Ordering number : ENA1859B LA72914V Monolithic Linear IC FM Modulator and Demodulator IC http://onsemi.com Overview The LA72914V is a FM modulation and demodulation IC for audio signals. And it is possible to use that for the data pulse or the control pulse, etc. Functions • Alignment-free FM modulator and demodulator of 4.5MHz. • Alignment-free FM modulator and demodulator of 6.5MHz. • ALC/ FMAGC, Emphasis/ De-emphasis • Carrier frequency adjustment function, Standby switch Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Pd max Ta ≤ 70°C * Unit 7.0 V 300 mW Operating temperature Topr -20 to +70 °C Storage temperature Tstg -40 to +150 °C When mounted on a 114.3mm × 76.1mm × 1.6mm, glass epoxy. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Recommended Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Allowable operating voltage range Symbol VCC VCC op Semiconductor Components Industries, LLC, 2013 July, 2013 Conditions Ta=25°C Ta = -20 to +70°C Ratings Unit 5.0 V 4.7 to 5.5 V D0110 SY 20101118-S00005/N0410 SY/O2710 SY 20101008-S00006 No.A1859-1/9 LA72914V Electrical Characteristics at Ta = 25°C, VCC = 5V DC Characteristic Parameter Symbol Ratings Conditions min 2.4V regulator Current dissipation Control pin (6 pin) VREG Measure the DC voltage at pin 2 typ Unit max 2.2 2.4 2.6 V ICC1 Measure the current into pin 4 in normal mode. 26.0 33.0 40.0 mA ICC2 Measure the current into pin 4 in stand-by mode. 2.0 2.5 3.0 mA CNT6L Low level of input pin (6pin) in 4.5MHz TX mode. 0 0.4 V CNT6M Middle level of input pin (6pin) in stand-by mode. 2.0 3.0 V CNT6H High level of input pin (6pin) in 6.5MHz TX mode. 4.5 5.0 V AGCS Voltage of input pin (pin 11) in AGC stop 4.5 5.0 V 0 0.4 V Low level Control pin (6 pin) Middle level Control pin (6 pin) High level AGC stop at pin 11 control voltage TX OFF mode at pin 16 CNT16L Voltage of input pin (pin 16) in TX off mode control voltage Sound FM Modulation Block (TX) Parameter Symbol Conditions Ratings Unit FM carrier FFM1 Output frequency of T1B in no signals. T6=0.6V, T14:open min 4.455 output frequency FFM2 Output frequency of T1B in no signals. T6=4.2V, T14:open 6.435 6.500 6.565 MHz 1.9 2.3 2.6 Vp-p 1.3 1.7 2.1 Vp-p -30 -20 dB -30 -20 dB -60 -50 dB 20 25 30 kHz 7 12 17 kHz 0.45 0.5 0.55 Vp-p FM carrier output level VOFM1 Output level of T1B in no signals. typ 4.500 max 4.545 MHz Load impedance = 1kΩ T1-GND. T6=0.6V VOFM2 Output level of T1B in no signals. Load impedance = 1kΩ T1-GND. T6=4.2V FM carrier output second harmonics distortion 2HD1 2nd harmonics distortion of T1B in no signals. Load impedance = 1kΩ T1-GND. T6=0.6V 2HD2 2nd harmonics distortion of T1B in no signals. Load impedance = 1kΩ T1-GND. T6=4.2V FM carrier output mute level VFMT Output level of T1B in TX off mode. T6=0.6V (4.2V) FM deviation DEV Emphasis Characteristic FEMP FM deviation of T1A, T6=0.6V (4.2V), input at T16=1.0Vp-p/1kHz (sine) T16=200mVp-p, 1kHz (sine), M1=T1 output deviation. T16=200mVp-p, 5kHz (sine), M2=T1 output deviation. FEMP=M2-M1 ALC characteristic ALC1 