Bulletin 800A 16 mm Push Buttons 10 IP65, Type 13 Bulletin 800A • • • • 0 IEC Style 16 mm Mounting Hole IP65 NEMA Type 13 Internationally Rated Operators TABLE OF CONTENTS Description Page Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-297 Push Buttons Momentary Contact, Non-Illuminated . . . . . . . . . . . . . . . . . . 10-298 Momentary Contact, Illuminated. . . . . . . . . . . . . . . . . . . . . . 10-298 Maintained, Illuminated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-298 Pilot Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-298 Selector Switches 2-Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-300 3-Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-300 10-296 Description Page Rotary Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-300 Modifications and Accessories Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-302 Color Lens Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-303 Lens Caps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-303 Diffuser Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-303 Replacement Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-303 Legend Inserts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-304 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-305 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Specifications ➊ Electrical Ratings 1 A, 125V AC 1 A, 250V AC resistive Maximum Contact Ratings 1 A, 28V DC resistive 1 mA, 5V DC low level 100 mA, 50 mV dry circuit Continuous 5 A (lth) Mechanical Ratings File E14840 Guide NKCR UL Listed LR1234 (operators) LR2923 (assembled panels) CSA Approved IEC Compliance IEC 144 Mechanical endurance 1,000,000 cycles Contact material Gold plate over silver Contact bounce 3 ms (typical) Electrical life 200,000 cycles at rated load Dielectric strength 1000V RMS at sea level Environment Temperature range Note: Operating temperature ranges below +32°°F (0°C) are based on the absence of freezing moisture and liquids. –4…+113°°F (–20…+45°°C) –22…+185°°F (–30…+85°°C) 1, 3, 12, and 13; IEC 144, IP65 Operating Storage NEMA Types Construction 1 N.O. - 1 N.C. (Form Z), SPST Double-break contacts Circuits Gold-plated, solderable, quick connect stabs 0.110" x 0.020" or PC board/wire wrap pin 0.020" x 0.030" (0.210" long) terminals Contact terminals Lamp terminals Tin-plated ➊ Performance Data — see page Important-2. Termination Units are available with quick-connect stab or PC board terminals. PC Board Pin Termination Terminal Spacing — PC Pin Termination 0 0.200" (5.08) Stab Terminations 0.200" (5.08) 0 0.150" (3.81) 0 0.110" x 0.020" solderable stabs are compatible with AMP connector Part No. 61060-1 or equivalent. These connectors will accept one #18 or two #22 AWG wires maximum. Contact terminals are gold-plated and lamp terminals are tin-plated. 0.020" x 0.030" (0.210" long) require a 0.036" diameter hole for direct PC board mount or quick-connect PC board pin sockets (Cat. No. 800A-N66). Stab and PC Board Pin Circuit Layout 0.136" (3.45) 0.150" (3.81) 0.136" (3.45) ➋ ➋ Lamp terminals are not provided on knob or key selector switches. 