USER MANUAL NI SMD-7613/7614/7615/7616 This manual contains information about the configuration and use of the National Instruments SMD-7613, SMD-7614, SMD-7615, and SMD-7616. They are referred to inclusively in this manual as the NI SMD-761x. Note This manual is not applicable for NI SMD-7610/7611/7612 devices. Refer to to the unique documentation for information related to the NI SMD-7610/7611/7612. Functionality on these devices are roughly equivalent. The NI SMD-7613/7615 operates from 18 to 53 VDC, and has a running current of up to 5 A per phase. The SMD-7614/7616 operates from 18 to 88 VDC, and runs current up to 10 A per phase. The SMD-7615/7616 features encoder feedback. Contents Safety Information .................................................................................................................... 2 Block Diagram.......................................................................................................................... 3 Getting Started.......................................................................................................................... 3 Mounting the Drive .................................................................................................................. 4 Connecting the Power Supply .................................................................................................. 4 Choosing a Power Supply......................................................................................................... 5 Voltage.............................................................................................................................. 5 Current .............................................................................................................................. 5 Regeneration..................................................................................................................... 7 Connecting the Drive Using Ethernet....................................................................................... 7 Motor Wiring Recommendations ............................................................................................. 12 Four Lead Motors ............................................................................................................. 13 Six Lead Motors ............................................................................................................... 13 Eight Lead Motors ............................................................................................................ 14 Connecting Input Signals.......................................................................................................... 15 STEP and DIR Inputs ....................................................................................................... 17 Single Ended Inputs.......................................................................................................... 19 Connecting Limit Switches and Sensors .......................................................................... 21 Analog Inputs ................................................................................................................... 22 Connecting an Encoder (SMD-7615/7616) .............................................................................. 23 Programmable Outputs ............................................................................................................. 25 Configuring the Drive............................................................................................................... 28 Motor ................................................................................................................................ 28 Control .............................................................................................................................. 29 I/O Configuration ............................................................................................................. 31 Self Test............................................................................................................................ 31 Torque Speed Curves................................................................................................................ 32 Motor Heating........................................................................................................................... 38 Drive Heating............................................................................................................................ 47 Mechanical Outline................................................................................................................... 48 Technical Specifications ........................................................................................................... 48 Alarm Codes ............................................................................................................................. 50 Safety Information Only qualified personnel are permitted to transport, assemble, commission, and maintain this equipment. Properly qualified personnel are persons who are familiar with the transport, assembly, installation, commissioning and operation of motors, and who have the appropriate qualifications for their jobs. The qualified personnel must know and observe the following standards and regulations: • IEC 364 resp. CENELEC HD 384 or DIN VDE 0100 • IEC report 664 or DIN VDE 0110 • National regulations for safety and accident prevention or VBG 4 To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. • Read all available documentation before assembly and commissioning. Incorrect handling of products in this manual can result in injury and damage to persons and machinery. Strictly adhere to the technical information on the installation requirements. • It is vital to ensure that all system components are connected to earth ground. Electrical safety is impossible without a low-resistance earth connection. • The SMD-761x contains electrostatically sensitive components that can be damaged by incorrect handling. Discharge yourself before touching the product. Avoid contact with high insulating materials (artificial fabrics, plastic film, etc.). Place the product on a conductive surface. • During operation keep all covers and cabinet doors shut. Otherwise, there are deadly hazards that could possibility cause severe damage to health or the product. • In operation, depending on the degree of enclosure protection, the product can have bare components that are live or have hot surfaces. Control and power cables can carry a high voltage even when the motor is not rotating. • Never pull out or plug in the product while the system is live. There is a danger of electric arcing and danger to persons and contacts. 