T16A=0.25Vp-p, 1kHz (sine), T3:Open, T6=0.6V, T3 output level FM carrier “fo” adjustment (reference) ALC2 T16A=0.6Vp-p, 1kHz (sine), T3:Open, T6=0.6V, T3 output level 0.9 1.0 1.1 Vp-p ALC3 T16A=1.0Vp-p, 1kHz (sine), T3:Open, T6=0.6V, T3 output level 0.95 1.05 1.15 Vp-p FCNT1 No signal input. Measure T1B frequency. T16:Open, T6=0.6V (4.2V), T14=0.5V -0.22 MHz FCNT2 No signal input. Measure T1B frequency. T16:Open, T6=0.6V (4.2V), T14=4.5V +-.22 MHz Sound FM demodulation block (RX) Parameter Sound demodulation level Symbol VOUT1 Conditions Input signal: CAR=4.5MHz, DEV=±25kHz, MOD=1kHz, Ratings Unit min 0.6 typ 0.9 max 1.3 Vp-p 0.7 1.0 1.4 Vp-p Level: 100mVp-p. T5A input. Measure T9B signal level. (T9B-GND: ROUT=10kΩ) T6=4.2V VOUT2 Input signal: CAR=6.5MHz, DEV=±25kHz, MOD=1kHz, Level: 100mVp-p. T5A input. Measure T9B signal level. (T9B-GND: ROUT =10kΩ) T6=0.6V S/N SN1 Input signal: CAR=4.5MHz, No-modulation. Level: 100mVp-p. T5A input. T6=4.2V, (IHF-A) M1=T9B signal level. (T9B-GND: ROUT =10kΩ) SN1=20log(VOUT1/M1) 35 50 dB SN2 Input signal: CAR=6.5MHz, No-modulation. Level: 100mVp-p. T5A input. T6=0.6V, (IHF-A) M1=T9B signal level. (T9B-GND: ROUT =10kΩ) SN1=20log(VOUT2/M1) 35 50 dB Continued on next page No.A1859-2/9 LA72914V Continued from preceding page. Parameter Symbol THD THD1 Same condition VOUT1. Measure T9B signal. THD2 De-emphasis characteristic typ 0 0.3 max 1.0 Unit % 0 0.3 1.0 % Input signal: CAR=4.5MHz, DEV=±25kHz, MOD=5kHz, Level: 100mVp-p. T5A input. T6=4.2V, M1=T9B signal level. DEEM=20log(M1/VOUT1) -10 -7.5 -5 dB DEEM2 Input signal: CAR=6.5MHz, DEV=±25kHz, MOD=5kHz, Level: 100mVp-p. T5A input. T6=0.6V, M1=T9B signal level. DEEM=20log(M2/VOUT2) -10 -7.5 -5 dB FM AGC characteristic Same condition VOUT2. Measure T9B signal. Ratings min DEEM1 Trap-filter characteristic TRP1 T11=4.5V, T6=4.2V, T5A=4.5MHz, 100mVp-p. T12A=A1. T5A=6.5MHz. 100mVp-p. T12A=B1. TRP1=20log(B1/A1) -20 -15 dB TRP2 T11=4.5V, T6=0.6V, T5A=4.5MHz, 100mVp-p. T12A=A1. T5A=6.5MHz. 100mVp-p. T12A=B1. TRP2=20log(A1/B1) -20 -15 dB AGC1 T6=4.2V. T5A=4.5MHz, 300mVp-p. Measure T12 signal level. 250 350 450 mVp-p AGC2 T6=0.6V. T5A=6.5MHz, 300mVp-p. Measure T12 signal level. 250 350 450 mVp-p AGC3 T6=4.2V. T5A=4.5MHz, 30mVp-p. Measure T12 signal level. 200 300 400 mVp-p T6=0.6V. T5A=6.5MHz, 30mVp-p. Measure T12 signal level. 200 300 400 mVp-p 70 100 140 mVp-p 70 100 140 mVp-p AGC4 FM AGC STOP characteristic Conditions AGCSTP1 T6=4.2V. T11=4.5V, T5A=4.5MHZ, 100mVp-p. Measure T12 signal level. AGCSTP2 T6=0.6V. T11=4.5V, T5A=6.5MHz, 100mVp-p. Measure T12 signal level. FM input sensitivity FMIN1 Input signal: CAR=4.5MHz, DEV=±25kHz, MOD=1kHz, T6=4.2V. When T9B signal is OK, then measure T5A FM input level range. 30 100 300 mVp-p FMIN2 Input signal: CAR=6.5MHz, DEV=±25kHz, MOD=1kHz, T6=0.6V. When T9B signal is OK, then measure T5A FM input level range. 