Reflective Object Sensor OPB609 Series Features: • • • • RA OPB609 emitter (940 nm IR-LED) Unfocused for sensing diffuse surface Low-cost plastic housing High-speed phototransistor output GU AX Description: The OPB609 consists of an 940 nm, Light Emitting Diode (LED) and an NPN silicon Phototransistor, which are mounted “side-by-side” on parallel axes in a black opaque plastic housing. This unfocused reflective object sensor is ideal for detection of diffuse materials such as paper, labels, or anything with a matte finish. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • • • • • • • • • Ordering Information Non-contact reflective object sensor Assembly line automation CONTAINS POLYSULFONE Machine automation To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Machine safety Vibra-Tite evaporates fast without causing structural failure in OPTEK’s molded plastics. End-of-travel sensor Door sensor Edge detection Paper jam detection Mark detection 0.374 [9.5] 0.107 [2.70] Function 1 Anode 2 Cathode 3 Collector 4 Emitter OPB609AX 3 1 2 OPB609AX OPB609GU Reflective Object Sensor with IR LED OPB609RA 0.134 [3.40] 0.071 [1.80] 4 Description 0.006 [0.15] Min. Pin # Part Number DIMENSIONS ARE IN: 0.026 [0.65] 0.038 [0.95] [ MILLIMETERS] INCHES 0.026 [0.65] 0.020 [0.50] OPB609GU 0.059 [1.50] 0.005 [0.12] 0.038 [0.95] RoHS OPB609RA 0.134 [3.40] 0° - 20° 0.370 [9.4] Min. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.3 08/08 Page 1 of 3 Reflective Object Sensor OPB609 Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature Range -40° C to +85° C Operating Temperature Range -40° C to +100° C Lead Soldering Temperature [1/16 inch (1.6 mm) from the case for 5 seconds with soldering iron](1) 260° C(1) Input LED Forward DC Current 50 mA Peak Forward Current (1 μs pulse width, 300 pps) 1A Reverse DC Voltage 5V Power Dissipation(2) 75 mW Output Phototransistor Collector-Emitter Voltage 30 V Emitter-Collector Voltage 5V Collector DC Current 50 mA Power Dissipation(3) 75 mW Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input IR LED (see OP168 for additional information) VF Forward Voltage - - 1.7 V IF = 20 mA IR Reverse Current - - 10 µA VR = 5 V θ Beam Divergence - 90 - Degree IF = 20 mA Output Phototransistor (see OP508 for additional information) V(BR)CE0 Collector Emitter Breakdown Voltage 30 - - V IC = 100 µA V(BR)ECO Emitter Collector Breakdown Voltage 5 - - v IE = 100 µA Collector Dark Current - - 100 nA VCE = 10 V, IF = 0 - - 0.4 V EE = 2.0 mW/cm2, IC = 2 mA ICEO Coupled Characteristics V CE(SAT) Collector Emitter Saturation Voltage I C(ON) On-State Collector Current 200 - - µA IF = 20 mA, Vce = 5 V, d = 0.110” (2.79 mm) I C(OFF) Off-State Collector Current - - 200 nA VCE = 5 V, IF = 20 mA Notes: 1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 2. 3. Derate linearly 1.25 mW/°C above 25°C. Derate linearly 1.33mW/°C above 25°C. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.3 08/08 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Reflective Object Sensor OPB609 Series OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.3 08/08 Page 3 of 3