2 | ni.com | NI SMD-7613/7614/7615/7616 User Manual • After powering down the product, wait at least ten minutes before touching live sections of the equipment or undoing connections (e.g., contacts, screwed connections). Capacitors can store dangerous voltages for long periods of time after power has been switched off. To be safe, measure the contact points with a meter before touching. Be alert to the potential for personal injury. Follow the recommended precautions and safe operating practices. Safety notices in this manual provide important information. Read and be familiar with these instructions before attempting installation, operation, or maintenance. The purpose of this section is to alert users to possible safety hazards associated with this equipment and the precautions that need to be taken to reduce the risk of personal injury and damage to the equipment. Failure to observe these precautions could result in serious bodily injury, damage to the equipment, or operational difficulty. Block Diagram Figure 1. NI SMD-761x Block Diagram External Power Supply 7613/7615: 24-48 VDC 7614/7616: 24-80 VDC Internal Logic Supply INPUT X1 INPUT X2 Status INPUT X3 INPUT X4 INPUT X5 INPUT X6 X7/CWLIM MOSFET PWM Power Amplifier Optical Isolation Motor X8/CCWLIM OUTPUT Y1 OUTPUT Y2 Encoder OUTPUT Y3 DSP OUTPUT Y4 7615/7616 Only ANALOG IN1 Ethernet ANALOG IN2 Getting Started You need the following to use your NI SMD-761x stepper drive: a 24 to 48 VDC power supply (80 V max for NI SMD-7614/7616). Refer to Choosing a Power Supply for help in choosing the right power supply one of the recommended motors NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 3 a small flat blade screwdriver for tightening the connectors a source of step signals, such as a PLC or motion controller The connectors and other points of interest are illustrated below. These are detailed later in the manual. Figure 2 shows an overview of the connectors on the NI SMD-7613/7614/7615/7616 stepper drive. Figure 2. NI SMD-7613/7614/7615/7616 Stepper Drive Connectors 2 3 4 5 6 7 1 1 2 3 4 Chassis Grounding Screw Motor and Power Supply Connector Encoder Feedback (SMD-7615/7616) Input and Output Signals 5 6 7 Ethernet Connector Drive Status LEDs Rotary Switch Mounting the Drive You can mount your drive on the wide or the narrow side of the chassis using #6 screws. If possible, the drive should be securely fastened to a smooth, flat metal surface that will help conduct heat away from the chassis. If this is not possible, then forced airflow from a fan may be required to prevent the drive from overheating. Refer to Drive Heating for more information. • Never use your drive in a space where there is no air flow or where other devices cause the surrounding air to be more than 50 °C. • Never put the drive where it can get wet or where metal or other electrically conductive particles can get on the circuitry. • Always provide air flow around the drive. When mounting multiple drives near each other, maintain at least one half inch of space between drives. Connecting the Power Supply If you need information about choosing a power supply, refer to Choosing a Power Supply. • Connect the power supply “+” terminal to the connector terminal labeled “V+”. • Connect power supply “-” to the connector terminal labeled “V-”. • The green ground screw on the corner of the chassis should be connected to earth ground. • Use 18 or 20 gauge wire. 4 | ni.com | NI SMD-7613/7614/7615/7616 User Manual The NI SMD-761x drives contain an internal fuse that connects to the power supply + terminal. This fuse is not user replaceable. If you want to install a user serviceable fuse in your system, install a fast acting, 7 A fuse in line with the + power supply lead. Caution Do not reverse the wires. Reverse connection will destroy your drive and void your warranty. If you plan to use a regulated power supply you may encounter a problem with regeneration. If you rapidly decelerate a load from a high speed, much of the kinetic energy of that load is transferred back to the power supply. This can trip the overvoltage protection of a switching power supply, causing it to shut down. NI offers the SMD-7700 regeneration clamp to solve this problem. If in doubt, buy an SMD-7700 for your first installation. If the regen LED on the SMD-7700 never flashes, you don’t need the clamp. Choosing a Power Supply When choosing a power supply, there are many things to consider. If you are manufacturing equipment that will be sold to others, you probably want a supply with all the safety agency approvals. If size and weight are an issue, get a switching supply. And you must decide what size of power supply (in terms of voltage and current) is needed for your application. National Instruments offers two power supplies that are excellent matches for the NI SMD-761x drives: PS-12 24V, 6.3A) and PS-13 (48V, 6.7A). Voltage The motor can provide more torque at higher speeds if a higher power supply voltage is used. Refer to the Torque Speed Curves section for guidance. If you choose an unregulated power supply, make sure the no load voltage of the supply does not exceed the drive’s maximum input voltage specification. Current The maximum supply current you could ever need is two times the motor current. However, you will generally need a lot less than that, depending on the motor type, voltage, speed and load conditions. That’s because the NI SMD-761x uses a switching amplifier, converting a high voltage and low current into lower voltage and higher current. The more the power supply voltage exceeds the motor voltage, the less current you’ll need from the power supply. A motor running from a 48 volt supply can be expected to draw only half the supply current that it would with a 24 volt supply. We recommend the following selection procedure: 1. If you plan to use only a few drives, get a power supply with at least twice per phase current rating of the step motor. Example: for a motor that’s rated for 2 A/phase use a 4 A power supply. NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 5 2. If you are designing for mass production and must minimize cost, get one power supply with more than twice the rated current of the motor. Install the motor in the application and monitor the current coming out of the power supply and into the drive at various motor loads. This will tell you how much current you really need so you can design in a lower cost power supply. Tables 1 lists the relevant specifications for suggested motors. Please consider this information when choosing a power supply. Table 1. NI SMD-7613/7615 Power Supply Current Holding Torque 6 Motor oz-in kg-cm Drive Current Setting (A) ST11-1 7.0 0.50 1.2 1.4 1.4 8 ST11-2 15.0 1.08 1.2 2.0 2.6 18 ST14-1 26.0 1.87 1.2 4.3 5.5 20 ST17-1 31.4 2.26 1.6 2.1 2.8 35 ST17-2 51.0 3.67 2.0 1.7 3.6 54 ST17-3 62.8 4.52 2.0 1.7 3.0 68 ST23-1 76.6 5.52 3.4 0.7 1.4 120 ST23-4 177 12.7 5.0 0.4 1.2 300 ST23-6 264 19.0 5.0 0.5 1.6 480 ST23-8 354 25.48 6.0 0.5 2.2 750 ST24-1 123.2 8.87 3.36 0.73 1.6 260 ST24-2 177 12.74 4.8 0.43 1.1 450 ST24-3 354 24.48 4.8 0.65 2.4 900 ST34-2 650 46.8 10.0 0.19 1.3 1400 ST34-5 1200 86.4 9.7 0.27 2.2 2680 ST34-8 1845 133 10.0 0.27 2.4 4000 ST34-1 396.5 28.55 7.56 0.24 1.7 1100 ST34-4 849.6 61.18 7.56 0.33 2.7 1850 ST34-7 1260 90.75 6.72 0.63 5.4 2750 | ni.com | Resistance (Ω) Inductance (mH) Rotor Inertia (g-cm2) NI SMD-7613/7614/7615/7616 User Manual Regeneration When a motor rapidly decelerates from high speed under load, the kinetic energy may be reconverted into electrical energy and transferred back to the power supply. When using regulated power supplies, this can trip the overvoltage protection and lead to a shutdown, or cause damage to the system. Unregulated power supplies do not typically have overvoltage protection, and may store regenerated energy in capacitors. Connecting the Drive Using Ethernet The drive requires only a CAT5 Ethernet cable connection to connect to your PC. You can connect the drive directly to your PC’s network card, to an auxiliary network card in your PC, or to a router or network switch. 