Revision - ON Semiconductor

MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOIC−16
CASE 751BA
ISSUE A
DATE 18 MAY 2015
SCALE 1:1
0.10 C D
NOTES 4&5
45 5 CHAMFER
NOTE 6
D
A
16
2X
9
0.10 C D
E
E1
NOTES 4&5
L2
2X
0.20 C D
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION.
H
ALLOWABLE PROTRUSION SHALL BE 0.004 mm IN EXCESS OF
MAXIMUM MATERIAL CONDITION.
4. DIMENSION D DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS
OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS
SHALL NOT EXCEED 0.006 mm PER SIDE. DIMENSION E1 DOES
NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD
FLASH OR PROTRUSION SHALL NOT EXCEED 0.010 mm PER SIDE.
5. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOT­
TOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE OUTER­
SEATING MOST EXTREMES OF THE PLASTIC BODY AT DATUM H.
L
C PLANE
6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM H.
DETAIL A
7. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 TO 0.25 FROM THE LEAD TIP.
8. A1 IS DEFINED AS THE VERTICAL DISTANCE FROM THE SEATING
PLANE TO THE LOWEST POINT ON THE PACKAGE BODY.
h
D
1
8
B
16X b
NOTE 6
0.25
TOP VIEW
C A-B D
M
NOTES 3&7
DETAIL A
A2
NOTE 7
0.10 C
A
e
A1
C
SIDE VIEW
NOTE 8
c
END VIEW
SEATING
PLANE
RECOMMENDED
SOLDERING FOOTPRINT*
DIM
A
A1
A2
b
c
D
E
E1
e
h
L
L2
MILLIMETERS
MIN
MAX
--1.75
0.10
0.25
1.25
--0.31
0.51
0.10
0.25
9.90 BSC
6.00 BSC
3.90 BSC
1.27 BSC
0.25
0.41
0.40
1.27
0.25 BSC
GENERIC
MARKING DIAGRAM*
16X
0.76
16
XXXXXXXXXX
AWLYWWG
16X
1.52
1
7.00
XXXXX
A
WL
Y
WW
G
1
1.27
PITCH
DIMENSIONS: MILLIMETERS
*This information is generic. Please refer
to device data sheet for actual part
marking. Pb−Free indicator, “G”, may
or not be present.
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DOCUMENT NUMBER:
STATUS:
98AON34919E
ON SEMICONDUCTOR STANDARD
REFERENCE:
© Semiconductor Components Industries, LLC, 2002
October, DESCRIPTION:
2002 − Rev. 0
SOIC−16
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
http://onsemi.com
1
Electronic versions are uncontrolled except when
accessed directly from the Document Repository. Printed
versions are uncontrolled except when stamped
“CONTROLLED COPY” in red.
Case Outline Number:
PAGE 1 OFXXX
2
DOCUMENT NUMBER:
98AON34919E
PAGE 2 OF 2
ISSUE
REVISION
DATE
O
RELEASED FOR PRODUCTION FROM POD #6000209 TO ON SEMICONDUCTOR.
REQ. BY B. BERGMAN.
19 SEP 2008
A
REDREW DRAWING TO JEDEC STANDARDS AND ADDED SOLDER FOOTPRINT.
REQ. BY F. KOLANKO.
18 MAY 2015
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
© Semiconductor Components Industries, LLC, 2015
May, 2015 − Rev. A
Case Outline Number:
751BA