Data Sheet PT8A263 PIR Alarm Controller ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Features Description • Low standby current • PT8A263 is a fully integrated mixed-signal CMOS LSI 2 stage op-amp for filtering • On-chip oscillator chip designed for the low cost applications of PIR • On-chip voltage regulator • 4 different operation modes selected by SEL1 & SEL2 • Low battery detector • Built-in noise rejection circuit • LED output indicating warm-up period, low battery and PIR trigger signal • 2 outputs to drive external devices such as speech ICs, high pitch piezo buzzer or door bell ICs • Lead free DIP-16 and SOIC-16 package (passive Infrared) alarm control system. The analog front-end is based on PTI’s proven PIR controller IC (PT8A261). The multipurpose alarm IC can be widely used in a variety of applications ranging from household security, portable alarm to toys. PT8A263 is also equipped with op-amps for filtering, a comparator, timer, low battery detector, control circuit, voltage regulator and oscillator. Application Ordering Information • Low cost security system sensor components • Motion sensor to drive low cost speech chip for Ordering No. PT8A263PE PT8A263WE PT8A263DE alarm alert • Motion detect alarm with high pitch buzzer alert • Door chime applications with external door bell Package Lead free 16-pin DIP Lead free 16-pin SOIC Die form ICs Block Diagram OP2O OP2N _ OP2P + OP1N Noise rejection circuit Voltage divider OP1O OP1P Comparator + _ SEL1 SEL2 OUT1 Control circuit Regulator OUT2 LED VEE GND Low Battery Detector OSC Mode control circuit VCC RST System oscillator PT0084 (09/08) Ver:5 1 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Pin Information Pin Configuration 1 16 OP2O LED 2 15 OP2N OSC 3 14 OP2P GND 13 OP1O OUT1 4 OUT2 5 SEL1 6 11 OP1P SEL2 7 10 RST VCC 8 9 VEE PT8A263 12 OP1N Pin Description Name GND Pin No. 1 Type Ground LED 2 O OSC 3 I 4, 5 O Outputs to drive external devices 6, 7 O Operating mode selection 8 Power VEE 9 O RST 10 I OP1P 11 I OP1N OP1O 12 13 I O OP2P 14 I OP3N OP2O 15 16 I O OUT1, OUT2 SEL1, SEL2 VCC Description Ground LED output: indicates PIR trigger signal. It is an active high signal with 125Hz pulse in normal mode. Input of oscillator: external resistor or capacitor changeable, resistor pull up, capacitor pull down, 16kHz for normal application Power supply Internal voltage regulator output: 3.6V with respect to ground. Connected to the drain of PIR sensor Chip reset input: active low, kept floating or connected an RC network Non-inverted input of first operational amplifier: connected directly to source of PIR sensor Inverted input of first operational amplifier Output of first operational amplifier Non-inverted input of second operational amplifier, 1.8V internally, 2.2uF capacitor pull down Inverted input of second operational amplifier Output of second operational amplifier PT0084 (09/08) Ver:5 2 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Pad Location 1470um Die No. SEL1 OUT2 OUT1 OSC LED SEL2 1710um GND VCC OP2O VCC OP2N NC OP2P VEE RST OPIP OPIN OPIO Pad Coordinate Pad Name X Coordinate GND 570 LED 570 OSC 570 OUT1 570 OUT2 -378.8 SEL1 -30.1 SEL2 570 VCC -197.1 VCC 136.9 Note: Substrate is connected to GND Y Coordinate Pad Name X Coordinate Y Coordinate 65.4 -101.6 399.4 232.4 689.2 -687.2 -435.6 -687.2 -687.2 NC VEE 570 -570 303.9 -44.8 -211.8 -570 -570 -570 -570 -268.6 232.4 -687.2 689.2 689.2 -435.6 -268.6 -101.6 65.4 RST OP1P OP1N OP1O OP2P OP2N OP2O PT0084 (09/08) Ver:5 3 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Functional Description • Low Battery Detection Internal low Battery Detector indicates voltage value of VCC less than a contain value which is about 3.8V. A The PIR sensor detects infrared power variations induced by the motion of a human body and converts it to voltage variations. This input voltage is fed into PT8A263 for signal processing. Bandpass filtering is first accomplished by a 2-stage op-amp, followed by the peak and valley voltages comparisons. If the input signal is larger than the specified peak voltage or smaller than the specified valley voltage for a certain period of time, this PIR trigger signal will be produced to the internal noise rejection circuit in which a valid trigger is qualified based on some criteria. The output signals will then be generated to drive external devices according to different mode of operations. • • Low Battery alarm indication can be given at LED pin when the division voltage is less than VEE/2. At the