1. Physically connect the device to your network (or directly to the PC). 2. Set the drive IP address. 3. Set the appropriate networking properties on your PC. NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 7 Your device includes a 16 position rotary switch for setting its IP address. The factory default address for each switch setting is shown in the table below. Table 2. IP Address Rotary Switch Settings Position IP Address 0 10.10.10.10 1 192.168.1.10 2 192.168.1.20 3 192.168.1.30 4 192.168.0.40 5 192.168.0.50 6 192.168.0.60 7 192.168.0.70 8 192.168.0.80 9 192.168.0.90 A 192.168.0.100 B 192.168.0.110 C 192.168.0.120 D 192.168.0.130 E 192.168.0.140 F DHCP The IP address corresponding to positions 1 through E can be changed using the NI Stepper Configuration Utility software. Setting 0 is always 10.10.10.10, the universal recovery address. Setting F is DHCP, which commands the device to get an IP address from a DHCP server on the network. The IP address automatically assigned by the DHCP server may be dynamic or static depending on how the administrator has configured DHCP. The DHCP setting is reserved for advanced users. Your PC, or any other equipment that you use to communicate with the device, will also have a unique address. On the device switch settings 1 through E use the standard class B subnet mask (i.e., 255.255.0.0). The mask for the universal recovery address is the standard class A (i.e., 255.0.0.0). 8 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Option 1: Connect a Drive to Your LAN If you have a spare port on a switch or router and if you are able to set your device to an IP address that is compatible with your network, and not used by anything else, this is a simple way to get connected. This technique also allows you to connect multiple devices to your PC. If you are on a corporate network, check with your system administrator before connecting anything new to the network. He or she should be able assign you a suitable address and help you get going. Figure 3. Example Network Configuration NIC LAN Switch or Router PC Drive Many networks use dynamic addressing where a DHCP server assigns addresses on demand. The address you choose for your device might get assigned to something else by the DHCP server at another time. Once you’ve chosen an appropriate IP address for your device, set the rotary switch according to the address table above. If none of the default addresses are acceptable for your network, you can enter a new table of IP addresses using the NI Stepper Configuration Utility. If your network uses addresses starting with 192.168.0, the most common subnet, you will want to choose an address from switch settings 4 through E. Another common subnet is 192.168.1. If your network uses addresses in this range, the compatible default selections are 1, 2 and 3. If your PC address is not in one of the above private subnets, you will have to change your subnet mask to 255.255.0.0 in order to communicate with your device. To change your subnet mask: 1. 2. Open Network Connections. a. Windows 8.1/8/7/Vista—Open Control Panel. From the icon view, open Network and Sharing Center, then click Change Adapter Settings. b. Windows XP—Right-click My Network Places and select Properties. Right-click your network interface card (NIC) and select Properties. a. b. Windows 8.1/8/7/Vista—Scroll down and select (TCP/IPv4), then click Properties. Windows XP—Scroll down and select Internet Properties (TCP/IP), then click Properties. 3. 4. If the Obtain an IP address automatically option is selected, your PC is getting an IP address and a subnet mask from the DHCP server. Cancel this dialog and proceed to the Using DHCP section. If the option Use the following IP address is selected, change the subnet mask to 255.255.0.0 and click OK. NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 9 Using DHCP If you want to use your device on a network where all or most of the devices use dynamic IP addresses supplied by a DHCP server, set the rotary switch to “F”. When the device is connected to the network and powered on, it will obtain an IP address and a subnet mask from the server that is compatible with your PC. However, you will not know what address the server assigns to the device. The NI Stepper Configuration Utility can find your device using the Drive Discovery feature, as long as your network isn’t too large. When the device connected to the network is powered on, select Drive Discovery from the Drive menu to launch the Network Interface Dialog dialog box. Figure 4. Network Interface Dialog Box Normally, Drive Discovery only detects one network interface card (NIC), and selects it automatically. If you are using a laptop and have both wireless and wired network connections, a second NIC may appear. Please select the NIC that you use to connect to the network to which you’ve connected your device. Then click OK. Drive Discovery notifies you as soon as it has detected a device. If you think this is the correct device, click Yes. If you are not sure, click Not Sure and Drive Discovery will look for additional devices on you network. Once you have told Drive Discovery which device is yours, it automatically enters the device IP address in the IP address text box so that you are ready to communicate. Option 2: Connect a device Directly to Your PC 1. Connect one end of a CAT5 Ethernet cable into the LAN card (NIC) on your PC and the other into the device. You don’t need a special crossover cable; the device automatically detects the direct connection and make the necessary physical layer changes. 2. Set the IP address on the device to 10.10.10.10 by setting the rotary switch to position 0. 3. To set the IP address of your PC: 10 | a. Windows 8.1/8/7/Vista—Open Control Panel. From the icon view, open Network and Sharing Center, then click Change Adapter Settings. b. Windows XP—Right-click My Network Places and select Properties. ni.com | NI SMD-7613/7614/7615/7616 User Manual 4. Right-click your network interface card (NIC) and select Properties. a. b. Windows 8.1/8/7/Vista—Scroll down and select (TCP/IPv4), then click Properties. Windows XP—Scroll down and select Internet Properties (TCP/IP), then click Properties. 