Surface Mount Optically Coupled Isolator JAN / JANTX / JANTXV 4N22U, 4N23U, 4N24U Features: Surface Mount (SM), Leadless Chip Carrier (LCC) 1 kV electrical isolation Base contact provided for conventional transistor biasing JAN, JANTX and JANTXV devices are processed to MIL-PRF-19500 Description: Each isolator in this series consists of an infrared emitting diode and a NPN silicon phototransistor, which are mounted in a hermetically sealed Surface Mount, 6 Pin package. Devices are designed for military and/or harsh environments. The JAN / JANTX / JANTXV 4N22U, 4N23U and 4N24U devices are processed to MIL-PRF-19500/486. This series of 4N products are JEDEC registered, DSCC qualified. Please contact your local representative or OPTEK for more information. Applications: Military equipment High-Reliability environments High voltage isolation between input and output Electrical isolation in dirty environments Industrial equipment Medical equipment Office equipment DIMENSIONS ARE IN INCHES [ MM ] Pin # LED Pin # 3 Collector 2 Transistor N/A 4 Base 1 Anode 5 Emitter 6 Cathode This product is built, tested and shipped from the USA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue F 04/2015 Page 1 of 4 Surface Mount Optically Coupled Isolator JAN / JANTX / JANTXV 4N22U, 4N23U, 4N24U Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Storage Temperature Range -65° C to +150° C Operating Temperature Range -55° C to +125° C ± 1.00 kVDC(1) Input-to-Output Isolation Voltage Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] ESD Class 260° C(2) 1C Input Diode Forward DC Current (65° C or below) 40 mA Reverse Voltage 2V Peak Forward Current (1 µs pulse width, 300 pps) 1A 60 mW(3) Power Dissipation Output Sensor: Continuous Collector Current 50 mA Collector-Emitter Voltage 40 V Collector-Base Voltage 45 V Emitter-Base Voltage 4V 300 mW(4) Power Dissipation Notes: 1. Measured with input leads shorted together and output leads shorted together. 2. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 3. Derate linearly 1.0 mW/° C above 65° C. 4. Derate linearly 3.0 mW/° C above 25° C. Ordering Information Part Number Isolation Voltage (kV) IF (mA) Typ / Max VCE (Volts) Max Processing MIL-PRF195000 1 10 / 40 40 486 JAN4N22U JANTX4N22U JANTXV4N22U JAN4N23U JANTX4N23U JANTXV4N23U JAN4N24U JANTX4N24U JANTXV4N24U This product is built, tested and shipped from the USA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue F 04/2015 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Surface Mount Optically Coupled Isolator JAN / JANTX / JANTXV 4N22U, 4N23U, 4N24U Electrical Characteristics (TA = 25°C unless otherwise noted) PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS Onput Diode IF = 10.0 mA IF = 10.0 mA, TA = -55° C(1) IF = 10.0 mA, TA = +100° C(1) VF Forward Voltage 0.80 1.00 0.70 - 1.50 1.70 1.30 V IR Reverse Current - - 100 µA VR= 2.0 V V(BR)CEO Collector-Emitter Breakdown Voltage 40 - - V IC = 1.0 mA, IB= 0, IF= 0 V(BR)CBO Collector-Base Breakdown Voltage 45 - - V IC = 100 µA, IB= 0, IF= 0 V(BR)EBO Emitter-Base Breakdown Voltage 7 - - V IE = 100 µA, IC= 0, IF= 0 IC(OFF) Collector-Emitter Dark Current - - 100 100 nA µA VCE = 20 V, IB= 0, IF= 0 VCE = 20 V, IB= 0, IF= 0, TA = 100ºC ICB(OFF) Collector-Base Dark Current - - 100 nA VCB = 20 V, IE= 0, IF= 0 Ω 0.15 2.50 1.00 1.00 - - IF = 2.0 mA , VCE = 5 V, IB = 0 IF = 10.0 mA , VCE = 5 V, IB = 0 (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = -55° C (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = 100° C JAN / JANTX / JANTXV 4N23 [A] 0.20 6.00 2.50 2.50 - - IF = 2.0 mA , VCE = 5 V, IB = 0 IF = 10.0 mA , VCE = 5 V, IB = 0 (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = -55° C (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = 100° C JAN / JANTX / JANTXV 4N24 [A] 0.40 