08X01-XX X A MATERIALS : SLEEVE 10 = 0.25um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 46 PINS - WRAPOST TERMINAL - 30023 PRESS-FIT MOUNT : hole dia. 1,44 mm (.057") 30003 PRESS-FIT MOUNT : hole dia. 1,55 mm (.061") SLEEVE = Bronze REF.no : 30023-XX A A =STANDARD PLATING CODE STANDARD TYPES ; (order no: 30023-30 STANDARD TYPES : (order no) 30003-90 REF.no : 30003-XX A MATERIALS : SLEEVE 10 = 0.25um Au 30 = 0.75um Au 90 = 5 um SnPb DIMENSIONS IN mm TOLERANCE ON : SLEEVE = brass LENGTHS : +/- 0.10 DIA. : + 0.07 / - 0.03 C2 47 GENERAL SPECIFICATIONS INTRODUCTION The DURTAL technology for pin receptacles with a stamped multi-finger contact spring press-fitted into a precision machined shell allows us to meet on optimal way almost all requirements given by the applications. With more than 20 different pre-tooled contacts, the standard range accepts pins from 0.3 to 2.6 mm. Depending on size and characteristics, the contacts are designed with 3, 4 or 6 fingers. The choice of heat treated beryllium-copper as contact material gives the best available mechanical performances with copper alloys, a continuous operating temperature range up to 150°C and optimal electrical characteristics. The sleeves and pins are manufactured by high speed turning process with additional secondary machining operation where flats, slots or solder cups are requested. The standard material choice is brass. Other alloy composition or hardness can be selected depending on application requirements, component size or type of termination. MATERIALS Standard materials for sleeves and pins: - Brass : - Bronze : CuZn36Pb3 resp. Alloy 360 per QQ-B-626 CuSn4Pb4Zn4 resp. Alloy 544 per QQ-B-750 Comp B Standard materials for contacts: - Beryllium Copper : Alloy 172 per QQ-C-533 PLATING Our plating facilities with the most performant automatic vibrating basket process are the best available ones, achieving more uniform and controlled finishes than conventional barrel plating. Standard platings: - Gold (Au) : flash to 5 microns to MIL-G-45204, Type I, Grade C - Silver (Ag) : 5 to 10 microns to QQ-S-365 Type III, Grade C - Tin-Lead (SnPb) : 5 microns bright, whisker free alloy 90/10 to MIL-P-81728 A - Nickel (Ni) : to QQ-N-290 DIMENSIONAL CHARACTERISTICS The preferred range to manufacture pins and receptacles with our high-speed turning technology lies between 1 and 4 mm. The minimal outer diameter for pin receptacles depends on the contact required by the size of the mating pin. These minimal values are given in the individual contact data on the following pages. MECHANICAL CHARACTERISTICS - Insertion characteristics: The diagram Fig. 1 shows the typical insertion forces plotted versus pin diameter for the standard contacts. This allows a first selection of the best suited contact for a given application. C2 48 GENERAL SPECIFICATIONS 2000 1000 900 800 700 600 500 INSERTION FORCE (g) 400 300 200 100 90 80 70 60 50 40 30 Fig. 1 2.60 2.40 2.20 2.00 1.80 1.60 1.40 1.20 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 20 PIN DIAMETER (mm) More detailed data are given in the individual contact data on pages 49 to 56. - Contact retention: This is the force needed to remove the press-fitted contact from its shell. Contact retention is greater than 40 N - Mechanical life: The mechanical life expectancy is dependent on the surface smoothness and diameter of the mating pin and on the platings; it reaches more than 1000 cycles. ELECTRICAL CHARACTERISTICS - Current ratings: see Fig. 2 The given values are for one receptacle / pin pair in free air and for 10°C temperature rise. All other electrical characteristics are dependent on the distance between contacts and the properties of insulator materials. ENVIRONMENTAL CHARACTERISTICS The products listed in this catalog are designed to meet the applicable general environmental requirements of: - IEC 68 : - IEC 512 : Basic environmental testing procedures Electromechanical components for electronic equipment; basic testing procedures and measuring methods C2 49 GENERAL