5. Select Use the following IP address and enter the address 10.10.10.11. This assigns your PC an IP address that is on the same subnet as the device. Windows directs any traffic intended for the device’s IP address to this interface card. 6. Next, enter the subnet mask as 255.255.255.0. 7. Leave Default gateway blank. This prevents your PC from looking for a router on this subnet. Note Because you are connected directly to the device, anytime the device is not powered you will receive a small message bubble in the corner of your screen saying “The network cable is unplugged.” Option 3: Use Two Network Interface Cards (NICs) This technique allows you to keep your PC connected to your LAN, but keeps the device off the LAN, preventing possible IP conflicts or excessive traffic. 1. If you use a desktop PC and have a spare card slot, install a second NIC and connect it directly to the device using a CAT5 cable. You don’t need a special “crossover cable”; the device will automatically detect the direct connection and make the necessary physical layer changes. 2. If you use a laptop and only connect to your LAN using wireless networking, you can use the built-in RJ45 Ethernet connection as your second NIC. 3. Set the IP address on the device to 10.10.10.10 by setting the rotary switch to position 0. 4. To set the IP address of your PC: 5. a. Windows 8.1/8/7/Vista—Open Control Panel. From the icon view, open Network and Sharing Center, then click Change Adapter Settings. b. Windows XP—Right-click My Network Places and select Properties. Right-click your network interface card (NIC) and select Properties. a. b. Windows 8.1/8/7/Vista—Scroll down and select (TCP/IPv4), then click Properties. Windows XP—Scroll down and select Internet Properties (TCP/IP), then click Properties. 6. Select Use the following IP address and enter the address 10.10.10.11. This assigns your PC an IP address that is on the same subnet as the device. Windows directs any traffic intended for the device’s IP address to this interface card. 7. Next, enter the subnet mask as 255.255.255.0. 8. Leave Default gateway blank. This prevents your PC from looking for a router on this subnet. Note Because you are connected directly to the device, anytime the device is not powered you will receive a small message bubble in the corner of your screen saying “The network cable is unplugged.” NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 11 Motor Wiring Recommendations This section explains how to connect motors to the NI SMD-761x. Refer to your motor documentation for any special considerations that may affect your configuration. Maintain at least 2 in. separation between the power supply cable and input lines or encoder feedback. All power supply cables should be properly shielded, and the shield grounded at the power supply. Signal cables should be shielded, and grounded as close as possible to the signal source. Caution Never connect or disconnect the motor while the system is powered on. Ensure any shield or grounding strap on the motor is connected to the chassis ground screw located near the motor/power connector. Note Figure 5. Motor/Power Connector Figure 6. Grounding Screw on the Chassis 12 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Four Lead Motors Four lead motors can only be configured according to the following diagram. Note Motor wire colors are correct for NI stepper motors compatible with the NI SMD-761x. These wire colors may not match a third-party stepper motor. Phase A+ Phase A– Red Blue Figure 7. Four Lead Motor Connection Yellow Phase B+ White Phase B– Six Lead Motors Six lead motors can be connected in series or center tap. A series connected motor produces more torque but it will not be able to run as fast as a motor in center tap configuration. In series operation, the motor should be operated at 30% less than the rated current to prevent overheating. Refer to the wiring diagrams below to connect a six lead motor. Phase A– Grn/Wht No connect White Green Phase A+ Figure 8. Six Lead Motor Connected in Series Red/Wht Phase B+ Black No connect Red Phase B– NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 13 Phase A+ Phase A– Grn/Wht Green White No connect Figure 9. Six Lead Motor Connected in Center Tap Red/Wht No connect Black Phase B+ Red Phase B– Eight Lead Motors Eight lead motors can be connected in series or parallel. A series connected motor needs less current than one that is connected in parallel but it will not be able to run as fast. In series operation, the motor should be operated at 30% less than the rated current to prevent overheating. Refer to the wiring diagrams below to connect an eight lead motor. Black Phase A– Org/Wht Blk/Wht Orange Phase A+ Figure 10. Eight Lead Motor Connected in Series Red Phase B+ Red/Wht Yel/Wht Yellow 14 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Phase B– Black Blk/Wht Org/Wht Orange Phase A– Phase A+ Figure 11. Eight Lead Motor Connected in Parallel Red Red/Wht Yel/Wht Phase B+ Phase B– Yellow Connecting Input Signals The NI SMD-761x has three types of input: • High speed digital inputs for step and direction commands/encoder following. 5 V logic. • Digital inputs for other signals. 12 to 24 V logic. • Analog inputs are reserved for furture use. Note All inputs except STEP and DIR use 12 to 24 VDC logic. All drives include eight digital inputs and two analog inputs: • CW & CCW Limit: Optional input that can be used to inhibit motion in a given direction, forcing the motor and load to travel within mechanical limits. It can be configured for active closed or active open. • IN1/STEP & IN2/DIR: Digital signals that can be used for commanding position. Quadrature signals from encoders can also be used. These inputs can also be connected to sensors and switches. • IN3, IN4, IN5, IN6: Software-prgrammable inputs that can be used for motor enable, alarm reset, or jogging. These inputs can also be connected to sensors and switches. • Analog In: Analog signals that can command velocity or position. Can be configured for 0 to 10 V, 0 to 5 V, ±10 V, or ±5 V, with or without an offset. NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 15 Figure 12. Input Connector Pin Diagram X8/CCWLIMIT– X8CCWLIMIT+ X7/CWLIMIT– X7/CWLIMIT+ Y4– Y4+ GND +5V OUT Y COMMON Y3/FAULT Y2/MOTION Y1/BRAKE 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 GND X1/STEP+ X1/STEP– X2/DIR+ X2/DIR– X COMMON X3/ENABLE X4/ALARM RESET X5/CWJOG X6/CCWJOG ANALOG IN2 ANALOG IN1 Figure 13. ISelect Internal Circuitry of the I/O Connector 8 XCOM 7 X3/EN 6 x4/RST 2200Ω 2200Ω 2200Ω 5 X5 2200Ω 4 X6 22 X7/CWLIM+ 23 X7/CWLIM– 24 X8/CCWLIM+ 25 X8/CCWLIM- 16 | ni.com | 2200Ω 2200Ω NI SMD-7613/7614/7615/7616 User Manual STEP and DIR Inputs The drive includes two high speed inputs called STEP and DIR. They accept 5 volt