10.0 4.00 4.00 - - - - 0.30 0.30 0.30 100 - - V VCE = 5.0 V , IC = 10.0 mA, IF = 0 mA 11 - - Ω V10 = ± 1.0 VDC(3) Output Phototransistor Coupled On-State Collector Current JAN / JANTX / JANTXV 4N22 [A] IC(ON) Collector-Emitter Saturation Voltage VCE(SAT) HFE JAN / JANTX / JANTXV 4N22 [A] JAN / JANTX / JANTXV 4N23 [A] JAN / JANTX / JANTXV 4N24 [A] DC Current Gain mA IF = 2.0 mA , VCE = 5 V, IB = 0 IF = 10.0 mA , VCE = 5 V, IB = 0 (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = -55° C (1) IF = 10.0 mA , VCE = 5 V, IB = 0, TA = 100° C V IF = 20 mA , IC = 2.5 mA, IB = 0 IF = 20 mA , IC = 5.0 mA, IB = 0 IF = 20 mA , IC = 10.0 mA, IB = 0 RIO Resistance (Input-to-Output) CIO Capacitance (Input-to-Output) - - 5 pF VI-O = 0 V, f = 1.0 MHz(3) Output Rise and Fall Time - - 20 µs VCC = 10.0 V , IF = 10.0 mA, RL = 100 Ω TR, TF Notes: 1. 2. 3. 10 Guaranteed but not tested. Sample tested, LTPD = 10. Measured with input leads shorted together and output leads shorted together. This product is built, tested and shipped from the USA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue F 04/2015 Page 3 of 4 Surface Mount Optically Coupled Isolator JAN / JANTX / JANTXV 4N22U, 4N23U, 4N24U Typical Performance Curves Forw ard Voltage vs Forw ard Current vs Tem perature -55° V F - Forward Voltage (V) 1.5 1.4 -35° 1.3 -15° 1.2 +5° 1.1 +25° 1.0 +45° 0.9 +65° 0.8 0 5 10 15 20 +85° 25 IF - Forw ard Current (m A) +105° -55° Collector Current vs Forw ard Current vs Tem perature 700% 600% IC(ON) - Normalized Collector Current (%) -35° Normalized at +25°C -15° 500% +5° 400% +25° 300% +45° 200% +65° 100% +85° 0% 0.0 1.0 2.0 3.0 4.0 +105° 5.0 IF - Forw ard current (mA) +125° Normalized Collector Current Vs Temperature Normalized Collector Current Vs Temperature 140% Normalized Collector Current (%) I F = 1 mA and V CE = 5 100% I F = 1mA 80% 60% 40% 20% 0% -55° -35° -15° +5° +25° +45° +65° +85° +105° +125° Normalized Collector Current (%) 140% Nor mal i z ed at +25°C 120% Nor mal ized at +25°C 120% IF = 2 mA and VCE = 5 V 100% IF = 2mA 80% 60% 40% 20% 0% Temperature (°C) -55° -35° -15° +5° +25° +45° +65° +85° +105° +125° Temperature (°C) This product is built, tested and shipped from the USA OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue F 04/2015 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Surface Mount Optically Coupled Isolator JAN / JANTX / JANTXV 4N22U, 4N23U, 4N24U Issue A A.1 Change Description Approval 05/08/07 Initial Release 03/31/2009 Updated graphs on page 2 B Delete CTR% column for all products C Master Page: Changed from Issue B 08/2010 to Issue C 06/2011. Header: Added JAN to TX & TXV . Page 1: Description: Added 4N products are JEDEC registered, DSCC qualified. Ordering Information table: Added “JAN” to TX & TXV. Combined JANTX & JANTXV ordering lines and moved to Page 2. Inserted new mechanical drawing. Removed PB /RoHS symbols from left bottom corner. Page 2: Moved “NOTES” from Page 3 to Page 2 / added 7th note. Moved colored graphs from Page 2 to Page 3. Page 3: Vf table: Removed [A] and added U to part #s. Changed (1) to (7). Iceo table: Changed (1) to (7). Page 4: Added table header. Ic(on) table: Added (7). Page 5: Removed all “A” / [A] from table. Ic(on) table: Added (7). R10 table: Added (1). Page 7: Added Packaging Options. Date S. De La Garza 8/27/2010 K. Bland / Sergio 8/19/11 D Add JAN to all headers, to Features and Description Add the Made in USA test at the bottom of every page. Update the VCE volts from 35 to 40. Change the Collector-Emitter voltage from 35 to 40 and the Collector-Base voltage from 35 to 45. Sergio De La Garza 2/26/14 E Corrected drawings on page 1 Sergio De La Garza 4/28/15 F Add ESD class to Absolute Maximum Ratings OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue F 04/2015 Page 5 of 4