H G F 46,1 max. E 20,9 max. D C B A 1,5 PCB hole pattern F F edge of daugther card for reference only (2x ) 13,4 `0,05 6 `0,05 n2,65 + 0,1 -0 (2x) 12,47 `0,05 A 4,5 `0,05 2 `0,05 14x suggested hole size 24,08 24,5 `0,05 3,9 `0,05 6,6 `0,05 +0 - 0 ,1 4,5 `0,05 Marking on opposite side (see note 6) E 12,47 `0,05 ,7 14,72 41,3 max. 18,65 n1 E 33 b 28,6 max. 4,95 3,9 `0,05 17,5 max. 6,6 `0,05 13 b B 3 `0,05 18,5 `0,05 10 `0,05 21,2 `0,05 Contact 27 datum plane 12 `0,05 22,55 `0,05 9 10 5 8x suggested hole size 14,5 `0,05 4 23,9 `0,05 D Drilled hole n1,15 `0,025 8 Contact 27 datum plane (14x) 2 3 Tin thickness minimum 15µm Tin thickness minimum 15µm Finished hole + 0,09 n1 - 0,06 (14x) 1,5 1 7 11 (8x) Copper thickness minimum 25µm Copper thickness minimum 25µm 6 C D Drilled hole n1,75 `0,025 Finished hole + 0,09 n1,6 - 0,06 A ( 10 : 1 ) C (8x) B ( 10 : 1 ) NOTES: 1. MATERIALS AND FINISHES: - INSULATOR: GLASS FILLED PLASTIC UL 94 V-0 RATED, GREY RAL 7035 1 1 3 1 3 1 3 3 2 3 3 quantity - CONTACTS: COPPER ALLOY, PLATING MATING AREA: FLASH GOLD OVER NICKEL PLATING TERMINATION AREA: 0,8-1,5 µM TIN (SN 100) 2. ELECTRICAL CHARACTERISTICS: CREEPING AND CLEARANCE DISTANCE; MINIMUM SPACING: B - CONTACTS 5-16 TO ANY OTHER CONTACT WITHIN THIS GROUP: 0,7 MM - CONTACT 25 TO 26: 5,5 MM - CONTACTS 27-34 TO ANY OTHER CONTACT WITHIN THIS GROUP: 1,4 MM - CONTACTS 25-26 TO 27-29: 2,0 MM CONTACT CURRENT RATING: - POWER CONTACTS: 16 AMPERES MINIMUM, TESTED PER CSA C22.2 NO. 182.3-M1987, ALL CONTACTS UNDER LOAD Fixing plate Case 34pos. male Power contact type 4 Power contact type 3 Power contact type 2 Power contact type 1 Signal contact type 7 Signal contact type 6 Signal contact type 4 Signal contact type 2 Signal contact type 1 part description 11 10 9 8 7 6 5 4 3 2 1 item B dwg no./ norm - SIGNAL CONTACTS: 2 AMPERES NOMINAL - POWER CONTACTS: 0,0022 OHM MAX. - SIGNAL CONTACTS: 0,0085 OHM MAX. INSULATION RESISTANCE: 5 G OHM PER IEC 512-2, TEST 3a, METHOD A 3. POSITIONS WITHOUT CONTACTS: 1-4, 17-24 4. WORKING TEMPERATURE: -55°C TO +125°C 5. PRESS-FIT PART OF CONTACTS ARE PATENT PROTECTED 6. CONNECTOR IS PART MARKED: PART-NO. CONEC ABC H G F E D C DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH INITIAL CONTACT RESISTANCE PER IEC 512-2, TEST 2b: A material partlist finish: tolerance see notes ISO 2768-m 07.06.05 PRESS-FIT ANGLED AdvancedTCA Kühle dwg no: d-old Ä 2592 rev. description 24.10.06 HS date name Inventor 46K1A007 R part no: B see notes PLUG CONNECTOR 22pos. Schmidt norm 2xb 2,5:1 (10:1) title: name date drawn 07.06.05 appd. dim. in mm scale: material: A DINA2 sh: 1 ATC22W08MAE3S5X A