single-ended or differential signals, up to 2 MHz. Normally these inputs connect to an external controller that provides step & direction command signals. You can also connect a master encoder to the inputs for following applications. The following section demonstrates example signal connections. Refer to Motor Wiring Recommendations for cable instructions. Figure 14. Connecting to Indexer with Sourcing Outputs Indexer with Sourcing Outputs +5V OUT X2/DIR– DIR X2/DIR+ IN/OUT 1 X1/STEP– STEP X1/STEP+ Figure 15. Connecting to Indexer with Sinking Outputs Indexer with Sinking Outputs +5V OUT X2/DIR+ DIR X2/DIR– IN/OUT 1 X1/STEP+ STEP X1/STEP– Figure 16. Connecting to Indexer with Differential Outputs Indexer with Differential Outputs DIR+ X2/DIR+ DIR– X2/DIR– STEP+ X1/STEP+ STEP- X1/STEP– IN/OUT 1 NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 17 Figure 17. Connecting for Encoder Following Indexer with Differential Outputs A+ X1/STEP+ A– X1/STEP– B+ X2/DIR+ B- X2/DIR– GND GND IN/OUT 1 Using 12 to 24 Volt Signals Most PLC’s don’t use 5 V signals. Use external dropping resistors to connect signals up to 24 V to the STEP and DIR inputs. For 12 V logic, use 820 Ω, 1/4 W resistors. For 24 V logic, use 2200 Ω, 1/4 W resistors. Caution Do not exceed an input voltage of 24 VDC. Never apply AC power to an input terminal. Connect the resistors according to the following diagrams: Figure 18. Connecting to PLC with Sourcing (PNP) Outputs +12-24V OUT1 PLC with Sourcing Outputs 18 | ni.com | X2/DIR+ X1/STEP– OUT2 X1/STEP+ GND X2/DIR– NI SMD-7613/7614/7615/7616 User Manual 761x Figure 19. Connecting to PLC with Sinking (NPN) Outputs +12-24V X2/DIR+ DIR X2/DIR– PLC with Sinking Outputs 761x X1/STEP+ STEP X1/STEP– Figure 20. Using Mechanical Switches at 24 Volts + X2/DIR+ X2/DIR– Direction Switch +24 VDC Power Supply Drive X1/STEP+ – X1/STEP– Run/Stop Switch (closed=run) Single Ended Inputs The SMD-761x includes four single ended, optically isolated input circuits that can be used with sourcing or sinking signals. These inputs can be used with PLCs, sensors, relays, or mechanical switches. These inputs require an external power supply. COM, or common, refers to a connection to a common voltage. This is often ground, but not always.If using sourcing (PNP) signals, connect COM to the negative terminal of the power supply. When using sinking (NPN) signals, connect COM to the positive terminal of the power supply. Note Refer to the following diagrams for examples of how to connect the drive to commonly used devices: NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 19 Figure 21. Connecting to Input Switch or Relay + XCOM 12-24 VDC Power Supply Drive - X3..X6 Switch or Relay (closed = logic low) Figure 22. Connecting Multiple Drives 12-24 VDC Power Supply + – OUT+ XCOM IN/OUT1 Drive OUT– X3..X6 Figure 23. Connecting an NPN Type Proximity Sensor to an Input + XCOM + NPN Proximity Sensor - 12-24 VDC Power Supply Output - 20 | ni.com | NI SMD-7613/7614/7615/7616 User Manual X3..X6 Drive Figure 24. Connecting a PNP Type Proximity Sensor to an Input + + PNP Proximity Sensor - 12-24 VDC Power Supply - Output X3..X6 Drive XCOM Connecting Limit Switches and Sensors The CWLIMIT and CCWLIMIT differential inputs can be used to connect end of travel sensors. You can use signals that are sinking (NPN), sourcing (PNP) or differential (line driver). By connecting switches or sensors that are triggered by the motion of the motor or load, you can force the motor to operate within certain limits, preventing damage to your system by traveling too far. The limit inputs are optically isolated, allowing you to choose a voltage for your limit circuits of 12 to 24 VDC. This also allows you to have long wires on limit sensors that may be far from the drive with less risk of introducing noise to the drive electronics. Refer to the following diagrams for help connecting limit switches and sensors: Figure 25. Wiring a Mechanical Limit Switch + CWLIMIT+ CCWLIMIT+ 12-24 VDC Power Supply CCWLIMIT– – Drive CCWLIMIT– NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 21 Figure 26. Wiring a Sinking Output Limit Sensor + CW LIMIT+ + Limit Sensor – DC Power Supply Output Drive CW LIMIT– – Figure 27. Wiring a Sourcing Output Proximity Sensor + + Proximity Sensor - DC Power Supply Output - CW LIMIT+ Drive CW LIMT– Analog Inputs The device features two analog inputs. Each input can accept a signal range of 0-VDC, ±5 VDC, 0 to 10 VDC or ±10 VDC. The drive can be configured to operate at a speed or position that is proportional to the analog signal. The following figure represents the internal circuitry of the analog inputs: Figure 28. Internal Circuitry of Analog Inputs 1 AIN1 Signal Conditioning AIN2 Signal Conditioning 2 13 GND Caution 22 | ni.com | Always use a shielded cable to maintain signal integrity. NI SMD-7613/7614/7615/7616 User Manual Us the NI Stepper Configuration Utility to configure settins such as signal range, offset, deadband, and filter frequency. The following diagram depicts the connection of a potentiometer to the analog input, which could be used to control the commanded position or velocity. Figure 29. Potentiometer Connected to Analog Input 1 CW 1-10 kW pot CCW 18 +5V OUT 1 AIN 13 GND 2 AIN2 Drive Connecting an Encoder (SMD-7615/7616) The encoder connections use a HD-15 connector, which you must connect to your encoder as shown below. If your encoder is single ended, connect the encoder outputs to the A+, B+ and Z+ inputs. Leave A-, B- and Z- unconnected. (Z is the encoder index signal and is optional.) Figure 30. Encoder Connection Pin Numbering 5 15 1 6 Table 3. Encoder Connection Pin Definition Pin Function 1 Encoder A+ 2 Encoder A- 3 Encoder B+ 4 Encoder B- 5 Encoder Z+ 6 Encoder Z- 7 +5 VDC, 200 mA NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 23 Table 3. Encoder Connection Pin Definition (Continued) Pin Function 8 GND 9 No Connect 10 No Connect 11 No Connect 12 No Connect 13 No Connect 14 No Connect 15 Shield The internal circuitry of the encoder connection is depicted below: 5 KΩ 5K Ω 12.5 KΩ 7 5 KΩ 12.5 KΩ 12.5 KΩ Figure 31. Encoder Connection Pin Numbering +5V 1 A+ 2 A– 3 B+ 4 B– 5 Z+ 6 8.3 KΩ 8.3 KΩ 8.3 KΩ Z– 8 GND 24 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Programmable Outputs The drive features four digital outputs. These outputs can be set to automically control a motor brake, to signal a fault condition, to indicate when the motor is moving, or to provide an output frequency proportional to motor speed (tach signal). Refer to the diagram below for a representation of the internal cirtucitry of the digital outputs: Figure 32. Potentiometer Connected to Analog Input 1 14 Y1 17 YCOM 16 Y3 15 Y2 20 Y4+ 21 Y4– The outputs can be used to drive LEDs, relays, and the inputs of other electronic devices like PLCs and counters. For Y4, the “+” (collector) and “-” (emitter) terminals of each transistor are available at the connector. This allows you to configure this output for