Specification of Electret Condenser Microphone

Specification of
Electret Condenser Microphone
EM6027P
Model No.:
AUG 17 2006
Date:
APPROVER
CHECKER
DESIGN
GUOFENG
HU
RENWEI
YINGBO
XIA
APPROVER
CHECKER
DESIGN
211 N. First Street
Minneapolis, MN. 55401
612-849-6205
[email protected]
50
100
800
1000
1200
3000
5000
1 OF 5 PAGES
Name
:
Model No.:
Scope
Omnidirectional Back Electret Condenser Microphone
EM6027P
:
This specification applies back electret condenser microphone
1、Electrical characteristics
(Temp=20±2℃Room Humidity=65±5%)
No
Parameter
Symbol
1.1
1.2
1.3
Sensitivity
Output impedance
Current Consumption
S
Z out
IDSS
1.4
Signal to Noise Ratio
S/N
1.5
1.6
1.7
Decreasing Voltage
Operating Voltage
Maximum input S.P.L
ΔS-VS
Condition
Min.
0dB=1V/Pa,at 1kHz
f=1kHz
VCC =2.0V,RL=2.2KΩ
at 1kHz S.P.L=1Pa
(A-Weighted Curve)
VCC=1.0V to2.0V
-47
Limits
Center Max.
-44
-41
2.2
500
Unit
dB
KΩ
µA
58
dB
-3
10
110
1.0
dB
V
dB
2. Typical Frequency Response Curve
Frequency Response
Microphone Response Tolerance Window
Frequency(Hz)
Lower Limit(dB)
Upper Limit(dB)
10000
-8
+8
3. Measurement Circuit
RL=2.2KΩ
VS =2.0V
C1=10PF
C2=33PF
C=1µF
-6
-3
-3
0
+3
+3
+3
+8
0
2 OF 5 PAGES
4.Test Setup Drawing
5.Appearance And Dimension
Unit:mm
6.Drawing
11
PIN
Copper
10
FET
1
2SK3857/202
9
CHIP CAPACITOR
2
10 PF +33PF
8
P.C.B
1
FR-4
7
Copper ring
Copper tube
2
1
6
HOUSPING CHAMBER
5
ELECTRET BACK
Gather
formaldehyde
Copper blank
4
SPACER
Mylar
1
3
POLARIZED DIAPHRAGM
DUPONT
1
2
CASE
AL
1
1
FELT
Fabric cloth
1
Name
material
QTY
No.
1
1
Remark
3 OF 5 PAGES
7. Temperature Conditions
Storage Temperature Range
-40℃
8.
~
Operation Temperature Range
+75℃
-40℃ ~
+75℃
Terminal Mechanical Strength
Terminal mechanical strength to be no interference in operation after pulled the terminal with 1kg
strength for 1 minute.
9.
Reliability Test
After any following tests, the sensitivity of the microphone to be within ±3dB of initial sensitivity after 3hours of
conditioning at 20℃.
9-1 Vibration
Frequency1
:
Amplitude
:
:
Change of Frequency
2 hours in each of 3 axes
10Hz~55Hz
1.52mm
1 octave/min
9-2 Dry Heat/Cold
+70℃/-20℃ for
72 hours
9-3 Damp Heat
90%~95%RH,+40℃ for 240 hours
9-4 Temperature Cycles
-20℃
(2h)
(1h)
(2h)
25℃
(1h)
(2h)
70℃
(2h)
×
-20℃
10 cycles
9-5 Packing Drop Test
Height:1m
Procedure: 5 times from each of 3 axis’s
10. Soldering Condition
10-1 The soldering copper of a small type of 13~20W shall be applied.
10-2 The temperature of the working surface of the soldering copper shall be below 320℃.
10-3 ECM shall be soldered fixed on the metal block (heat sink), which has the higher radiation effects said heat sink
shall contact with of ECM.
10-4 The soldering time for each terminal shall be 1~2 sec.
10-5
The pinhole after soldering shall be avoided.
10-6 ECM may easily destroyed by the static electricity and the countermeasure for eliminating the static electricity
(the ground for soldering copper, for worktable and for human body) shall be executed.
4 OF 5 PAGES
10-7
Heat Sink
Shape of heat sink
Shape of hole at fixed part
11. Name Explanation
EXPLANATION
Omni-direction Mic
Back Electret
Meet The Standards Of Rohs
D=6.0mm
T=2.7mm
Pcb version No.2
Dash
Sensitivity –44±3dB
Test Condition 2.2KΩ/2.0V
Dash
Pin=2.8mm
Dash
Capacitance:10+33PF
Dash
No additional parts.
Dash
No especial require
5 OF 5 PAGES
12.Packing Table In Detail
Packing Introduction
Packing
chart
一. P/N:
EM6027P
二. DIMENSION:(LENGTH*WIDTH *HEIGHT)
a)
b)
c)
SMALL PACKET
100mm*100mm*5mm
MID PACKET:
205mm*105mm*50mm
PAPER CASE:
550mm*230mm*235mm
三. EQUIPMENT
a) ADHENSIVE TAPE MACHINE
b) AUTO PACKER
X1
四. PACKING INTRODUCTION
a) 100PCS/ INHALE PLASTIC BOX
b) 1400PCS/MID PACKET
c) 28000PCS/PAPER CASE
五. QUANTITY INTRODUCTION
a) 1PC=0.2g
b) NET WEIGHT
PAPER CASE:5.6kg
GROSS WEIGHT:7.6kg
六、 LABEL STIPULATION
a. LABELEDEVERY BOXES
(SEE THE CHART)
b. DIMENSIONS SHOULD BE SEEN EASILY
100PCS
X14
1400PCS
X20
28000PCS