产品规格书 SPECIFICATION

规格书编号
SPEC NO:
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF4652
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2007-7-14
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 9
SAW FILTER
HDF4652
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 9
SAW FILTER
HDF4652
1.Features
_ RF bandpass filter for CDMA450 A-Band Rx. Part
_ Usable bandwidth 5MHz (462.5 MHz ~ 467.5 MHz)
_ High attenuation
_ No matching 50Ω single-ended operation
_ Ceramic Surface Mounted Device Package ( 3.0 mm × 3.0mm )
_RoHS Compliant
2. ELECTRICAL SPECIFICATION
Parameter
Operating Temperature Range
Storage Temperature Range
Power Handling Capability
Electronic Characteristics
2-1.Typical frequency response
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
Rating
-30~85
-40~85
27
E-mail:[email protected]
Unit
°C
°C
dBm
Page 3 of 9
SAW FILTER
HDF4652
2-2 Input / Output VSWR Charts
2-3.Electrical characteristics
Minimum
Center Frequency ( F0 )
MHz
Insertion Loss (F0 +/- 2.5 MHz)
465.0
Maximum
-
-
2.6
3.5
-
0.8
1.5
VSWR (F0 +/- 2.5 MHz)
-
1.5
2.0
Relative Attenuation
0.3 MHz ~ 452.5 MHz00
452.5 MHz ~ 457.5 MHz
485.0 MHz ~ 495.5 MHz
495.5 MHz ~ 1200 MHz
1200 MHz ~ 1700 MHz
Input/Output Impedance
45
45
25
45
55
-
50
52
30
50
Amplitude Ripple (F0 +/- 2.5 MHz)
dB
-
Typical
dB
dB
Ω
-
3. TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 9
SAW FILTER
HDF4652
4-1. DIMENSION
5. Environmental Performance Characteristics
Item
High
temperature
Low
temperature
Humidity
Thermal
shock
www.shoulder.cn
Condition
The specimen shall be store at a temperature of
85±2℃ for 96±4h. Then it shall be subjected to
standard atmospheric conditions for 1h, after
which measurement shall be made within 1h.
The specimen shall be store at a temperature of
-30±3℃ for 96±4h. Then it shall be subjected to
standard atmospheric conditions for 1h, after
which measurement shall be made within 1h.
The specimen shall be store at a temperature of
40±2℃ with relative humidity of 90% to 96%
for 96±4h. Then it shall be subjected to standard
atmospheric conditions for 1h, after which
measurement shall be made within 1h.
The specimen shall be subjected to 8 continuous
cycles each as shown below. Then it shall be
subjected to standard atmospheric conditions for
1h, after which measurement shall be made
within 1h.
Temperature
Duration
1
+25℃=>-40℃
0.5h
2
-40℃
4h
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Specifications
Mechanical
characteristics and
specifications
in
electrical
characteristics shall
be satisfied. There
shall
be
no
excessive change in
appearance.
Page 5 of 9
SAW FILTER
Resistance to
Soldering
heat
Solder ability
HDF4652
3
-40℃=>+85℃
2h
4
+85℃
4h
5
+85℃=>+25℃
0.5h
6
+25℃
1h
Reflow soldering method
Peak: 255 ±5 ℃, 220 ±5℃, 40s
At electrode temperature of the specimen.
The specimen shall be passed through the reflow
furnace with the condition shown in the above
profile for 1 time.
The specimen shall be stored at standard
atmospheric conditions for 1h, after which the
measurement shall be made. Test board shall be
1.6 mm thick. Base material shall be glass fabric
base epoxy resin.
Immerse the pins melt solder at 260℃+5/-0℃ More then 95% of
for 5 sec.
total area of the
pins should be
covered with solder
6. Mechanical Test
Items
Vibration
Drop
Lead pull
Lead bend
www.shoulder.cn
Conditions
600-3300rpm amplitude 1.5mm
3 directions 2 H each
On maple plate from 1m high 3 times
Pull with 1kg force for 30 seconds
90o bending with 500g weigh 2 times
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Specifications
There shall be no
damage.
Page 6 of 9
SAW FILTER
HDF4652
7. REMARK
7.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of
the component. Please avoid static voltage.
7.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
7.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
8. Packing
8.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
8.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
8.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 9
SAW FILTER
HDF4652
(3) Leader part and vacant position specifications.
9. TAPE SPECIFICATIONS
9.1 Tensile Strength of Carrier Tape: 4.4N/mm width
9.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.00
±0.30
5.50
±0.10
1.75
±0.10
4.00
±0.10
4.00
±0.10
2.00
±0.10
Ø1.50
Ø1.5
±0.25
0.31
±0.05
1.30
±0.10
3.4
MAX.
3.4
MAX
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 8 of 9
SAW FILTER
HDF4652
[Figure 2]
[Unit:mm]
www.shoulder.cn
A
B
C
D
E
W
t
r
Ø330
±1.0
Ø100
±0.5
Ø13
±0.5
Ø21
±0.8
2
±0.5
13
±0.3
3
max.
1.0
max.
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 9 of 9