current sourcing or sinking. The Y1 to 3 outputs can only sink current. The Y COM terminal must be tied to power supply (-). NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 25 Diagrams of each type of connection follow. Caution Do not connect outputs to more than 30 VDC. Caution The current through an output terminal must not exceed 100 mA. Figure 33. Sinking Output Using Y1, Y2, or Y3 + Y1/2/3 Load 5-24 VDC Power Supply IN/OUT1 – YCOM Figure 34. Sinking Output Using Y4 + Y4 + Load 5-24 VDC Power Supply IN/OUT1 – Y4 – Figure 35. Sourcing Output Using Y1, Y2, or Y3 5-24 VDC Power Supply + – PLC COM IN/OUT1 Y1/2/3 YCOM 26 | ni.com | NI SMD-7613/7614/7615/7616 User Manual IN Figure 36. Sourcing Output Using Y4 5-24 VDC Power Supply – + COM IN/OUT1 PLC Y4+ IN Y4– Figure 37. Driving a Relay Using Y1, Y2, or Y3 Relay 5-24 VDC Power Supply + Y1/2/3 IN/OUT1 1N4935 suppression diode – YCOM Figure 38. Driving a Relay Using Y4 Relay + 5-24 VDC Power Supply Y4+ IN/OUT1 1N4935 suppression diode – Y4– NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 27 Configuring the Drive The drive is configured in software with the NI Stepper Configuration Utility, available at ni.com/downloads. When you have located your device with the utility, you can configure various aspects of the motor performance and control for your application. Motor From the NI Stepper Configuration Utility home screen, click the Motor icon to open the configuration window. Figure 39. NI Stepper Configuration Utility Configuration Window The drive works best with the specially matched motors selectable from the Standard Motor list. Select the motor you will use and configure the following settings: Running Current Seting the Running Current to 100% will achieve maximum torque. However, under some conditions you might want to reduce the current to save power or lower motor temperature. This is important if the motor is not mounted to a surface that will help it conduct heat away or if you expect the ambient temperature to be high. Step motors produce torque in direct proportion to current, but the amount of heat generated is roughly proportional to the square of the current. If you operate the motor at 90% of rated current, the motor provides 90% of the rated torque and approximately 81% as much heat. At 70% current, the torque is reduced to 70% and the heating to about 50%. 28 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Idle Current/Idle Current Delay You can reduce motor heating and power consumption by lowering the motor current when it is not moving. The drive automatically lowers the motor current when it is idle for longer than the time specified by Idle Current Delay. The default 50% idle current setting lowers the holding torque to 50% of the specified Running Current, which is enough to prevent the load from moving in most applications. You can adjust this value to account for your load and heating requirements. Load Inertia The drive includes anti-resonance and electronic damping features which greatly improve motor performance. To perform optimally, the drive must understand the electromechanical characteristics of the motor and load. Most of this is completed automatically in the factory during motor and drive assembly. To further enhance performance, you must specify the innertia of the load. If you are unsure of this value, you can experimentally find an acceptable value by entering a multiplier of the rotor inertia. Control From the NI Stepper Configuration Utility home screen, click the Motion icon to open the Motion Control Mode Window. Select the Pulse & Direction Mode button to configure the following settings: Figure 40. NI Stepper Configuration Utility Configuration Window Steps/Rev You can configure the number of steps per revolution to match the details of your application. A higher value provides smoother motion, though you may want to configure this value to match the phsyical parameters of the system such as gearing or screw pitch. Step Smoothing Filter At lower step resolutions such as 200 steps per revolution (full step) and 400 steps per revolution (half step) motors produce more audible noise than when they are microstepped (2000 steps per revolution and beyond). The drive includes a feature called microstep emulation, also called step smoothing, that can provide smooth motion when using full and half steps. If the Steps/Rev NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 29 setting is 2000 or higher, this feature is not needed and can be set to the highest possible value, 2500. The step smoothing process uses a command filter which causes a slight delay, or lag in the motion. The following figure shows an example of the delay that can occur from using the step smoothing filter. Figure 41. Delay Due to Filtering Input Noise Filter Electrical noise can negatively affect the STEP signal by causing the drive to interpret one step pulse as two or more pulses. This results in extra motion and inaccurate motor and load positioning. To solve this problem, the drive includes a digital noise filter on the STEP and DIR inputs. The default factory setting of this filter is 7.5 MHz, which is suitable for most applications. Your maximum pulse rate equals the highest motor speed multiplied by the number of steps per revolution. For example: revs steps 40 ------------------ × 20, 000 ------------- = 800kHz sec ond revs Consider the maximum pulse rate when deciding whether you must increase the filter frequency. 30 | ni.com | NI SMD-7613/7614/7615/7616 User Manual I/O Configuration From the NI Stepper Configuration Utility home screen, click the I/O icon to open the Motion I/O Configuration window to configure the following settings: Figure 42. NI Stepper Configuration Utility Configuration Window Fault Output The fault output will be triggered if there is a fault condition. This may be a fault within the drive or a system fault. Not all faults will cause the drive to be disabled. If you are running the NI Stepper Configuration Utility while an alarm condition develops, a dialog box will give you details of the fault. Alarms and faults are also displayed by a pattern of red and green flashes on the drive's front panel LED. Refer to the Alarm Code section for code definitions. Alarm Reset Input This parameter allows you to configure an input to reset any alarms that result from a fault. If this is not enabled, you must reset alarms by cycling power to the drive. Brake Output If your motor features a brake, you can configure an output to release the brake when the motor is enabled. You can configure the delay settings to ensure the brake is fully applied before disabling the motor. Motor Enable Input The Motor Enable input toggles the power stage of the drive. This allows the drive to be powered on while the motor is inactive. Self Test If you are having trouble getting your motor to turn, use the built-in self test from the NI Stepper Configuration Utility home page. Select the Drive