® MAW01 SERIES DC/DC CONVERTER 1W, SIP-Package FEATURES ►Compact SIP-6 Package ►Small Footprint:17 x 11 mm (0.67”x0.43”) ►Wide 2:1 lnput Range ►Fully regulated Outputs ►Low Ripple and Noise ►Operating Temp. Range -40°C to +85°C ►I/O-isolation Voltage 1500VDC ►Continuous Short-circuit Protection ►Fully RoHS compliant ► 3 Years Product Warranty PRODUCT OVERVIEW The MINMAX MAW01 series is a range of isolated 1W dc/dc-converter modules featuring fully regulated output and wide 2:1 input voltage ranges. This product comes in a very small SIP-6 package occupying only 1.2cm2 (0.2 square inch) on the PCB. A high efficiency allow operating an operating temperature range of -40°C to +85°C without Derating. The very compact dimensions makes these converters an ideal solution for many space critical applications in battery powered instrumentations. Model Selection Guide Model Input Output Number Voltage Voltage Output Current (Range) VDC MAW01-05S05 MAW01-05S12 MAW01-05S15 MAW01-05D12 MAW01-05D15 MAW01-12S05 MAW01-12S12 MAW01-12S15 MAW01-12D12 MAW01-12D15 MAW01-24S05 MAW01-24S12 MAW01-24S15 MAW01-24D12 MAW01-24D15 MAW01-48S05 MAW01-48S12 MAW01-48S15 MAW01-48D12 MAW01-48D15 VDC 5 12 15 ±12 ±15 5 12 15 ±12 ±15 5 12 15 ±12 ±15 5 12 15 ±12 ±15 5 (4.5 ~ 9) 12 (9 ~ 18) 24 (18 ~ 36) 48 (36 ~ 75) Input Current Max. @Max. Load @No Load mA 200 83 67 ±42 ±33 200 83 67 ±42 ±33 200 83 67 ±42 ±33 200 83 67 ±42 ±33 mA(typ.) 263 259 254 262 254 108 108 105 106 106 54 52 52 53 52 27 27 27 27 26 mA(typ.) 40 20 10 7 Max. capacitive Reflected Load Ripple (typ.) current @Max. Load mA (typ.) % 76 77 79 77 78 77 77 80 79 78 77 80 80 80 80 77 78 78 79 79 μF 1680 820 680 470# 330# 1680 820 680 470# 330# 1680 820 680 470# 330# 1680 820 680 470# 330# # For each output E-mail:[email protected] 2012/05/18 P3 Tel:886-6-2923150 Page 1 of 3 80 40 30 20 Efficiency ® MAW01 SERIES DC/DC CONVERTER 1W, SIP-Package Input Specifications Parameter Input Surge Voltage (1 sec. max.) Start-Up Threshold Voltage Internal Filter Type Model Min. Typ. Max. 5V Input Models -0.7 --- 15 12V Input Models -0.7 --- 25 24V Input Models -0.7 --- 50 48V Input Models -0.7 --- 100 5V Input Models --- --- 4.5 12V Input Models --- --- 9 24V Input Models --- --- 18 48V Input Models --- --- All Models Unit VDC 36 Capacitor Output Specifications Parameter Output Voltage Setting Accuracy Line Regulation Load Regulation Min.Load Ripple & Noise (20MHz) Transient Recovery Time Temperature Coefficient Short Circuit Protection Conditions Min. At 50% Load and Nominal Vin ----Vin=Min. to Max. --Single Output Models No Load to Full Load --Dual Output Models --Single Output Models 10% to 90% Load --Dual Output Models No minimum Load Requirement --25% Load Step Change ----Continuous Typ. ------------- Max. ±1.0 ±0.2 ±1.0 ±1.0 ±0.5 ±0.8 Unit %Vnom. % % % % % 50 250 --- ----±0.02 mV P-P μsec %/℃ Typ. Max. Unit General Specifications Parameter Conditions I/O Isolation Voltage (rated) Min. 60 Seconds 1500 --- --- VDC I/O Isolation Resistance 500 VDC 1000 --- --- MΩ I/O Isolation Capacitance 100KHz, 1V --- --- 50 pF --- 220 --- KHz 2,800,000 --- --- Hours Switching Frequency MTBF(calculated) MIL-HDBK-217F@25℃, Ground Benign Environmental Specifications Parameter Conditions Min. Max. Natural Convection -40 +85 ℃ Case Temperature --- +105 ℃ Storage Temperature -55 +125 ℃ Humidity (non condensing) --- 95 % rel. H Lead Temperature (1.5mm from case for 10Sec.) --- 260 ℃ Operating Ambient Temperature Range (See Power Derating Curve) E-mail:[email protected] 2012/05/18 P3 Tel:886-6-2923150 Page 2 of 3 Unit ® MAW01 SERIES DC/DC CONVERTER 1W, SIP-Package Output Power (%) Power Derating Curve Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage, rated output current unless otherwise noted. 2 Ripple & Noise measurement bandwidth is 0-20 MHz. 3 All DC/DC converters should be externally fused at the front end for protection. 4 Other input and output voltage may be available, please contact factory. 5 That “natural convection” is about 20LFM but is not equal to still air (0 LFM). 6 Specifications subject to change without notice. Package Specifications Mechanical Dimensions Pin Connections Pin 3.2 [0.13] 0.5 [0.02] 11.0 [0.43] 17.0 [0.67] 0.5 [0.02] 2.15 [0.08] Single Output Dual Output 1 -Vin -Vin 2 +Vin +Vin 4 +Vout +Vout 5 No Pin Common 6 -Vout -Vout 2.54 5.08 2X2.54 [0.10] [0.20] [2X0.10] 7.62 [0.30] 16.0 [0.63] Bottom View 4 0.50 [0.02] 5 6 2.5 [0.10] 2 0.25 [0.01] 1 ►All dimensions in mm (inches) ►Tolerance: X.X±0.5 (X.XX±0.02) X.XX±0.25 ( X.XXX±0.01) ►Pins ±0.05(±0.002) Physical Characteristics Case Size : 17.0x7.62x11.0mm (0.67x0.30x0.43 inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Pin Material : Alloy 42 Weight : 12.9g 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2012/05/18 P3 Page 3 of 3