10-297 1 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Push Buttons and Pilot Lights — Round, Square, and Rectangular Bezel Round Bezel Cat. No. 800A-T2AR24 Square Bezel Cat. No. 800A-M2FR Rectangular Bezel Cat. No. 800A-L2CR24 Momentary Non-Illuminated Push Buttons Contact Type Operator Type Round Square Cat. No. Cat. No. Cat. No. Stab Red Green 800A-M2AR 800A-M2AG 800A-M2BR 800A-M2BG 800A-M2CR 800A-M2CG PC pin Red Green 800A-C2AR 800A-C2AG 800A-C2BR 800A-C2BG 800A-C2CR 800A-C2CG Stab Red Green 800A-M2ER 800A-M2EG 800A-M2FR 800A-M2FG 800A-M2GR 800A-M2GG PC pin Red Green 800A-C2ER 800A-C2EG 800A-C2FR 800A-C2FG 800A-C2GR 800A-C2GG Rectangular Termination Color Extended 1 N.O. 1 N.C. Flush Rectangular Momentary Illuminated Push Buttons Lamp Type and Volts Contact Type Operator Type Round Square Cat. No. Cat. No. Cat. No. Stab Red Green 800A-M2AR24 800A-M2AG24 800A-M2BR24 800A-M2BG24 800A-M2CR24 800A-M2CG24 PC pin Red Green 800A-C2AR24 800A-C2AG24 800A-C2BR24 800A-C2BG24 800A-C2CR24 800A-C2CG24 Stab Red Green 800A-M2ER24 800A-M2EG24 800A-M2FR24 800A-M2FG24 800A-M2GR24 800A-M2GG24 PC pin Red Green 800A-C2ER24 800A-C2EG24 800A-C2FR24 800A-C2FG24 800A-C2GR24 800A-C2GG24 Rectangular Termination Color Extended 0 Incandescent 24V AC/DC 1 N.O. 1 N.C. Flush Maintained Illuminated Push Buttons Lamp Type and Volts Contact Type Operator Type Round Square Cat. No. Cat. No. Cat. No. Stab Red Green 800A-T2AR24 800A-T2AG24 800A-T2BR24 800A-T2BG24 800A-T2CR24 800A-T2CG24 PC pin Red Green 800A-F2AR24 800A-F2AG24 800A-F2BR24 800A-F2BG24 800A-F2CR24 800A-F2CG24 Stab Red Green 800A-T2ER24 800A-T2EG24 800A-T2FR24 800A-T2FG24 800A-T2GR24 800A-T2GG24 PC pin Red Green 800A-F2ER24 800A-F2EG24 800A-F2FR24 800A-F2FG24 800A-F2GR24 800A-F2GG24 Rectangular Termination Color Extended Incandescent 24V AC/DC 1 N.O. 1 N.C. Flush Pilot Lights Lamp Type and Volts Contact Type Operator Type Round Square Cat. No. Cat. No. Cat. No. Stab Red Green 800A-L2AR24 800A-L2AG24 800A-L2BR24 800A-L2BG24 800A-L2CR24 800A-L2CG24 PC pin Red Green 800A-E2AR24 800A-E2AG24 800A-E2BR24 800A-E2BG24 800A-E2CR24 800A-E2CG24 Stab Red Green 800A-L2ER24 800A-L2EG24 800A-L2FR24 800A-L2FG24 800A-L2GR24 800A-L2GG24 PC pin Red Green 800A-E2ER24 800A-E2EG24 800A-E2FR24 800A-E2FG24 800A-E2GR24 800A-E2GG24 Termination Color Extended Incandescent 24V AC/DC 1 N.O. 1 N.C. Accessories — Page 10-302 Lamp Information — Page 10-303 10-298 Flush Legend Plates — Page 10-304 Dimensions — Page 10-305 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Push Buttons and Pilot Lights — Round, Square, and Rectangular Bezel 800A – M 2A A 24 C b c d e a a b (cont’d) d d (cont’d) Operator Type Bezel Type Lamp Type and Voltage Lamp Type and Voltage Stab Type Termination ➊ Flush Head Description Code Description M Momentary push button 2E Round T Maintained push button 2F Square Pilot light 2G Rectangular L PC Pin Type Termination ➋ Code Description C Momentary push button F Maintained push button E Pilot light b Bezel Type Description Code Blank Non-illuminated (supplied without lamp) 6L 6V AC/DC 2L 12V AC/DC 4L 24V AC/DC Incandescent Description c Description 06 6V AC/DC Lens Cap 12 12V AC/DC Code Description 24 24V AC/DC 10 120V AC 20 240V AC Code Description Blank Leave blank if no lens cap or lamp desired X Used only when lamp and no lens cap is desired 0L 120V AC Neon ➏ e Factory Assembly Amber B Blue Description C Clear 2A Round G Green 2B Square R Red ➌ 2C Rectangular Code Code Code A Extended Head LED ➍➎ Non-Illuminated Code Code Description Blank Leave blank for no factory assembly C Completely assembled Push Buttons and Pilot Lights, Large Square Bezel 800A – M 2D A 24 C b c d e a a b d d (cont’d) Operator Type Bezel Type Lamp Type and Voltage Lamp Type and Voltage Stab Type Termination ➊ Code Description Code Description 2D Extended head large square M Momentary push button 2H Flush head large square T Maintained push button L 1 Code Description C Momentary push button F Maintained push button E Indicating light Description Code Blank Non-illuminated (supplied without lamp) 6L 6V AC/DC 2L 12V AC/DC 4L 24V