same time the system will be halt. Most of the internal circuits are hung up except oscillator and LED indication circuit. • RST RST is used to reset the chip. It is internal pull-high and active low. The use of CRST can extend the power-on initial time. If the RST pin is an open circuit (without CRST), the initial time is the default (40 seconds). VEE VEE supplies power to the analog front-end circuit with a stabilized voltage that is 3.6V with respect to GND normally. • Power On Initial The PIR signal amplifier requires a warm up period after power-on. The input should be disabled during this period. OSC OSC is an I/O pin of internal oscillator. System frequency of 16KHz can be generated when connected to an external RC. • Operational Mode The operation modes of PT8A263 are shown in the following table. Mode of Operation/2 SEL1 SEL2 Functions Normal Alarm: OUT1 = low (active) for 5 seconds after the first trigger. OUT2 goes low for 5 seconds after the 2nd trigger. LED does not latch trigger status. OUT2 (low active) will not trigger if there is no PIR signal 12 1 1 seconds after the first trigger. Normal Alarm with Delay: OUT1 goes low after first triggered, if the second trigger signal comes after 15 seconds, OUT2 keep high, if the second trigger signal comes after 12 seconds but less than 15 seconds, OUT2 0 1 will goes low for 5 seconds. LED is latched on until power down or reset the chip. Siren Alarm: Complimentary drive high pitch piezo buzzer. Center frequency = 1kHz (options for 500Hz and 2kHz). 2 stages of alarm: First trigger: Output is 1/4 sec on, 4 sec off. If no 2nd trigger within 12 sec, all outputs are 1 0 reset, no sound. 2nd trigger: Output is 1/4 sec on, 2 sec off for 30 sec. After 30 sec, output = 1 sec on, 1/2 sec off, continue for 5 minutes. After that, the chip enters stop mode. LED is latched on after 2nd trigger, until power down or chip reset. Door Chime mode: Once trigger occurs, OUT1 is active (high) for 1 sec, OUT2 is active (high) for another 1 0 0 sec after OUT1 is asserted. LED has no latch function. PT0084 (09/08) Ver:5 4 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Timing Diagram PIR Signal Trigger and Output Signals for Door Chime Mode RST TRI_EN 40s w arm-up time Comparator input <32ms Comparator output >32ms >160ms <2s (1) >288ms (2) (3) Valid trigger SEL2,SEL1 00 00 00 = Door Chime mode OUT1 1s OUT2 00 1s 1s LED 125Hz pulse Notes: The PIR trigger signal is qualified to be a valid PIR trigger signal if it conforms to one of the following criteria : 1. More then 3 triggers (each > 32ms) detected within 2s, 2. Two triggers detected within 2s (1 trigger > 160ms and another > 32ms), 3. One trigger (> 288ms) detected. Output Signals for Normal Alarm Mode RST 40s warm-up time trig_en_b >12s >5s&<12s Valid trigger SEL2,SEL1 11 11 11 5s OUT1 11 = Normal Alarm mode 5s 5s OUT2 LED 125Hz pulse PT0084 (09/08) Ver:5 5 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Output Signals for Normal Alarm with Delay Mode RST 40s warm-up time 40s warm-up time trig_en_b >12s&<15s >15s Valid trigger SEL2,SEL1 01 01 01 = Normal Alarm with Delay Mode 01 5s OUT1 5s 5s OUT2 LED 125Hz pulse Output Signals for Siren Alarm Mode RST 40s warm-up time trig_en_b >4.25s&<12s Valid trigger SEL2,SEL1 10 10 10 1s 0.25s OUT 2 10 = Siren Alarm Mode 2s 0.5s 30s 5min OUT 1 LED 125Hz pulse Output w ith 1KHz central frequency Low Battery Detection Operation Low Battery threthold voltage RST VC C system status system running system halts system halts 1s LED 125Hz pulse PT0084 (09/08) Ver:5 6 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Maximum Ratings Storage Temperature......................................................................................-40oC to +125oC Ambient Temperature with Power applied.................................................-20oC to +85oC Supply Voltage to Ground Potential (Inputs & VCC Only)........................-0.5V to+6.0V Supply Voltage to Ground Potential (Outputs & D/O Only)....................-0.5V to+6.0V DC Input Voltage ................................................................................................-0.5V to +6.0V DC Output Current...................................................................... 