F E D C B A NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 240°C FOR 5 SEC. AND SOLDER PREHEAT 120°C FOR 120 SEC.) 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL (5:1) 4. SIGNAL CONTACTS: COPPER ALLOY PLATING: GOLD FLASH over NICKEL D 5. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING, MATING AREA: GOLD FLASH over NICKEL 7,25 `0,3 8,7 `0,3 3. INSULATORS: PBT GF UL 94 V-0; GREEN SEALING COMPOUND D PLATING, TERMINATION SIDE: 160-240µin TIN over 80µin NICKEL 6. THREADED LOCKS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. COLLARS: COPPER ALLOY, min. 200µin TIN over 80µin NICKEL 8. FRAME: ZINC DIE CAST; NICKEL PLATED 12. P.C.B. HOLE DRILLINGS + RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3,1 in.LB) / max. 40Ncm (3,5 in.LB) 5,73 +- 0,17 0,08 11. HEXLOCKING SCREWS: STAINLESS STEEL 3,6 +- 0,25 0 9. O-RING: SILICON; BLUE 10. SEALING COMPOUND: PUR; BLUE 14. CONNECTOR IS PART MARKED: 6009W4SAR68B50X CONEC ABC 0,02 8 +- 0,23 61,4 +- 0,3 0 47,04 `0,13 C C 21,1 +- 0,3 0 38,5 +- 0,25 0 10° SW 4,8 4-40 UNC n0,64 `0,05 (5x) B 9,4 4,6 B n1,95 (4x) 6,1 4-40 UNC O-RING 6009W4SAR68B50X CONEC ABC SEE NOTE 8 Ø4 SEE NOTE 14 4-40 UNC Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 05.02.13 Henneboel D-SUB COMBINATION FEMALE appd. 05.02.13 Fischer 9W4S with threaded lock and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 15K1A1266 R a B sh: 1/2 6009W4SAR68B50X A F E D C B A D D 47,04 `0,13 14,48 `0,1 14,48 `0,1 8,28 `0,1 7,77 `0,1 n3,1 `0,1 (2x) 5,54 `0,1 A1 1,42 `0,1 2,84 `0,1 1 n1 +- 0,1 0 (5x) n2,3 `0,1 (4x) 4,14 `0,1 6,91 `0,1 C C 9,68 `0,1 P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) 42,5 `0,1 i 0,26 A 11,4 `0,1 B n3,1 `0,05 (2x) B R3 ,4 ` 10°`1° 47,04 `0,1 B i 0,26 B 0, 13 A A F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH RECOMMENDED PANEL CUT-OUT scale: material: tolerance 3:1 SEE SHEET 1 dim. in mm date A title: name drawn 05.02.13 Henneboel P.C.B. HOLE DRILLINGS appd. 05.02.13 Fischer RECOMMENDED PANEL CUT-OUT D-SUB COMBINATION FEMALE 9W4S dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 15K1A1266 R a B sh: 2/2 SEE SHEET 1 A