AC/DC c Indicating light PC Pin Type Termination ➋ Incandescent Lens Cap Code Description Code Description 06 6V AC/DC Blank Leave blank if no lens cap or lamp desired 12 12V AC/DC 24 24V AC/DC X A Used only when lamp and no lens cap is desired LED ➍➎ Non-Illuminated Code 0L Blue C Clear G Green R Red ➌ ➊ 0.110" x 0.20" solderable stab terminals are compatible with AMP connector part no. 61060-1 or equivalent. ➋ Compatible with PC pin connector Cat. No. 800A-N66. Available in packs of 50. ➌ Red flush head push buttons are not suitable for applications requiring extended head, or other unguarded buttons capable of being operated quickly in emergencies, and they may not comply with applicable codes or standards. 120V AC Neon ➏ Code Description 10 120V AC 20 240V AC e Amber B Description Factory Assembly Code Description Blank Leave blank for no factory assembly C Completely Assembled ➍ LEDs are only available in red, green, amber, and white; lens color must match LED color. For white LED, use clear lens cap. LEDs include internal current limiting resistors. ➎ White LED available in 24V AC/DC only. ➏ Neon lamps are only available with clear, amber, or red lens cap. 10-299 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Selector Switches and Rotary Operators Round Bezel, Knob Operator Cat. No. 800A-H2AW Square Bezel, Cylinder Lock Cat. No. 800A-HC2B Rectangular Bezel, Knob Operator Cat. No. 800A-G2CW 2-Position Cylinder Lock and Knob Operated Selector Switches Operator Position Round Termination Type Operator Type Stab PC pin Stab PC pin Square Rectangular Cat. No. Cat. No. Cat. No. 800A-HC2A 800A-GC2A 800A-H2AW 800A-G2AW 800A-HC2B 800A-GC2B 800A-H2BW 800A-G2BW 800A-HC2C 800A-GC2C 800A-H2CW 800A-G2CW Round Square Rectangular Cat. No. Cat. No. Cat. No. Operator Function Key O X X O Knob O X X O Maintained in both positions Note: X = Closed/O = Open 3-Position Selector Switches Operator Position Termination Type Poles Per Position X O O X O O X O O One Solder lug Two 0 O X O O X O O X O O O X O O X O O X Operator Function M = Maintained S = Spring Return M M 800A-JJ2AW 800A-JJ2BW 800A-JJ2CW S→M←S M 800A-JB2AW 800A-JB2BW 800A-JB2CW M M M 800A-JH2AW 800A-JH2BW 800A-JH2CW M M←S 800A-JR2AW 800A-JR2BW 800A-JR2CW 800A-JL2AW 800A-JL2BW 800A-JL2CW S→M M Note: X = Closed/O = Open Rotary Operators The rotary operator kit provides a means to actuate rotary switches and potentiometers and maintains consistent panel appearance. The kit contains all necessary hardware to accommodate potentiometers, or multi-run switches (Type W potentiometers are available through electronic component distributors or Grayhill Series 50 rotary switch elements). Dimensional requirements of elements must comply with the switch in figures 1 and 2 shown on this page. Potentiometer or switch not included. Note: For operator dimensional information, refer to page 10-305. Rotary Operator Kits (Operator Only) Square Rectangular Cat. No. Cat. No. 800A-P2BW 800A-P2CW Round Cat. No. 800A-P2AW Large Square Cat. No. 800A-P2DW Approximate Dimensions 1/ 4 (6.35) Dia. 13/ 64 (5.08) 1/ 4 (6.35) 1/ 4 (6.35) 1/ 2 1/ 8 (12.7) Dia. 3/ 8 (9.53) 1/ 4 (6.35) Figure 1 Rotary Switch Accessories — Page 10-302 Legend Plates — Page 10-304 10-300 (3.18) 3/ 16 (4.83) 1/ 2 (12.7) Dia. 1/ 4 3/ 32 (2.39) 1/ 4 (6.35) (6.35) 3/ 32 1/ 8 (3.18) Dia. (2.39) Figure 2 Potentiometer Dimensions — Page 10-305 Bulletin 800A 16 mm Push Buttons IP65, Type 13 2-Position Selector Switches and Rotary Operators 800A– H a 800A– GC 2A W b c (Selector Switch and Potentiometer Operator) 2A (Cylinder Lock) b a1 c1 Selector Switch Information 