menu item and choose Self Test. Use this feature to confirm that the motor is wired correctly, selected, and otherwise operational. NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 31 Torque Speed Curves Figure 43. SMD-761x Torque Curve for ST11 & ST14, 24 V Power Supply ST11, ST14 24 VDC power supply, 20000 steps/rev 25 ST14-1 (1.2 A/phase) ST11-2 (1.2 A/phase) ST11-1 (1.2 A/phase) 20 oz-in 15 10 5 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 44. SMD-761x Torque Curve for ST17, 24 V Power Supply ST17 24 VDC power supply, 20000 steps/rev, all motors connected in parallel 100 ST17-3 (2.0 A/phase) 90 ST17-2 (2.0 A/phase) ST17-1 (1.6 A/phase) 80 70 oz-in 60 50 40 30 20 10 0 0 5 10 15 20 rev/sec 32 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 25 30 35 40 Figure 45. SMD-761x Torque Curve for ST17, 48 V Power Supply ST17 48 VDC power supply, 20000 steps/rev, all motors connected in parallel 100 ST17-3 (2.0 A/phase) 90 ST17-2 (2.0 A/phase) ST17-1 (1.6 A/phase) 80 70 oz-in 60 50 40 30 20 10 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 46. SMD-761x Torque Curve for ST23, 24V Power Supply ST23 24 VDC power supply, 20000 steps/rev, all motors connected in parallel 350 300 ST23-8 - (6.0 A/phase) ST23-6 (5.0 A/phase) ST23-4 - (5.0 A/phase) ST23-1 (3.4 A/phase) 250 oz-in 200 150 100 50 0 0 5 10 15 20 25 30 35 40 rev/sec NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 33 Figure 47. SMD-761x Torque Curve for ST23, 48 V Power Supply ST23 48 VDC power supply, 20000 steps/rev, all motors connected in parallel 350 300 ST23-8 (6.0 A/phase) ST23-6 (5.0 A/phase) ST23-4 (5.0 A/phase) ST23-1 (3.4 A/phase) 250 oz-in 200 150 100 50 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 48. SMD-761x Torque Curve for ST24, 24V Power Supply ST24 24 VDC power supply, 20000 steps/rev 350 ST24-3 (4.8 A/phase) ST24-2 (4.8 A/phase) 300 ST24-1 (3.36 A/phase) 250 oz-in 200 150 100 50 0 0 5 10 15 20 rev/sec 34 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 25 30 35 40 Figure 49. SMD-761x Torque Curve for ST24, 48V Power Supply ST24 48 VDC power supply, 20000 steps/rev 350 ST24-3 (4.8 A/phase) 300 ST24-1 (3.36 A/phase) ST24-2 (4.8 A/phase) 250 oz-in 200 150 100 50 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 50. SMD-7614/7616 Torque Curve for ST34-2/5/8, 48V Power Supply ST34-2/5/8 with SMD-7614/7616 24 VDC power supply, 20000 steps/rev, all motors connected in parallel 1400 ST34-8 (10 A/phase) ST34-5 (9.7 A/phase) 1200 ST34-2 (10 A/phase) 1000 oz-in 800 600 400 200 0 0 5 10 15 20 25 30 35 40 rev/sec NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 35 Figure 51. SMD-7614/7616 Torque Curve for ST34-2/5/8, 48V Power Supply ST34-2/5/8 with SMD-7614/7616 48 VDC power supply, 20000 steps/rev, all motors connected in parallel 1400 ST34-8 (10 A/phase) ST34-5 (9.7 A/phase) 1200 ST34-2 (10 A/phase) 1000 oz-in 800 600 400 200 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 52. SMD-7614/7616 Torque Curve for ST34-2/5/8, 80V Power Supply ST34-2/5/8 with SMD-7614/7616 80 VDC power supply, 20000 steps/rev, all motors connected in parallel 1400 ST34-8 (10 A/phase) 1200 ST34-2 (10 A/phase) ST34-5 (9.7 A/phase) 1000 oz-in 800 600 400 200 0 0 5 10 15 20 rev/sec 36 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 25 30 35 40 Figure 53. SMD-7614/7616 Torque Curve for ST34-1/4/7, 24V Power Supply ST34-1/4/7 with SMD-7614/7616 24 VDC power supply, 20000 steps/rev, all motors connected in parallel 1000 ST34-7 (6.72 A/phase) 900 ST34-4 (7.56 A/phase) ST34-1 (7.56 A/phase) 800 700 oz-in 600 500 400 300 200 100 0 0 5 10 15 20 25 30 35 40 rev/sec Figure 54. SMD-7614/7616 Torque Curve for ST34-1/4/7, 48V Power Supply ST34-1/4/7 with SMD-7614/7616 48 VDC power supply, 20000 steps/rev, all motors connected in parallel 1000 ST34-7 (6.72 A/phase) 900 ST34-4 (7.56 A/phase) ST34-1 (7.56 A/phase) 800 700 oz-in 600 500 400 300 200 100 0 0 5 10 15 20 25 30 35 40 rev/sec NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 37 Figure 55. SMD-7614/7616 Torque Curve for ST34-1/4/7, 60V Power Supply ST34-1/4/7 with SMD-7614/7616 60 VDC power supply, 20000 steps/rev, all motors connected in parallel 1000 ST34-7 (6.72 A/phase) 900 ST34-4 (7.56 A/phase) ST34-1 (7.56 A/phase) 800 700 oz-in 600 500 400 300 200 100 0 0 5 10 15 20 25 30 35 40 rev/sec Motor Heating Step motors convert electrical power from the driver into mechanical power to move a load. Because step motors are not perfectly efficient, some of the electrical power turns into heat on its way through the motor. This heating is not so much dependent on the load being driven but rather the motor speed and power supply voltage. There are certain combinations of speed and voltage at which a motor cannot be continuously operated without damage. The following table and figures show the maximum duty cycle versus speed for each motor at commonly used power supply voltages. Please refer to this information when planning your application. A step motor typically reaches maximum temperature after 30 to 45 minutes of operation. If you run the motor for one minute then let it sit idle for one minute, that is a 50% duty cycle. Five minutes on and five minutes off is also 50% duty. However, one hour on and one hour off has the effect of 100% duty because during the first hour the motor will reach full (and possibly excessive) temperature. The actual temperature of the motor depends on how much heat is conducted, convected, or radiated out of it. Our measurements were made in a 40 °C (104 °F) environment with the motor mounted to an aluminum plate sized to provide a surface area consistent with the motor power dissipation. Your results may vary. 38 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Table 4. SMD-761x Maximum Motor Duty Cycle Max Duty Cycle at 40 °C Drive Current (A), peak of sine 24 VDC ST11-1 1.2 100% ST11-2 1.2 100% ST14-1 1.2 See chart ST17-1 1.6 100% See chart ST17-2 2.0 100% See chart ST17-3 2.0 100% See chart ST23-1 3.4 100% See chart ST23-4 5.0 See chart See chart ST23-6 5.0 See chart See chart ST34-2 10.0 See chart See chart ST34-5 9.7 See chart See chart ST34-8 10.0 See chart See chart Motor 48 VDC Figure 56. Duty Cycle for the ST17-1 with the SMD-761x, 24 VDC ST14-1 Max Duty Cycle vs Speed 24 VDC, 1.2A, 40°C Ambient Mounted on 4.75" x 4.75" x .25" Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 39 Figure 57. Duty Cycle for the ST17-1 with the SMD-761x, 48 VDC ST17-1 Max Duty cycle vs Speed 48 VDC, 1.60 Amps 40°C Ambient on 4.75 x 4.75 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) Figure 58. Duty Cycle for the ST17-2 with the SMD-761x, 48 VDC ST17-2 Max Duty cycle vs Speed 48 VDC, 2.0 Amps 40°C Ambient on 4.75 x 4.75 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 40 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 30 40 50 Figure 59. Duty Cycle for the ST17-3 with the SMD-761x, 48 VDC ST17-2 Max Duty cycle vs Speed 48 VDC, 2.0 Amps 40°C Ambient on 4.75 x 4.75 x .25 Aluminum Plate % Duty