30 100 300 mVp-p Package Dimensions unit: mm (typ) 3178B 5.2 0.5 6.4 9 4.4 16 1 8 0.65 0.15 (1.3) 1.5max 0.22 0.1 (0.33) SANYO : SSOP16(225mil) No.A1859-3/9 LA72914V Pin Layout and Measurement circuit Sign: Highly accurate part use T1B T1 FM_out T2 T16 Audio_in /TX_CTL 16 1 FM_out VREG filter 2 (2.4V) Emphasis 3 filter Power supply (VCC) 5V 4 A ALC filter 15 T14 VCO_CTL 14 GND 13 VCC(5V) T5 T5A T6 T11 T7 Mode control 6 (TX,RX/STBY) AGC filter 11 De-emphasis T10 FM filter 10 De-emphasis 8 Audio_in Audio_out 9 T9B + GND T9 + De-emphasis filter 7 T8 FMAGC_OUT + MODE_CTL T12 FMAGC 12 monitor 5 FM_IN FM_IN AUDIO_IN + T3 T16A T15 Top view Block Diagram and Application Circuit VCO Auto tune ALC Filter FMAGC-OUT Monitor AGC Filter FM Filter 11 10 + 15 Bias 2.4V ALC (1.0Vp-p) 6dB AMP + 16 14 12 13 FMAGC 10k LPF VCO 4.5M/6.5M VREG 2.4V 1 2 FM-OUT (2Vp-p) Ripple Filter Phase Detector 6dB-AMP DRIVER Loop Filter VCO 6.5M/4.5M Offset Cancel Mode & Standby Control T4R6/STBY/T6R De-emphasis TRP 4.5M/6.5M 3 Emphasis Filter 5 4 6800pF FM-AMP DRIVER 9 FMAGC-DET Emphasis FMMOD Audio-OUT (1Vp-p) + TX control (High:TX-OFF /Low:TX-ON) Bias 2.4V 6 7 8 1000pF BPF VCC(5V) FM-IN (0.1Vp-p) State control T6R4:P-Up STBY:Open T4R6:P-Down De-emphasis Filter : Push-pull output No.A1859-4/9 LA72914V Pin Description Pin No. 1 Pin Name FM OUT Description Equivalent circuit 4.5MHz or 6.5MHz FM carrier output. Push-pull output pin. Output level is 2.5Vp-p (Load resistance=1kΩ) 1 2 2.4V REG Filter Internal regulator filter pin. Please connect 0.1μF (C1) 4V VCC 2 C1 3 Emphasis Filter Emphasis filter pin. Before FM modulation, make emphasis Characteristic at audio signal. C1(6800pF) Emphasis time constant must be matching de-emphasis time constant. (If you don’t need the emphasis, this pin is open.) 3 C1 4 VCC 5 FM IN VCC pin. Supply voltage is 5V DC. Please connect de-coupling capacitor. (about 47μF) FM signal input. Please use capacitor coupling. C1 SIG 5 2.4V 6 Mode CTL MODE control pin. Control modulation frequency TX=4.5MHz: 0 to 0.4V Stand-by: 2.0 to 3.0V TX=6.5MHz: 4.5V to VCC 6 Continued on next page. No.A1859-5/9 LA72914V Continued from preceding page. Pin No. 7 Pin Name De-emphasis Filter Description Equivalent circuit De-emphasis filter pin. De-emphasis time constant must be matching at emphasis time constant. Recommend value is 6800pF to 0.01μF. Connect Cap. Coupling to pin8. SIG 7 C1 8 RX Audio IN Internal DC bias is 2.4V. Please connect Cap. coupling. 8 C1 2.4V 9 Audio OUT Audio signal output pin. Push-pull output pin. Output level is 1.0Vp-p at 1kHz. (Load resistance=10kΩ) 9 10 FM Filter FM demodulator filter pin. Please connect 1.0μF capacitor. (If you need rising of low frequency gain, then change more large capacitor in use.) 10 11 AGC Filter FM AGC filter pin. AGC-DET Please connect 0.1μF capacitor. If you need reduce AGC-gain, then connect resistor (R1: 11pin-VCC) If FM AGC no need, please set pin11 voltage over 4.5V R1 DC voltage. 11 C1 Continued on next page. No.A1859-6/9 LA72914V Continued from preceding page. Pin No. 12 Pin Name AGC monitor Description Equivalent circuit FM AGC monitor pin. 12 13 GND 14 VCO CTL GND pin. Modulation frequency fine control pin. Adjustment frequency is, about ±220kHz at 0.5V to 4.5V DC. VR1 14 C1 2.4V 15 ALC CTL Audio ALC filter pin. Please connect 0.47μF capacitor. 