90o 1 1 2 (Terminal 1…2) X O (Terminal 3…4) O X 2 Contact Function: X = Closed/O = Open Knob Operator a Standard Knob Selector Switch with Stab Terminals Code H K Description Maintained Spring return from right Standard Knob Selector Switch with Pin Terminals Code G R Code Description Maintained: lock in left or right position ➊ HC Cylinder Lock with Pin Terminals Code Description Maintained: lock in left or right position ➊ GC Description Maintained Spring return from right P Description Potentiometer, rotary switch operator (with knob only) Code A B G R W Y Bezel Type Code Blank 01 02 03 04 05 06 07 Description Round Square Rectangular Large square Description Orange Blue Green Red White Yellow c1 Optional Key Code b Code 2A 2B 2C 2D c1 (cont’d) Optional Key Code Knob Insert Color ➋ Cylinder Lock with Stab Terminals Potentiometer Operators Code c a1 Operator Type Operator Type KEY Operator Description Standard key Custom key #1 Custom key #2 Custom key #3 Custom key #4 Custom key #5 Custom key #6 Custom key #7 Code 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Description Custom key #8 Custom key #9 Custom key #10 Custom key #11 Custom key #12 Custom key #13 Custom key #14 Custom key #15 Custom key #16 Custom key #17 Custom key #18 Custom key #19 Custom key #20 Custom key #21 Custom key #22 Custom key #23 Custom key #24 3-Position Selector Switches 800A– JH 2A W b c a Terminal Configuration for 800A-JB, JJ Terminal Configuration for 800A-JH, JR, JL Terminal Dimensions Selector Operation 2 2 3 4 2 C1 3 4 7 8 C1 1 9 3 C2 a a (cont’d) b c Operator Type Operator Type Bezel Type Knob Insert Color ➋ Standard Knob Selector Switch with Solder Lug Terminals ➌ (one pole per position) Standard Knob Selector Switch with Solder Lug Terminals ➌ (two poles per position) Code JB JJ Description Spring return — both Maintained Code JH JR JL Description Maintained Spring return right Spring return left Code 2A 2B 2C 2D Description Round Square Rectangular Large square Code A B G R W Y Color Orange Blue Green Red White Yellow Note: Low security locks. Key interchangeability possible. ‘ ➊ Key removable in locked position only. ➋ Special colors — Selector switches and rotary kits are factory assembled with a white color insert as standard. Other colors are available factory assembled at no additional charge if ordered in quantities of five or more. ➌ Solder lug termination dimensions shown above are smaller than standard 800A stab terminations. 10-301 1 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Modifications and Accessories Closing Plugs Flip Covers PC (Printed Circuit) Board Pin Sockets Hole Closing Plugs Cat. No. 800A-N1 Flip Covers Cat. No. 800A-N42, -N12 PC Board Sockets Cat. No. 800A-N66 Bulletin 800A closing plugs are designed to allow closure of an unoccupied operator opening on a panel or enclosure. This plug fits standard 16 mm openings and offers NEMA Type 13 rating when installed with the standard gasket and diecast mounting ring. Bulletin 800A operator flip covers offer nominal protection from unwanted operation while allowing operator visibility through a clear cover. The rectangular cover fits Bulletin 800A operators with square or rectangular bezels. Large square covers fit only large square push buttons. These sockets are intended for use with PC pin style Bulletin 800A operators. Sockets can be secured directly to printed circuit boards providing mass termination benefits. Sockets can be secured to circuit boards by either soldering or with screw fasteners. Refer to the diagram on page 10-305. Cat. No. 800A-N1 Rotary Operator