SPECIFICATIONS - MIL-STD-202E : Test methods for electronic and electrical component part - MIL-STD-1344A : Test methods for electrical connectors CONTACT DATA The principal characteristics of standard contacts are listed in table Fig. 2 The contacts grouped together can be alternatively mounted in the same shells to get the required insertion characteristics. Group Part No Min pin diameter Max pin diameter A 11 12 22 30 25 20 32 31 14 06 16 47 18 34 02 27 23 39 13 07 08 0.35 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.52 0.56 0.56 0.63 0.94 0.81 1 1.05 1.15 1.28 1.2 1.65 2.1 0.53 0.53 0.56 0.63 0.63 0.66 0.66 0.66 0.80 0.82 0.86 0.95 1.1 1.2 1.27 1.32 1.65 1.64 1.65 2.1 2.6 B C D E F G H I J K Compliancy 0.08 0.08 0.13 0.13 0.13 0.23 0.23 0.23 0.1 0.18 0.15 0.28 0.08 0.25 0.15 0.13 0.2 0.2 0.25 0.3 0.28 Min pin length 2.1 1.6 1.6 2.1 2.1 2.1 2.1 2.1 1.7 2.9 2.2 2.2 1.6 3.1 2.2 2.2 2.5 2.6 3.2 3.8 3.1 Number of finger 3 4 6 4 4 4 6 6 6 4 6 6 6 4 6 6 6 6 4 4 6 Current rating (A) 3 3 3 3 3 3 3 3 4.5 4.5 4.5 4.5 8 8 8 8 11 11 11 15 18 Fig. 2 On the graphs on the following pages, all data are typical average values, measured with polished steel gauges: - Insertion force: The insertion force is represented by a shaded area because of the sizing effect. The upper line is the force measured at the first insertion, the lower line is the insertion force on the second cycle. - Normal force: Normal force is the force each finger exerts on the mating pin or component lead. - Compliancy: Compliancy is the ability of any contact to accept a broad range of pin size. The compliancy factor ( d ) specifies the resulting operating range after insertion of the largest permissible pin. To identify the contact mounted into the standard type receptacles presented in this catalog, read the first two digits of the group B = Insertion characteristics of the reference number. For example a receptacle with reference number ending with 3010 has the contact PN 30 mounted. C2 50 GENERAL SPECIFICATIONS CONTACT DATA FOR 0.35-0.53 DIAMETER PINS (d = 0.08) 3-FINGER, GROUP A CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 11 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.66 0.64 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 10 MATING PIN DIAMETER (mm) FOR 0.38-0.53 DIAMETER PINS (d = 0.08) 4-FINGER, GROUP B CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 12 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE 0.58 0.60 0.62 0.64 0.66 0.68 0.70 0.60 0.62 0.64 0.66 0.68 0.70 0.72 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 10 MATING PIN DIAMETER (mm) 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.58 0.56 0.54 0.52 0.50 0.40 0.38 0.36 0.34 0.32 0.30 0.28 10 0.48 MINIMUM 200 0.46 SHOULDER PREFERRED TO ASSIST ASSEMBLY 300 0.44 CONTACT PRESS-FIT INTO SHELL INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 0.42 FOR 0.38-0.56 DIAMETER PINS (d = 0.13) 6-FINGER, GROUP B 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 22 CONTACT MATING PIN DIAMETER (mm) C2 51 GENERAL SPECIFICATIONS CONTACT DATA FOR 0.38-0.63 DIAMETER PINS (d = 0.13) 4-FINGER, GROUP C CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 30 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.70 0.68 0.66 0.64 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 10 MATING PIN DIAMETER (mm) FOR 0.38-0.66 DIAMETER PINS (d = 0.23) 4-FINGER, GROUP C CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 20 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 20 d OPERATING RANGE 0.60 0.62 0.64 0.66 0.68 0.70 0.72 0.62 0.64 0.66 0.68 0.70 0.72 0.74 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 10 MATING PIN DIAMETER (mm) 100 90 80 70 60 50 40 30 20 d PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.60 0.58 0.56 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 10 0.54 MINIMUM 200 0.52 SHOULDER PREFERRED TO ASSIST ASSEMBLY 300 0.50 CONTACT PRESS-FIT INTO SHELL INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 0.48 FOR 0.38-0.66 DIAMETER PINS (d = 0.23) 6-FINGER, GROUP