15 C1 16 TX Audio IN Audio signal input pin. (TX-OFF_CTL) Internal bias is 2.4V DC. Please use capacitor coupling. If DC voltage set to under 0.4V DC, then modulator circuit stops. Demodulation circuit is work. This is receiving only mode. (TX-OFF: 0 to 0.4V) 16 C1 2.4V Signal processing outline [Modulation block] • Audio signal is input from pin16. (Internal bias is DC 2.4V.) Go through AMP (6dB)/ALC/LPF (10 kHz) and emphasis circuit, then input FM-modulation block. After FM-modulation block, go to output driver block then FM-audio signal output from pin1. • ALC: ALC circuit work at pin16 input level over than 0.5Vp-p. • LPF: LPF gain is -3dB at 10 kHz and -6dB/oct. Keep over modulation from emphasis characteristic. • Emphasis circuit: The pin3 owns an Emphasis characteristic which connected capacitor. Recommended value = 6800pF. • FM modulation: Carrier frequency is choosing from pin6 voltage. When pin16 input level is 0.5Vp-p, then FM deviation set to ±25 kHz. Internal LPF reduce harmonic spectrum. • Output Driver: Output AC voltage is about 2.0Vp-p. (Load resistance: 1kΩ) No.A1859-7/9 LA72914V [De-modulation block] • Demodulate audio signal from modulated audio signal. • FM-Audio signal is input from pin5. Go through 4.5M-Trap-filter or 6.5MHz-Trap-filter and AGC go to demodulator. After demodulator go to De-emphasis circuit. After de-emphasis circuit signal is output pin7. Pin7 signal is charge to DC bias for coupling capacitor at pin8. Audio signal from pin8 go to 6dB AMP then output from pin9. (Door-phone application, there are two FM carrier. In this case we recommend add BPF before pin5 FM-Audio signal input.) • 4.5M/6.5MHz-Trap-filter: Internal Trap-filter is change for pin6 mode control. (If modulator frequency is 4.5MHz, then internal Trap-filter is 4.5MHz.) • AGC: After AGC level is control about 0.3Vp-p. After AGC signal go to pin12 FM-monitor and de-modulator. • De-emphasis circuit: The pin7 owns an De-emphasis characteristic which connected capacitor. Recommended value = 10nF. • Output signal level: If input FM signal deviation is ±25 kHz, then output signal level is 1Vp-p (TYP) from pin9/ (Load resistance: 10kΩ at 1 kHz.) Characteristics ALC characteristics 600 FMAGC characteristics fo=4.5MHz (unmodulated signals) 500 2000 Output level, [mVp-p] Internal level of IC, [mVp-p] 2500 6dB 1500 Pin 9 1000 ALC 400 Pin 12 300 200 Pin 16 500 100 0 0 0 200 400 600 800 1000 1200 Input level, [mVp-p] 3 1 10 100 1000 10000 Input level, [mVp-p] Frequency responce TxIn-RxOut Output level, [dB] 0 -3 -6 -9 -12 -15 0.01 0.1 1 10 100 Frequency, [kHz] No.A1859-8/9 LA72914V Application example WIRE BPF 4.5MHz BPF 6.5MHz RX 4.5MHz MIC LA72914V (pin6:High) RX 6.5MHz LPF 6.5MHz TX 6.5MHz LPF 4.5MHz TX 4.5MHz LA72914V (pin6:Low) MIC [Above-mentioned recommendation BPF] Made by Murata Mfg.: SFSKA4M50DF00 (4.5MHz)/SFSKA6M50CF00 (6.5MHz) ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A1859-9/9