Assembly Tool Description Cat. No. Cat. No. Rectangular flip cover 800A-N42 800A-N66 Large square flip cover 800A-N12 Lamp Installation/Removal Tool Note: Sold only in multiples of 50. Custom Legend Kit 0 Rotary Operator Assembly Tool Cat. No. 800A-N60 An assembly tool is recommended for rotary operators. Cat. No. 800A-N60 Insulation Sleeve Lamp Installation/Removal Tool Cat. No. 800M-N5 Cat. No. 800M-N5 Mounting Ring Wrench Custom Legend Kit Cat. No. 800MS-N13 A legend marking kit is available to help create custom legend inserts. Each kit contains six grid sheets (four for use on the large square devices and two for use on the square, round, and rectangular devices). The grid sheets outline the working area available for adding a legend and also provides the necessary instructions and recommendations required to create custom legend inserts. Cat. No. Insulation Sleeve Cat. No. 800A-N51 The insulation sleeve slips over the Bulletin 800A wiring terminals to provide electrical insulation from adjacent equipment. Cat. No. 800A-N51 Note: Sold only in multiples of 20. 10-302 Mounting Ring Wrench Cat. No. 800A-N50 This wrench simplifies the installation of the Bulletin 800A units and is recommended when close packing is required. Cat. No. 800A-N50 800MS-N13 Special Bezel Colors All standard devices are shipped with black bezels. To order devices with gray, red, yellow, or metallic bezels, consult your local Allen-Bradley Sales Office. Bulletin 800A 16 mm Push Buttons IP65, Type 13 Modifications and Accessories, Continued Large Square Color Lens Caps Large square replacement lens caps include a white optic plate. Large Square Color Lens Cap Cat. No. 800A-N10A Description Cat. No. Amber w/optic plate 800A-N10A Blue w/optic plate 800A-N10B Clear w/optic plate 800A-N10C Green w/optic plate 800A-N10G Red w/optic plate 800A-N10R Lens Caps Replacement lens caps are available. Lens caps are packaged in multiples of five. Lens caps must be ordered in multiples of five only. Color Amber Round Square Cat. No. Cat. No. Rectangular Cat. No. 800A-N20A 800A-N30A 800A-N40A Blue 800A-N20B 800A-N30B 800A-N40B Clear 800A-N20C 800A-N30C 800A-N40C Green 800A-N20G 800A-N30G 800A-N40G Red 800A-N20R 800A-N30R 800A-N40R White Diffuser Inserts Diffuser inserts, for improved legend legibility on illuminated surfaces, are available as a prescored sheet. The cat. no. as listed in the table below represents one sheet of six pieces. Diffuser inserts must be ordered in multiples of five. Description Cat. No. Round diffuser insert 800A-N25 Square diffuser insert 800A-N35 Rectangular diffuser insert 800A-N45 Large square diffuser insert 800A-N11 Replacement Lamps Use the table below to order replacement lamps. The cat. no. as listed represents one lamp. Lamps can only be ordered in multiples of ten. White LEDs operating on 24V AC/DC are available. Consult your local Allen-Bradley Sales Office. Lamp Incandescent ➊ Neon ➋ LED ➌ Type Operator Voltage ANSI Number Cat. No. Full voltage and transformer 6.3 86 800M-N15 14 73 800M-N16 24 85 800M-N17 120 — 800A-N110 Full voltage — Full voltage 240 — 800A-N120 6 AC/DC — 800T-N60x ➍ 12 AC/DC — 800T-N61x ➍ 24 AC/DC — 800T-N62x ➍ 120 AC — 800T-N64x ➍ ➊ Wedge base (ANSI #85) incandescent lamps are subject to significantly shortened lamp life during 24V DC operation. Use wedge base LEDs for longer lamp life. ➋ Resistors are supplied with unit and must be connected in series with lamp. 120V neons use a 47K, 1/4 watt resistor, 240V neons require two 47K, 1/4 watt resistors; typical forward current 1.2 mA. ➌ LEDs have built in current limiting resistors. ➍ To