20mA Power Dissipation.............................................................................................................500mW Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended operation conditions Sym Parameter Min Typ Max Unit VCC VIH VIL fSYS TA Supply Voltage Input HIGH Voltage Input LOW Voltage System Oscillator Frequency Operating temperature 4.75 0.8 VCC 12.8 -25 5.0 16 - 6.0 0.2VCC 19.2 70 V V V kHz °C DC Electrical Characteristics Sym Description Test Conditions Min Typ Input high level current - SEL1 and SEL2 -1 IIH VIH = 4.5V Input high level current - RST -1 Input high level current - OSC 400 Input low level current - SEL1, SEL2, OSC -1 IIL VIL = 0.5V Input low level current - OSC -10 IOH Output Source Current (OUT1, OUT2) VOH = 4.5V -6 -12 IOL Output Sink Current (OUT1, OUT2) VOL = 0.5V 15 55 VTH OSCS Transfer High Voltage 2.0 2.3 VTL OSCS Transfer Low Voltage 1.0 1.2 Note: These specifications apply for VCC = 5.0V and -25OC £ TA £ 70OC, unless otherwise specified. Max 1 -10 550 1 -20 2.8 1.6 Units µA µA µA µA µA mA mA V V AC Electrical Characteristics Voltage Regulator Sym Description VEE Output Voltage OP2P Noninverting input of OP2 Line Regulation ∆Vo Load Regulation ∆VLDR IL Maximum Current Test Conditions No load No load 4.5V ≤ VCC ≤ 5.5V, IL = 1mA Cfilter= 4.7uF (between VEE pin and GND pin) VCC = 5V, 0.5mA ≤ IL ≤ 2mA Cfilter= 4.7uF (between VEE pin and GND pin) VCC = 5V Min 3.4 1.6 -4 Typ 3.6 1.8 1.0 10 - Max 3.8 2.0 50 100 - Units V V mV mV mA Operational Amplifier and Window Comparator Sym UGBW VTH VTL Description Unit Gain B and width Test Conditions VCC = 5V VCC = 5V Windows Comparator Threshold Min 10 1.9 1.4 Typ 2.05 1.55 Max 2.2 1.7 Units kHz V V Min 12.8 52 Typ 16 62.5 Max 19.2 78 Units kHz µs Oscillator Sym fOSCS TOSCS Description Oscillator Frequency Oscillator period Test Conditions VCC = 5V, RS=560kΩ, CS=200p - PT0084 (09/08) Ver:5 7 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Power Dissipation Sym Description Min Typ Max Units Power Supply Current Test Conditions VCC = 5V, fOSCS=16kHz RS=560kΩ, CS=200p, Input Pins=GND, all output pins floating ICC - 80 100 µA ICCQ Quiescent Supply Current VCC = 5V, Input Pins=GND, all output pins floating - 70 - µA Low Battery Detector Sym VLBTH Description Low Battery Detector Threshold Voltage Test Conditions VCC = 5V Min 3.50 Typ 3.80 Max 4.01 Units V Application Circuit Siren Alarm Mode R1 1M VCC D1 16 GND OP2O LED OP2N OSC OP2P OUT1 OP1O OUT2 OP1N 12 6 SEL1 OP1P 11 R8 10k 7 SEL2 RST 10 VCC 8 R5 560K R7 1K C4 200P VCC 1 2 3 4 BZ1 BUZZER 5 BAT 1 6V VCC 15 14 C5 C2 203 C9 10UF/16V 22UF/16V R4 22K 13 C3 203 VCC 9 VEE C7 100UF/16V PT8A263 C8 100UF/16V R2 1M R6 D S G 56K C1 203 R3 22K C6 22UF/16V SD6222 Door Chime Mode R1 1M VCC D1 R5 560K C4 200P 1 R7 2 1K 3 OUT 1 4 Toexternal OUT 2 door bell IC 5 6 7 VCC BAT 1 6V 8 C7 100UF/16V GND OP2O LED OP2N 16 15 14 OSC OP2P OUT1 OP1O OUT2 OP1N SEL1 OP1P 11 SEL2 RST 10 VCC VEE C2 203 C9 10UF/16V C5 22UF/16V R4 22K 13 C3 203 12 9 PT8A263 C8 100UF/16V VCC R6 56K D S G C1 203 R2 1M R3 22K C6 22UF/16V SD62 22 PT0084 (09/08) Ver:5 8 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Mechanical Information PE (Lead free DIP-16) 16 .240 .280 1 6.09 7.11 7.62 8.25 .300 .325 .780 .800 19.82 20.32 .210 Max .008 .014 5.33 SEATING PLANE .015 .115 .150 2.921 3.81 0.381 .014 .022 2.54 10.92 .356 .558 1 DENOTES DIMENSIONS IN MILLIMETERS Note: 1) Controlling dimensions in inches. 2) Ref: JEDEC MS-001 AB WE (Lead free SOIC-16) 16 .0099 .0196 .149 .157 .430 Max Min X.XX X.XX .100 typical 0.20 0.35 3.78 3.99 0.25 0.50 x 45° .0075 .0098 0-8° 0.19 0.25 0.41 .016 1.27 .050 .386 .393 9.80 10.00 .2284 .2440 5.80 6.20 .053 1.35 .068 1.75 .0155 .0260 0.393 0.660 SEATING PLANE REF .050 BSC 1.27 .013 .020 0.330 0.508 .0040 0.10 .0098 0.25 X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS Note: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012 AC PT0084 (09/08) Ver:5 9 Data Sheet PT8A3263-66A-F/67A/68A NTC Heating Controller with Multi LEDs ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Notes Email: [email protected] Web Site: www.pti.com.cn, www.pti-ic.com China: No. 20 Building, 3/F, 481 Guiping Road, Shanghai, 200233, China Tel: (86)-21-6485 0576 Fax: (86)-21-6485 2181 Asia Pacific: Unit 1517, 15/F, Chevalier Commercial Centre, 8 Wang Hoi Rd, Kowloon Bay, Hongkong Tel: (852)-2243 3660 Fax: (852)- 2243 3667 U.S.A.: 3545 North First Street, San Jose, California 95134, USA Tel: (1)-408-435 0800 Fax: (1)-408-435 1100 Pericom Technology Incorporation reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom Technology does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom Technology product. The company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom Technology Incorporation. PT0084 (09/08) Ver:5 10