Cycle 100 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) Figure 60. Duty Cycle for the ST23-1 with the SMD-761x, 48 VDC ST23-1 Max Duty Cycle vs Speed 48 VDC, 3.4 Amps, 40°C Ambient on 6.4 x 6.4 x .25 Aluminum Plate % Duty Cycle 100 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 41 Figure 61. Duty Cycle for the ST23-4 with the SMD-761x, 24 VDC ST23-4 Max Duty cycle vs Speed 24VDC, 5.0A, 40°C Ambient on 6.4 x 6.4 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) Figure 62. Duty Cycle for the ST23-4 with the SMD-761x, 48 VDC ST23-4 Max Duty cycle vs Speed 48VDC, 5.0A, 40°C Ambient on 6.4 x 6.4 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 42 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 30 40 50 Figure 63. Duty Cycle for the ST23-6 with the SMD-761x, 24 VDC ST23-6 Max Duty Cycle vs Speed 24 VDC, 5.0 Amps, 40°C Ambient on 6.4 x 6.4 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 30 40 50 Figure 64. Duty Cycle for the ST23-6 with the SMD-761x, 48 VDC ST23-6 Max Duty cycle vs Speed 48 VDC, 5.0 Amps 40°C Ambient on 6.4 x 6.4 x .25 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 43 Figure 65. Duty Cycle for the ST34-2 with the SMD-761x, 48 VDC ST34-2 Max Duty cycle vs Speed 48 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) Figure 66. Duty Cycle for the ST34-2 with the SMD-761x, 80 VDC ST34-2 Max Duty cycle vs Speed 80 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 44 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 30 40 50 Figure 67. Duty Cycle for the ST34-5 with the SMD-761x, 48 VDC ST34-5 Max Duty Cycle vs Speed 48 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 30 40 50 Figure 68. Duty Cycle for the ST34-5 with the SMD-761x, 80 VDC ST34-5 Max Duty cycle vs Speed 80 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 30 40 50 Speed (RPS) NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 45 Figure 69. Duty Cycle for the ST34-8 with the SMD-761x, 48 VDC ST34-8 Max Duty Cycle vs Speed 48 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 30 40 50 Figure 70. Duty Cycle for the ST34-8 with the SMD-761x, 80 VDC ST34-8 Max Duty cycle vs Speed 80 VDC, 10.0 Amps 40°C Ambient on 10 x 10 x .5 Aluminum Plate 100 % Duty Cycle 80 60 40 20 0 0 10 20 Speed (RPS) 46 | ni.com | NI SMD-7613/7614/7615/7616 User Manual 30 40 50 Drive Heating While NI SMD-7613/7614/7615/7616 devices efficiently transmit power between the power supply and motor, they do generate some heat in the process. This will cause the temperature of the drive to rise above the surrounding air temperature and may also require that the drive be mounted to a heat conducting metal surface. To calculate the power dissipation and temperature rise, the following information is provided. Given: drive power dissipation Pd versus motor (refer to the figures below) drive thermal constant RQ The final drive case temperature is given by: TC = Ta + RQ* Pd where Ta is the ambient temperature of the surrounding air. The case of the drive should not be allowed to exceed 70 °C or the life of the product could be reduced. Drive thermal constant: Narrow side of drive mounted on a 3.5” × 13.5” steel plate, 0.070 in. thick: Rθ = 1.0 °C/W Narrow side of drive mounted on a non-heat conducting surface: Rθ = 2.1 °C/W Figure 71. Drive Thermal Losses SMD-7611/7612 Drive Losses 25 60V 48V 24V Driver Loss (W) 20 15 10 5 0 1 2 3 4 5 Motor Current (A) NI SMD-7613/7614/7615/7616 User Manual 6 | 7 8 © National Instruments | 47 Mechanical Outline Figure 72. Mechanical Dimensions 1.775 0.663 5.0 0.61 3.00 1.98 6X SLOT 0.16 WIDE, FULL R 4.74 Technical Specifications Amplifier Features .....................................................Digital MOSFET. 20 kHz PWM. Suitable for driving step motors with four, six, or eight leads. SMD-7613/7615 Supply voltage ..................................12 to 53 VDC Motor current ....................................0.5 to 5.0 A/phase peak of sine SMD-7614/7616 Supply voltage ..................................18 to 88 VDC Motor current ....................................0.5 to 10.0 A/phase peak of sine 48 | ni.com | NI SMD-7613/7614/7615/7616 User Manual Digital inputs Step & Direction Isolation ............................................ Optically isolated, 5 V logic Digital logic ...................................... 5 V, differential Internal resistance ............................. 330 Ω Minimum pulse width....................... 0.5 µsec Minimum set-up, direction ............... 2 0.5 µsec Other inputs Isolation ............................................ Optically isolated, 12 V logic Digital logic ...................................... 12 to 24 V, differential Internal resistance ............................. 22000 Ω Analog inputs Input voltage ............................................. ±10 VDC Internal resistance ..................................... 100 kΩ Output ............................................................... Photodarlington, 100 mA, 30 VDC max. Voltage drop.............................................. 1.2 V max at 100 mA +5V Output ....................................................... 5 VDC Max current............................................... 100 mA Dimensions ....................................................... 1.775 × 3.0 × 5.0 in. (45 × 76.2 × 127 mm) Weight............................................................... 10 oz (280 g) Operating temperature range ............................ 0 °C to 40 °C Mating connectors Motor/power supply ................................. Phoenix Contact 1757051 (included) IN/OUT1................................................... DB-25 male (included) Encoder feedback ..................................... HD-15 male Accessories Regeneration clamp .................................. NI SMD-7700, NI part number 748908-01 NI SMD-7613/7614/7615/7616 User Manual | © National Instruments | 49 Alarm Codes In the event of an error, the green LED on the main board will flash one or two times, followed by a series of red flashes. The pattern repeats until the alarm is cleared. Table 5. Status LED Blink Code Definitions Blink sequence Code Error G Solid green No alarm, motor disabled GG (slow) Flashing green No alarm, motor enabled RG 1 red, 1 green Motor stall (encoder-equipped only) RGG 1 red, 2 green Move attempted, drive disabled RRG 2 red, 1 green CCW limit RRGG 2 red, 2 green CW limit RRRG 3 red, 1 green Drive overheating RRRGG 3 red, 2 green Internal voltage out of range RRRRG 4 red, 1 green Power supply overvoltage RRRRGG 4 red, 2 green Power supply underoltage RRRRRG 5 red, 1 green Over current /short circuit RRRRRGG 5 red, 2 green Motor resistance out of range RRRRRRG 6 red, 1 green Open motor winding RRRRRRGG 6 red, 2 green Bad encoder signal RRRRRRRG 7 red, 1 green Serial communication error RRRRRRRRG 8 red, 1 green Internal voltage out of range Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015. © 2014 National Instruments. All rights reserved. 374809A-01 Sep14