complete the cat. no. replace the x with the first letter of the desired color: Amber, Green or Red. 10-303 1 Bulletin 800A 16 mm Push Buttons IP65, Type 13 Legend Inserts Legend Inserts for Large Square Units Standard legend inserts are only available for the large square units as listed below. To order, select the desired cat. no. from the table below. Note: Standard legend inserts are not available for round, square or rectangular units, a custom legend kit (Cat. No. 800MS-N13) is recommended. See page 10-302. Marking Cat. No. Marking Cat. No. CLOSE 800MS-WC01 RAISE 800MS-WC14 DOWN 800MS-WC02 RESET 800MS-WC15 FAST 800MS-WC03 REV 800MS-WC16 FORWARD 800MS-WC23 RUN 800MS-WC17 HIGH 800MS-WC04 SLOW 800MS-WC18 IN 800MS-WC06 START 800MS-WC19 INCH 800MS-WC07 STOP 800MS-WC20 JOG 800MS-WC08 EMERG STOP 800MS-WC24 LOW 800MS-WC05 TEST 800MS-WC21 LOWER 800MS-WC11 UP 800MS-WC22 OFF 800MS-WC09 1ST SPEED 800MS-WC25 ON 800MS-WC10 2ND SPEED 800MS-WC26 OPEN 800MS-WC13 3RD SPEED 800MS-WC27 OUT 800MS-WC12 4TH SPEED 800MS-WC28 PUSH-TO-TEST 800MS-WC29 — — Legend Character Guidelines (Working Area) The following approximate dimensions provide a guideline for determining the maximum usable legend area. The maximum thickness for legend films should not exceed 0.005" (0.127 mm). Dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. 0 45/ Sq. 64 17/ Dia. 32 (13.2) (17.8) 11/ 16 7/ Sq. 16 (17.4) (11.1) 7/ 16 (11.1) Round Square Rectangular Large Square Legend Markings Large square selector switches and rotary operators may be engraved per the diagram below. Specify cat. no. and custom engraving. Character dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. 6 characters maximum at 1/8 (3.2) high 4 characters maximum at 1/8 (3.2) high 8 characters maximum at 1/8 (3.2) high 9 characters maximum at 1/8 (3.2) high 10-304 6 characters maximum at 1/8 (3.2) high Bulletin 800A 16 mm Push Buttons IP65, Type 13 Approximate Dimensions and Shipping Weights Dimensions in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. Mounting Dimensions 13/ 64 13/ 64 (5.1) (5.1) Mounting Requirements for Screw Fasteners- #1-64 Pan Head Screw from Top. Or #2-32 Type B Thread Forming Screw from Bottom. 5/ 32 5/ (16) 8 (3.9) A +0.005 –0.000 diameter Mounting with Anti-Turn Feature 3 1 a b 5/ 64 (1.9) B 11/ 32 (8.7) 2 4 5/ 32 (3.9) 9/ 16 (14.2) 9/ 64 7/ 64 (2.80) 1/ 32 (.79) Dia. 9/ 64 (3.5) 1/ 4 (6.4) (3.5) 5/ 8 (15.9) Dia. Knob Operator 1➊ (25.4) Push Button Key Operator ±.005 37/ 64 (14.7) ±.005 45/ 64 (17.8) ±.010 39/ (15.5) 64 C D C➋ D Shipping Wt. for Rectangular Push Button 0.71 oz. (20 gm) D Shipping Wt. for Rectangular Selector Switch 0.78 oz. (22 gm) Shipping Wt. for Rectangular Selector Switch 1.34 oz. (38 gm) ➊ Rotary switch depth without switch element or potentiometer. ➋ Rotary switch operator only will vary in length behind panel according to element selection. 1 Panel Thickness Requirements — Devices will accommodate panel thicknesses from 1/16" (1.6 mm) to 3/16" (4.8 mm). Mounting Torque Range — 10…12 lb-in. (1.1…1.3 Nm) Dimension D Operator Dimension A Dimension B Dimension C Round 23/64 (9.1) 23/64 (9.1) 1-3/4 (44.5) 13/32 (10.3) Push Button Square 23/64 (9.1) 23/64 (9.1) 1-3/4 (44.5) 13/32 (10.3) Rectangular 61/64 (24.2) 23/64 (9.1) 1-3/4 (44.5) 13/32 (10.3) Large rectangular 1-13/64 (30.6) 1-13/64 (30.6) 1-3/4 (44.5) 35/64 (13.9) Knob Key 3/4 (19.1) 1-11/32 (34.1) Wiring Diagrams (See Applicable Codes and Laws) Rectangular Push Buttons Square .704 Sq. (17.9) Round .704 (17.9) 1 2 4 3 a (+) b (–) Large Square .944 (23.98) Selector Switches .704 (17.9) 1.2 Sq. (30.5) 1 2 4 3 10-305