C 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 32 CONTACT MATING PIN DIAMETER (mm) C2 52 GENERAL SPECIFICATIONS CONTACT DATA FOR 0.38-0.66 DIAMETER PINS (d = 0.23) 6-FINGER, GROUP C CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 31 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 d 200 OPERATING RANGE 100 90 80 70 60 50 40 30 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 0.74 0.72 0.70 0.68 0.66 0.64 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 10 MATING PIN DIAMETER (mm) FOR 0.52-0.80 DIAMETER PINS (d = 0.10) 6-FINGER, GROUP D CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 14 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE 0.76 0.78 0.80 0.82 0.84 0.86 0.76 0.78 0.80 0.82 0.84 0.86 0.74 0.72 0.70 0.68 0.66 0.64 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 10 MATING PIN DIAMETER (mm) 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.74 0.72 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 10 0.70 MINIMUM 200 0.68 SHOULDER PREFERRED TO ASSIST ASSEMBLY 300 0.66 CONTACT PRESS-FIT INTO SHELL INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 0.64 FOR 0.56-0.82 DIAMETER PINS (d = 0.18) 4-FINGER, GROUP E 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 06 CONTACT MATING PIN DIAMETER (mm) C2 53 GENERAL SPECIFICATIONS CONTACT DATA FOR 0.56-0.86 DIAMETER PINS (d = 0.15) 6-FINGER, GROUP E CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 16 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 0.88 0.90 1.18 0.86 1.16 0.84 1.14 0.82 1.12 0.80 0.10 0.78 1.08 0.76 0.74 0.72 0.70 0.68 0.66 0.64 0.62 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 10 MATING PIN DIAMETER (mm) FOR 0.63-0.95 DIAMETER PINS (d = 0.28) 6-FINGER, GROUP E CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 47 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 10 MATING PIN DIAMETER (mm) 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 1.06 1.04 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 0.76 0.74 10 1.02 MINIMUM 200 1.00 SHOULDER PREFERRED TO ASSIST ASSEMBLY 300 0.98 CONTACT PRESS-FIT INTO SHELL INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 0.96 FOR 0.94-1.1 DIAMETER PINS (d = 0.08) 6-FINGER, GROUP F 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 18 CONTACT MATING PIN DIAMETER (mm) C2 54 GENERAL SPECIFICATIONS CONTACT DATA FOR 0.81-1.2 DIAMETER PINS (d = 0.25) 4-FINGER, GROUP G CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 34 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 0.75 0.70 10 MATING PIN DIAMETER (mm) FOR 1.-1.27 DIAMETER PINS (d = 0.15) 6-FINGER, GROUP H SHOULDER PREFERRED TO ASSIST ASSEMBLY CONTACT PRESS-FIT INTO SHELL MINIMUM PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 02 CONTACT INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE 1.22 1.24 1.26 1.28 1.30 1.32 1.28 1.30 1.32 1.34 1.36 1.38 1.20 1.18 1.16 1.14 1.12 1.10 1.08 1.06 1.04 1.02 1.00 0.98 0.96 0.94 0.92 0.90 0.88 10 MATING PIN DIAMETER (mm) 100 90 80 70 60 50 40 30 d 20 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) OPERATING RANGE 1.26 1.24 1.22 1.12 1.10 1.08 1.06 1.04 1.02 1.00 0.98 0.96 0.94 10 1.20 MINIMUM 200 1.18 SHOULDER PREFERRED TO ASSIST ASSEMBLY 300 1.16 CONTACT PRESS-FIT INTO SHELL INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 1.14 FOR 1.05-1.32 DIAMETER PINS (d = 0.13) 6-FINGER, GROUP H 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 27 CONTACT MATING PIN DIAMETER (mm) C2 55 GENERAL SPECIFICATIONS CONTACT DATA PN 23 CONTACT SHOULDER PREFERRED TO ASSIST ASSEMBLY CONTACT PRESS-FIT INTO SHELL MINIMUM INSERTION / WITHDRAWAL / NORMAL FORCE (grams) FOR 1.15-1.65 DIAMETER PINS (d = 0.20) 6-FINGER, GROUP I 1000 900 800 700 600 500 400 300 200 INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1.65 1.60 1.55 1.50 1.45 1.40 1.35 1.30 1.25 1.20 1.15 1.10 10 MATING PIN DIAMETER (mm) PN 39 CONTACT SHOULDER PREFERRED TO ASSIST ASSEMBLY CONTACT PRESS-FIT INTO SHELL MINIMUM INSERTION / WITHDRAWAL / NORMAL FORCE (grams) FOR 1.28-1.64 DIAMETER PINS (d = 0.20) 