F E D C B A n0,65 `0,05 (15x) NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 (5:1) 2. METALSHELLS: COPPER ALLOY; min. 320µin TIN over 40-80µin NICKEL 3. INSULATORS: HIGH TEMPERATURE PLASTIC UL 94 V-0, BLACK 4. SIGNAL CONTACTS: COPPER ALLOY; PLATING (SEE PART NO): o PLEASE ADD B for 20µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD C for 30µin HARD GOLD over min. 50µin NICKEL SOLDER CUP ACCEPTS CABLE AWG 26 SEALING COMPOUND 7,26 +- 0,34 0,26 3,6 +- 0,25 0 o PLEASE ADD A for GOLD FLASH over NICKEL (PREFERRED TYPE) D D 5. THREADED INSERTS: COPPER ALLOY; min 200µin TIN over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min 200µin TIN over 80µin NICKEL 7. FRAME: ZINC DIE CAST; NICKEL PLATED 8. RUBBER-GASKET: TPE; BLACK 9. HEXLOCKING SCREWS: STAINLESS STEEL 5,7 +- 0,12 0,18 10. O-RING: SILICON; BLUE 11. SEALING COMPOUND: PUR; BLUE 12. CAPACITANCE: 180pF`20% 13. DIELECTRIC WITHSTANDING VOLTAGE: 424 VDC 14. RECOMMENDED PANEL CUT-OUT ON SHEET 2 15. RECOMMENDED TORQUE FOR MOUNTING SCREW 35N cm (3.1 in.LB) / 8,26 +- 0,22 0,03 max. 40N cm (3,5 in. LB) 16. CONNECTOR IS PART MARKED: 6STF15PoM01B20X CONEC ABC (see note 4) RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR C C FILTER IS TOTALLY GUARDED AGAINST HUMIDITY. 47,7 +- 0,3 0 POS. 1 WATER COULD PENETRATE INTO THE MATING AREA. 33,3 +- 0,15 0,1 POS. 9 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER 25,17 +- 0,2 0,05 21,1 +- 0,3 0 RESISTANT CAP OR HOOD. 10° B B O-RING 6STF15PoM01B20X CONEC ABC M3 SEE NOTE 7 4,6 9,4 SEE NOTE 16 SW 4,75 Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH M3 scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 16.07.13 Schmidt D-SUB FILTER MALE appd. 16.07.13 Fischer 15pos. SOLDER CUP with threaded insert and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 sh: 1 15K1A1343 R a B 6STF15PoM01B20X (see note 4) A F E D C B A Solder Instruction D D 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 28,8 `0,1 i 0,26 A ,4 R3 ` 1 0, 3 11,4 `0,1 B Ø3,1 `0,05 (2x) B 10° F E i 0,26 B DO NOT ALTER CAD DRAWING BY HAND 33,3 `0,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH A B A scale: material: tolerance 3:1 SEE SHEET 1 dim. in mm date A title: name drawn 16.07.13 Schmidt RECOMMENDED PANEL CUT-OUT appd. 16.07.13 Fischer D-SUB 15pos. SOLDER CUP with threaded insert and hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 sh: 2 15K1A1343 R a B SEE SHEET 1 A