规格书编号 : SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF07011A64 SF6-4 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2010-11-11 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDBF07011A64 SF6-4 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 6 SAW FILTER HDBF07011A64 SF6-4 1. SCOPE This specification shall cover the characteristics of SAW filter with HDBF07011A64 used for the page system. 2. ELECTRICAL SPECIFICATION Maximum Input Power DC voltage Storage Temperature Range Operation Temperature Range +10dBm 10V -45℃ to +85℃ -40℃ to +85℃ Electronic Characteristics Parameter Center Frequency Insertion loss Passband ripple(-1 dB) -1dB Bandwidth -3dB Bandwidth -40dB Bandwidth Rejection: 16MHz—63MHz 77MHz—140MHz Min. 69.8 10 10.5 50 55 Typical. 70 22 0.5 10.3 10.7 12.14 Max. 70.2 24 1 12.3 55 60 Unit MHz dB dB MHz MHz MHz dB Absolute Delay 3.5 4 usec Group Delay Variation 100 180 nsec Temperature Coefficient Package Size -87 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 ppm/°C SF6-4 E-mail:[email protected] Page 3 of 6 SAW FILTER HDBF07011A64 SF6-4 Typical Frequency Response 3. TEST CIRCUIT Input : L1 = 120 nH , C1 = 22 pF Output : L2 = 120 nH , C2 =22 pF * Component values may change depending on board layout. 4.DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDBF07011A64 SF6-4 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDBF07011A64 SF6-4 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6