6-FINGER, GROUP I 1000 900 800 700 600 500 400 INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1.66 1.64 1.62 1.60 1.58 1.56 1.54 1.52 1.50 1.48 1.46 1.44 1.42 1.40 1.38 1.36 1.34 1.32 1.30 1.28 1.26 1.24 1.22 10 MATING PIN DIAMETER (mm) FOR 1.2-1.65 DIAMETER PINS (d = 0.25) 4-FINGER, GROUP I 300 200 100 90 80 70 60 50 40 30 d 20 OPERATING RANGE 1.65 1.60 1.55 1.50 1.45 1.40 1.35 1.30 10 1.25 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 1.20 MINIMUM INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 1.15 SHOULDER PREFERRED TO ASSIST ASSEMBLY CONTACT PRESS-FIT INTO SHELL 1000 900 800 700 600 500 400 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 13 CONTACT MATING PIN DIAMETER (mm) C2 56 GENERAL SPECIFICATIONS CONTACT DATA FOR 1.65-2.1 DIAMETER PINS (d = 0.3) 4-FINGER, GROUP J CONTACT PRESS-FIT INTO SHELL SHOULDER PREFERRED TO ASSIST ASSEMBLY MINIMUM INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 07 CONTACT 1000 900 800 700 600 500 400 INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 300 200 100 90 80 70 60 50 40 30 d 20 2.00 2.05 2.10 2.50 2.55 2.60 1.95 1.90 1.85 1.80 1.75 1.70 1.65 1.60 1.55 OPERATING RANGE PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 10 MATING PIN DIAMETER (mm) FOR 2.1-2.6 DIAMETER PINS (d = 0.28) 6-FINGER, GROUP K CONTACT PRESS-FIT INTO SHELL d 3000 OPERATING RANGE 2000 1000 900 800 700 600 500 400 300 200 2.45 2.40 2.35 2.30 2.25 2.20 2.15 100 PRECISION MACHINED SHELL (CUSTOM DESIGNS WELCOME) 2.10 MINIMUM INSERTION FORCE EFFECT OF SIZING BY MATING PIN WITHDRAWAL FORCE NORMAL FORCE 2.05 SHOULDER PREFERRED TO ASSIST ASSEMBLY 10000 9000 8000 7000 6000 5000 4000 INSERTION / WITHDRAWAL / NORMAL FORCE (grams) PN 08 CONTACT MATING PIN DIAMETER (mm) C2 NUMERICAL INDEX PART PAGE PART PAGE PART PAGE PART PAGE PART PAGE PART PAGE PART PAGE 00903 15 01321 24 01605 11 02101 44 04605 20 05111 38 15008 25 00904 15 01322 24 01606 11 02109 44 04606 20 05112 38 15009 25 01001 9 01323 23 01607 11 02201 30 04609 30 05113 36 15015 25 01005 9 01324 20 01608 11 02201 44 04610 19 05115 37 20011 31 01007 9 01401 8 01609 11 02209 44 04612 20 05116 38 30003 46 01008 9 01402 3 01610 11 02301 30 04613 20 05117 38 30023 46 01009 10 01404 4 01611 11 02301 44 04614 23 05118 37 50005 32 01016 9 01405 8 01612 11 02304 30 04615 23 05120 36 50006 32 01017 9 01406 7 01613 11 02309 44 05001 34 05121 38 50007 32 01101 11 01407 3 01702 13 02402 30 05002 34 05122 38 50008 32 01103 11 01408 3 01705 13 02502 18 05005 35 05123 38 50009 32 01105 11 01410 8 01707 28 02503 18 05006 33 05124 37 50015 41 01107 11 01411 7 01708 28 02504 18 05007 34 05201 44 50016 41 01108 10 01412 3 01709 28 02505 18 05008 33 05301 44 50019 32 01109 11 01414 8 01711 13 02601 31 05009 35 05501 41 50024 32 01110 11 01416 8 01714 13 02602 31 05010 35 05601 40 50026 41 01114 11 01417 7 01801 15 02603 31 05011 35 05602 40 50027 39 01115 10 01418 3 01802 15 02701 31 05012 34 06001 40 50037 39 01201 12 01420 8 01901 14 02702 31 05013 34 06201 45 50038 39 01202 12 01421 3 01903 14 02703 31 05014 35 06301 45 60006 29 01204 12 01423 3 01904 15 03003 32 05016 33 06302 45 60008 29 01205 12 01425 4 01905 15 03101 5 05017 33 07001 35 60009 29 01206 12 01426 8 01906 15 03102 21 05018 34 07201 45 60010 26 01303 22 01427 7 01907 16 03103 5 05019 32 07301 45 60011 26 01304 22 01428 4 01908 14 03204 41 05020 33 08001 40 60012 26 01305 22 01429 4 01909 14 03206 40 05023 35 08201 45 60014 29 01306 22 01430 4 01910 16 03207 41 05024 33 08301 45 60020 26 01308 10 01431 8 01911 16 03209 40 05101 38 08501 40 60021 26 01309 21 01501 13 01912 14 03301 32 05102 36 10005 6 60022 26 01313 25 01503 2 01913 16 03501 43 05103 38 10007 25 65002 27 01315 10 01505 2 01914 16 03502 43 05104 38 10008 6 65010 27 01316 24 01507 13 01915 17 03503 43 05105 38 10009 6 70004 43 01317 22 01601 11 01916 17 04401 44 05107 36 10011 6 75001 42 01318 24 01602 11 01917 17 04502 44 05108 38 10012 6 75010 42 01319 22 01603 11 01918 17 04602 19 05109 38 15000 21 01320 23 01604 11 02101 30 04603 19 05110 38 15007 25 C2